How to Practice Driving Without a Sense of Direction?

1 Answers
SanTheo
07/25/25 9:21pm
Practice techniques for driving without a sense of direction: 1. Gentle steering: When adjusting the direction of the vehicle, steer gently and smoothly. Pay attention to the conditions behind and in front of the vehicle, making slight adjustments with small angles to gradually correct the driving direction. 2. Avoid abrupt or fast movements: Never change the vehicle's direction too abruptly or quickly while driving. For example, if the vehicle is initially tilting to the right, an overly aggressive adjustment might cause it to tilt to the left or even cross the road edge line, leading to test failure. During high-speed driving (e.g., in the third driving test), adjust the vehicle's direction by turning the steering wheel just two or three finger-widths, preferably in several small steps. 3. Posture: Sit upright and straight while driving, look far ahead, and keep your grip on the steering wheel relaxed. Ensure the vehicle's direction aligns with your line of sight. The farther you look ahead, the sooner you can detect any issues with the vehicle.
Was this review help?
3
3
Share
More Forum Discussions

Where is the Xiaopeng P7 manufactured?

Xiaopeng P7 is produced at the Zhaoqing factory, belonging to the Xiaopeng Motors brand. Below is an introduction to the Xiaopeng P7: 1. Powertrain: The 2020 model P7 launched by Xiaopeng, the rear-wheel-drive ultra-long-range version, has a range of 706km. The motor has a maximum torque of 390N·m, maximum power of 196kW, and maximum horsepower of 267Ps. 2. Parameters: For owners who enjoy spirited driving, Xiaopeng also offers a four-wheel-drive high-performance version with superior parameters. The rear-wheel-drive ultra-long-range version has a tested range of up to 600km at an average speed of 35~40km/h. 3. Safety: The Xiaopeng P7 is equipped with 6 airbags, 4 high-precision collision sensors, and electric seat belts. Its protection level ranks among the top in its class. When the sensors detect a severe impact, the high-voltage electricity is automatically cut off to prevent secondary injuries. The passenger compartment features a cage-like structure, with the A-pillar integrated with the front longitudinal beam, subframe, and front crossbeam, significantly buffering impacts from the front and sides.
7
3
Share

Is the fuel consumption of the 1.5L Yinglang high?

The Buick Yinglang 2021 1.5L automatic elite version has a fuel consumption of 7.5 liters per 100 kilometers. It is not high. Here is more information about the Buick Yinglang: 1. Appearance: The Buick Yinglang is an excellent sedan model under the Buick brand. The model draws on the classic elements of the Rivera concept car. The vehicle not only has a fashionable and elegant appearance but also boasts an outstanding powertrain configuration. 2. Endurance: The Buick Yinglang 2021 1.5L automatic elite version is equipped with a 6-speed automatic transmission and has a fuel tank capacity of 44L. With a full tank, the Buick Yinglang can travel at least 500km.
16
3
Share

What is the Difference Between Full Trailer and Semi-Trailer for Tractor Trucks?

Introduction to the differences between full trailer and semi-trailer for tractor trucks: I. Different characteristics. 1. Semi-trailer: Compared to "single-unit" vehicles, semi-trailers can improve the comprehensive economic benefits of road transportation. Transportation efficiency increases by 30-50%, costs are reduced by 30-40%, and fuel consumption decreases by 20-30%. The use of semi-trailers can also promote certain improvements in logistics organization. 2. Full trailer: It has no independent power and relies on other vehicles for towing. II. Different uses. 1. Semi-trailer: Mainly used for transporting large, indivisible goods such as excavators. Flatbed trailers are more suitable for fresh goods like vegetables and fruits, while enclosed trailers are better for bulk goods, moisture-sensitive, or more valuable items. 2. Full trailer: Widely used in airports, ports, railway stations, factories, and large warehouses. It significantly improves the efficiency of cargo transfer and reduces the cost and labor consumption of forklifts.
11
2
Share

What is the automotive PCM module?

Automotive PCM module is the engine control module. Here are the detailed introductions: 1. PCM is used for power output control. It receives sensor signals and performs complex calculations to control fuel supply, air distribution (electronic throttle), injection and ignition timing, intake pressure adjustment. It also determines the engine compensation control coefficient based on temperature, load, knock, combustion conditions, etc. 2. PCM also performs system diagnostic functions, capable of identifying operational faults. It alerts the driver through the MIL (Malfunction Indicator Lamp) and stores identified diagnostic trouble codes. It helps technicians complete repairs by distinguishing fault locations. 3. The engine control calibration program is stored in an electrically erasable programmable read-only memory (EEPROM), which is a permanent memory soldered onto the ECM and cannot be replaced separately. When replacing the ECM, the new ECM must be programmed according to the configured vehicle model before it can be used.
18
3
Share

How Long Can an Engine Generally Last After Cylinder Boring?

Generally, a car engine can run about 3,000 kilometers after cylinder boring, but with proper assembly, it may last hundreds of thousands of kilometers. Here are some extended details: 1. After cylinder boring, the engine requires a break-in period similar to a new car, covering two to three thousand kilometers. The longevity depends on the extent of the overhaul and parts replacement. If all four matching parts are replaced, the crankshaft and bearing shells are in good condition, and the oil seals are renewed, the engine can run another 100,000 or even 200,000 kilometers without issues. 2. Cylinder boring is necessary when the engine has been running for a long time, causing severe cylinder wear, which inevitably leads to "oil leakage." This results in symptoms like burning oil, reduced power, and increased fuel consumption. 3. Cylinder boring is a common repair method for excessively worn dry cylinder liners. Since a thin layer is "polished" off the cylinder wall surface, the cylinder diameter inevitably becomes slightly larger.
2
4
Share

What does Maintenance A and Maintenance B mean?

A Maintenance and B Maintenance refer to the service codes for vehicle maintenance. A Maintenance is a minor service, while B Maintenance is a major service. Here are the detailed explanations: 1. A Maintenance, commonly known as a minor service, typically refers to the basic maintenance tasks performed at the manufacturer's recommended time or mileage intervals to ensure vehicle performance. It mainly includes oil and oil filter replacement. During engine operation, metal friction generates debris, and impurities and moisture from the air mix into the oil. Continuous lubrication and high-temperature working conditions cause the oil itself to deteriorate and lose effectiveness. The oil filter's efficiency also diminishes over time due to prolonged filtration, making timely replacement necessary. 2. B Maintenance is a major service for the vehicle, performed at the manufacturer's recommended time or mileage intervals. In addition to oil and oil filter replacement, it includes tasks such as replacing the air filter, cabin air filter, brake fluid, and transmission fluid. Therefore, B Maintenance includes A Maintenance, and the two are usually alternated. The selection of major maintenance items can be entirely based on the vehicle's maintenance manual.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.