How to Read the Tire Pressure on an Air Gauge?

1 Answers
StMelanie
07/30/25 3:39am
Method for reading tire pressure on an air gauge: Align the interface of the tire pressure gauge with the tire's inflation valve and press firmly. At this point, the vehicle owner can see the tire's air pressure. Most common tire pressure gauges are marked with two units of pressure: Bar and Psi. The commonly mentioned 2.2 or 2.0 pressure refers to Bar, and either unit can be used. Tire pressure refers to the air pressure inside the tire, which is essentially the 'blood pressure' of a car. The level of tire pressure plays a crucial role in the performance and power of the vehicle. Insufficient tire pressure increases tire deformation, leading to cracks on the sidewalls and causing flexing movements, which result in excessive heat generation, rubber aging, fatigue in the cord layers, and cord breakage. It also increases the tire's contact area with the ground, accelerating wear on the tire shoulders. Excessive tire pressure overextends and deforms the tire cords, reducing the tire's elasticity and increasing the load on the vehicle while driving. In case of impact, it may cause internal cracks or even blowouts. Additionally, high pressure accelerates wear on the tire tread and reduces its resistance to punctures.
Was this review help?
14
3
Share
More Forum Discussions

What is the function of the Wuling PCV valve?

PCV valve mainly functions to guide the gases from the crankcase into the intake manifold through the PCV valve, with a small amount of air entering the intake manifold directly from the air filter via the PCV valve. This prevents phenomena such as icing at the throttle, incomplete combustion, and worsened emissions, while also preventing blow-by gases from entering the atmosphere and avoiding oil deterioration. The working principle of the PCV valve is introduced as follows: 1. Introduction one: The PCV valve is a metering control valve installed between the crankcase ventilation system and the intake system. The PCV is controlled by vacuum, regulating the flow of oil fumes generated by the crankcase ventilation system into the intake system. The flow rate is higher when the engine operates at high speeds compared to low speeds. Additionally, when engine backfire occurs, the PCV valve should cut off ventilation to prevent crankcase explosion. 2. Introduction two: At the end of the engine's combustion process, some unburned mixture leaks into the crankcase under high pressure through the piston rings, which is referred to as "blow-by" in the industry. These blow-by gases can escape from the crankcase into the atmosphere, causing pollution. If not expelled, these blow-by gases can also dilute the engine oil, leading to premature oil deterioration and causing early wear to the engine.
14
4
Share

Is the Corolla 1.5L a three-cylinder or four-cylinder engine?

1.5L naturally aspirated engine is a three-cylinder. Below is relevant information about the Corolla: Space: The Corolla has been lengthened in terms of body size, with its wheelbase reaching 2700mm after the extension. In terms of seating space, a tester with a height of 177cm adjusted the front seat to the lowest position, leaving a fist's worth of headroom. When the tester moved to the rear seat, there was 2 fingers' worth of headroom and 1 fist and 3 fingers' worth of legroom. The floor bulge in the middle of the Corolla's rear seat is minimal. Power: Overall power is good, with quick acceleration but relatively slow starts. The engine noise is low, but in reality, when driving exceeds 80 kilometers per hour, the tire noise becomes significant, leading some owners to modify their cars for sound insulation. The new dual VVT-i engine pairs perfectly with the CVT continuously variable transmission, providing ample 2.0L power; the six-speed manual transmission is highly precise with clear gear engagement; however, the four-speed transmission is somewhat outdated.
10
0
Share

Does the VV6 have a particulate filter?

2021 VV6 models are equipped with particulate filters. This feature is standard across all B-segment and above vehicles. A particulate filter is a ceramic filter installed in the diesel engine's emission system, designed to capture particulate matter before it enters the atmosphere. It can reduce soot emissions from diesel engines by over 90%, with the captured particles being burned off during vehicle operation. How the particulate filter works: The diesel particulate filter is coated with platinum, rhodium, and palladium. The black smoke containing carbon particles emitted by the diesel engine enters the particulate filter through a dedicated pipe. Inside, a densely arranged bag-type filter captures the carbon particles on a metal fiber felt filter. When the accumulated particles reach a certain level, an automatic burner at the end ignites, burning off the carbon particles and converting them into harmless carbon dioxide. To check if the VV6 has a particulate filter, you can use these three methods: Check the and to see if the particulate filter function is mentioned. Additionally, review the fault codes in the manual for any "particulate filter" warning light indicators. Look at the label on the oil filler cap. If it specifies 0W-20 grade oil, it indicates the presence of a particulate filter. Inspect the exhaust pipe behind the catalytic converter for an additional cylindrical section. If present, that is the particulate filter.
6
0
Share

What is the fuel tank capacity of the Scirocco in liters?

