How to Perform Throttle Body Adaptation After Cleaning on a Camry?

1 Answers
DeBrady
07/30/25 7:07am
Turn the key to the power-on position without starting the engine. The Camry is a model under GAC Toyota, featuring a sophisticated exterior and user-friendly functions. Let it sit for about 10 seconds, then quickly press the accelerator pedal all the way down and hold for 15 seconds before rapidly releasing it. Turn off the ignition and remove the key, then wait for approximately 15 seconds. It comes in three major series (Luxury, Sport, and Hybrid) with ten variants, all meeting China's National VI emission standards. Start the vehicle normally to complete the adaptation. The lineup is equipped with three powertrain options: TNGA 2.5L HEV, TNGA 2.5L, and TNGA 2.0L.
Was this review help?
18
2
Share
More Forum Discussions

How to Accelerate a Motorcycle from 0 to 100?

Increase torque by replacing the engine's small sprocket with one that has fewer teeth and the rear wheel's large sprocket with one that has more teeth, but this will reduce the top speed. Replace the cylinder and piston with larger ones, but this is more complicated, and the quality of aftermarket cylinders and pistons may not be as reliable as the original parts. Adjust the mixture slightly richer and replace the carburetor with one that has an accelerator pump, but this will increase fuel consumption.
15
0
Share

What to Do When the Clutch Pedal is Hard to Press?

First, press the clutch pedal several times while the car is running to see if there's any improvement in gear shifting. If there is improvement, it indicates air in the clutch hydraulic system. Bleed the air and try again. If the hydraulic fluid level is sufficient, check around the clutch master cylinder and slave cylinder for any signs of oil leakage. If leakage is found, replace the leaking slave cylinder or master cylinder. The clutch disc needs replacement as it wears out over time. Replacing the clutch disc requires separating the engine from the transmission.
4
0
Share

How to Adjust the Two Screws on the Cruze Headlights?

Drive the car to a relatively flat road surface, adjust the low beam point to 30 meters apart with two points overlapping, and adjust the high beam point to be parallel to the ground. Park the car about 7.5 meters away from the wall, ensuring that the car is perpendicular to the wall and level with the ground. Adjust the vertical adjustment screw until the headlight beam is centered on the tape on the wall. Measure the height of the headlights and the beam on the wall. If the heights are consistent, it indicates that the headlight adjustment is perfect.
11
2
Share

What is the difference between a two-axle vehicle and a four-axle vehicle?

There are mainly the following differences between a two-axle vehicle and a four-axle vehicle: 1. The number of drive axles is different: a two-axle vehicle has 2 drive axles, while a four-axle vehicle has 4 drive axles. 2. The load capacity varies: two-axle trucks have a relatively small load capacity and are generally used for lighter goods. Four-axle vehicles have a larger load capacity and can be used for heavier goods. 3. The off-road performance is different: four-axle vehicles have better off-road performance than two-axle vehicles and can travel longer distances, so two-axle vehicles are generally used for shorter distances.
10
3
Share

Where is the emergency keyhole on the All-New Santa Fe?

The All-New Santa Fe does not have an emergency keyhole. When the key fob battery is dead, simply press the key against the start button for induction starting. Below are the relevant details:1. Dimensions: Length × Width × Height (mm) 4,930x1,910x1,720, Wheelbase (mm) 2,865.2. Design: The Santa Fe is equipped with a 380TGDi engine paired with an 8-speed automatic transmission, along with HTRAC intelligent four-wheel drive control system. This delivers robust power while ensuring smooth gear shifting and superior traction, providing families with a stable and comfortable driving experience.
10
3
Share

What Type of Motor is Used in Pure Electric Vehicles?

There are three main types of motors used in new energy vehicles: DC motors, asynchronous motors, and permanent magnet synchronous motors. The permanent magnet synchronous motor has become the mainstream choice due to its wide speed range, high power density, simple manufacturing process, compact size, and reliable, durable operation. Below are specific details about new energy vehicles: 1. Definition: New energy vehicles refer to automobiles that utilize unconventional vehicle fuels as their power source, integrating advanced technologies in power control and driving systems to create vehicles with advanced technical principles, new technologies, and innovative structures. 2. Types: New energy vehicles include pure electric vehicles, range-extended electric vehicles, hybrid vehicles, fuel cell electric vehicles, hydrogen engine vehicles, etc.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.