How to Properly Start and Park the Golf 8?

2 Answers
LucyAnn
09/07/25 4:53am
Start: Press the brake pedal and push the one-touch start button. Shut down: After parking the vehicle, press the start button again to turn it off. Start: Press the ignition switch directly without stepping on the brake pedal. Press the start button once more to turn off all dashboard lights. Parking: Step on the brake, shift to N gear, release the brake, pull the handbrake, turn off the engine, and shift to P gear.
Was this review help?
4
2
Share
LeMatthew
09/19/25 4:16am
I've been driving for over 20 years, and starting the Golf 8 is quite simple—just press the one-touch start button while firmly pressing the brake. If you only want to power on to listen to music, press the button without stepping on the brake. The parking procedure is crucial: after stopping by pressing the brake, immediately shift to P, and the electronic parking brake will engage automatically, then press the button to turn off the engine. I make it a habit to turn off the AC and headlights before shutting down to protect the battery. When parking on a slope, it's best to straighten the steering wheel to reduce strain on the steering system. You'll hear a confirmation beep when locking the car with the key, which is reassuring. It's also good practice to check around the car before starting, looking for obstacles or fluid leaks.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

Why Does a Dual-Fuel Vehicle Automatically Switch from Gas to Gasoline?

Dual-fuel vehicles may automatically switch to gasoline due to low gas pressure, as the power output when running on gas is generally lower than when running on gasoline. Below is relevant information about bi-fuel vehicles: 1. Fuel Supply System: A bi-fuel vehicle is equipped with two independent fuel supply systems. One supplies natural gas or liquefied petroleum gas (LPG), while the other supplies gasoline or diesel. These two fuel supply systems can individually, but not simultaneously, deliver fuel to the engine cylinders. The driver can switch between gas and fuel modes using a dedicated fuel switch button. 2. Electronic Control Logic: The bi-fuel control system processes signals from gas-related sensors (such as the pressure regulator temperature sensor and high-pressure sensor) and controls actuators (like the gas injector and pressure regulator) directly through a single ECU.
9
4
Share

What is the formal name of the handbrake?

The formal name of the handbrake is the auxiliary brake. Here is an introduction to the handbrake: 1. Introduction: The handbrake is used to stabilize the vehicle after it has stopped, preventing accidents caused by rolling on inclined surfaces. 2. Location: Common handbrakes are usually placed within easy reach of the driver's right hand for convenience, though some models may position the parking brake on the side of the brake pedal. 3. Principle: The parking brake only acts on the rear wheels, utilizing two metal cables to pull the rear brake pads to achieve braking. Normally, when the handle is pulled to about 70% of its full travel, the handbrake should be in the proper braking position. Before testing the handbrake's braking force, it's necessary to locate this point, which can be determined by counting the clicks of the ratchet. The 70% position is the effective working point of the handle.
12
5
Share

Kawasaki X300 Fuel Consumption?

Kawasaki X300 fuel consumption is approximately 2.55L per 100 kilometers. Methods for calculating fuel consumption: By measuring the amount of fuel added during a refill and recording the distance traveled, the vehicle's fuel consumption can be calculated. The fuel consumption obtained through these two methods represents the average fuel consumption of the vehicle. Ways to save fuel: When driving in urban areas, traffic congestion is common. Therefore, experienced riders often plan their routes in advance to avoid heavily congested areas. Reducing frequent starts and stops, and maintaining an economical speed can effectively save fuel.
12
0
Share

What are the differences between four-wheel drive and two-wheel drive vehicles?

Here are the differences between four-wheel drive and two-wheel drive vehicles: 1. Power: Four-wheel drive vehicles have outstanding power and strong off-road capability, making them suitable for off-road driving. Four-wheel drive can distribute the engine's power to all four wheels, significantly improving the vehicle's handling and passage ability. Two-wheel drive vehicles balance off-road and urban driving. 2. Interior: Whether it's the exterior, interior, driving visibility, or driving experience, two-wheel drive models are basically no different from four-wheel drive models. 3. Usage: On normal roads, vehicles generally use rear-wheel drive. However, once encountering poor road conditions or wheel slippage, the computer automatically detects and immediately distributes the engine's torque to the front two wheels, naturally switching to four-wheel drive mode. This eliminates the need for driver judgment and manual operation, making it simpler to use.
18
0
Share

What is the speed limit for light trucks on highways?

Blue-plate light trucks have a speed limit of 100 km/h on highways, with a minimum speed not lower than 60 km/h. Highway speed limit values: The highway speed limit shall not exceed 120 km/h, and the limit value should be an integer multiple of 10 km/h. The difference between speed limits of two adjacent sections should not exceed 20 km/h. For highway interchanges, the speed limit difference between mainlines, deceleration lanes, and exit ramps should not exceed 30 km/h. Speed limit sign design: Speed limit signs should be designed to be more concise, clear, and aesthetically pleasing. They should be installed at the starting point of speed-limited sections without being obstructed by roadside trees, structures, or other traffic signs, and should be repeated as needed.
7
1
Share

Can you change lanes on a double yellow dashed line?

Double yellow dashed lines allow lane changes. Here are the relevant details about yellow dashed lines: 1. Lane change indication: Dashed lines indicate that crossing is permitted, meaning lane changes are allowed. When encountering yellow dashed lines on the road, as long as you're in the dashed line area and obeying traffic signals and yielding rules, U-turns or lane changes are permitted. 2. Follow road markings: This not only reduces accidents but also improves traffic efficiency. Always obey road markings to create a healthier and more efficient driving environment. Remember one key point: Never cross if your side has a solid line; if your side has a dashed line, crossing is permitted.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.