The 2016 Scirocco 1.4TSI Club edition has a fuel tank capacity of 55 liters. It is equipped with a 1.4L turbocharged engine and a 7-speed dry dual-clutch transmission (DCT). The drivetrain configuration is front-engine, front-wheel drive. The front suspension is a MacPherson independent suspension, while the rear suspension is a multi-link independent suspension. Among comparable models, the 2022 BMW Z4 sDrive25i M Sport package has a fuel tank capacity of 52 liters, while the 2021 Mustang 2.3L EcoBoost has a 58.9-liter fuel tank. During actual refueling, the amount of fuel may exceed the nominal capacity. This is because the manufacturer's specified fuel tank capacity is measured from the bottom of the tank to the safe fill level, with additional space remaining between the safe fill level and the tank opening. This space allows for fuel expansion when temperatures rise, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual refueled amount may exceed the nominal tank capacity. To check the remaining fuel level, owners can observe the fuel gauge on the right side of the instrument panel, which is marked with E (Empty) and F (Full). When the needle approaches E, it indicates low fuel, while proximity to F means the tank is nearly full.
1
4
Share

What are the dimensions of the BMW X5 in terms of length, width, and height?

The dimensions of the BMW X5 are 4930mm in length, 2004mm in width, and 1776mm in height, with a wheelbase of 2975mm. The BMW X5 is an imported vehicle positioned as a mid-to-large-size SUV. The currently available model is the 2019 version, which complies with the China VI emission standards. The 2019 BMW X5 features a front-engine, four-wheel-drive layout with an on-demand four-wheel-drive system. BMW X5 Suspension: The 2019 BMW X5 is equipped with a double-wishbone independent front suspension and a multi-link independent rear suspension, with electric power steering. BMW X5 Safety Features: Driver/passenger airbags, front side airbags, front/rear head airbags, tire pressure monitoring, run-flat tires, rear child seat ISOFIX anchors, anti-lock braking system (ABS), brake force distribution (EBD), brake assist (BA), traction control (ASR), electronic stability control (ESC), active braking, and driver fatigue alert. BMW X5 Assist Features: Front/rear parking sensors, rearview camera, drive mode selection, automatic parking assist, auto start-stop technology, auto hold, hill start assist, hill descent control, variable steering ratio, sport appearance package, power tailgate, engine immobilizer, central locking system, keyless start system, active grille shutters, etc.
13
4
Share

What are the methods to test if a generator is not producing electricity?

When suspecting that the generator is not producing electricity, you can test it on the vehicle without disassembling the generator to determine if there is a fault. The testing methods are as follows: 1. Voltage test: When the engine is running, set the multimeter knob to the DC voltage 30V range at the battery terminal. Connect the red probe to the generator's "armature" terminal and the black probe to the casing. Run the engine at medium speed or higher. The standard voltage for a 12V electrical system should be around 14V, while for a 24V system, it should be around 28V. For small cars, the measured voltage is usually above 13.8V, often reaching over 14V. If the generator is not producing electricity, the voltage will drop significantly after starting, often falling below 12V. If the measured voltage is the same as the battery voltage, it indicates the generator is not producing electricity. 2. External ammeter test: If the car dashboard does not have an ammeter, you can use an external DC ammeter for testing. First, disconnect the "armature" terminal wire of the generator, then connect the positive terminal of the ammeter (with a range of about 20A) to the generator's "armature" and the negative terminal to the disconnected wire. When the engine runs at medium speed or higher, if the ammeter shows a charging indication of 3A~5A, the generator is working normally; otherwise, it is not producing electricity. 3. Test lamp method: If you don't have a multimeter or a DC ammeter, you can use a car bulb to make a test lamp. Solder wires of appropriate length to both ends of the bulb and attach alligator clips to the ends. Before testing, disconnect the "armature" terminal wire of the generator, then clip one end of the test lamp to the generator's "armature" terminal and the other end to the ground. If the lamp lights up when the engine runs at medium speed, the generator is working normally; otherwise, it is not producing electricity. 4. Changing engine speed and observing headlight brightness: After starting the engine, turn on the headlights and gradually increase the engine speed from idle to medium speed. If the headlights' brightness increases with the speed, the generator is working normally; otherwise, it is not producing electricity. 5. Removing the battery ground to check engine operation: If the vehicle does not have microcomputer-controlled electronic devices, you can use this method for testing. Run the engine at medium speed or higher, then disconnect the battery ground wire. If the engine continues to run normally, the generator is producing electricity; otherwise, the generator is faulty.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.