How to Park and Retrieve Cars in an Automated Parking System?

1 Answers
Ortiz
07/25/25 12:22pm
Automated parking systems allow for automatic vehicle storage and retrieval on the first level, functioning similarly to a ground-level parking lot. The system will automatically recognize card swipe information. After the driver or parking attendant swipes the card, the automated parking system moves the vehicle-carrying platform vertically and horizontally. The driver can then enter the garage and drive the car away directly.
Was this review help?
16
5
Share
More Forum Discussions

What is the minimum ground clearance of the Corolla?

The minimum ground clearance of the Corolla is 145mm, which refers to the distance between the lowest point of the car (excluding the wheels) and the supporting plane when the car is fully loaded and stationary. It is used to characterize the car's ability to pass over obstacles such as stones and stumps without collision. The Corolla is a Toyota car equipped with a newly developed in-line four-cylinder 1.8L engine (2ZR type) with dual VVTi technology, matched with a 6-speed manual transmission or a 4-speed automatic transmission. In terms of body size, the Corolla has a length, width, and height of 4545mm, 1760mm, and 1490mm respectively, with a wheelbase of 2600mm.
19
3
Share

How to Disassemble a Buick Verano Car Key?

The method to disassemble a Buick Verano car key is as follows: 1. At the small groove of the hook, use a flat-head screwdriver to pry gently towards the back. 2. A gap will appear, then slowly pry it open. The method to replace the car key battery is as follows: 1. Remove the key ring, use a 1-yuan coin to fit into a groove on the key, then twist the coin to open it and replace the CR1620 button battery. 2. Identify the positive and negative poles (positive down, negative up), and install it in place as it was. 3. Initialization: After replacing the key, initialization is required to restore the remote control function.
9
3
Share

How to use the cruise control on the Nissan Patrol?

Here are the steps to use the cruise control on the Nissan Patrol: 1. Press the ON/OFF key to activate the system (the cruise control indicator light on the dashboard will illuminate); 2. Accelerate to your desired speed (above 40km/h), then press the SET key (you can now release the accelerator pedal as the speed is set at the current value); 3. Press "RES+" to increase speed or "SET-" to decrease speed based on the current setting; 4. Three methods to deactivate cruise control: press the brake pedal, press the CANCEL key, or press the ON/OFF key; 5. If cruise control was canceled via brake pedal or CANCEL key, press RES to resume the previously set cruise speed.
14
5
Share

What are the reasons for a car not starting after being parked for a week?

The reasons for a car not starting after being parked for a week: 1. The car battery is dead, you can jump-start it using another vehicle with a charged battery; 2. The car battery has reached the end of its lifespan, simply replace it with a new one. The car battery is a crucial component of the vehicle, as it powers all electronic devices when the engine is not running, and it is also responsible for starting the engine. When the car is not used for an extended period, you can disconnect the negative terminal of the battery to avoid discharging. If the car is left unused for a long time without disconnecting the negative terminal, it may lead to battery discharge. A car battery that remains discharged for a long time can significantly shorten its service life.
10
1
Share

How to Use the Cruise Control on Jeep Cherokee?

Here are the detailed steps for using the cruise control on Jeep Cherokee: 1. First, pull the control lever inward to activate the system. Store the current speed by pressing the set button. 2. Push the lever upward to increase speed, or downward to decrease speed. 3. To maintain a constant speed, quickly push the lever up or down. The function will be temporarily canceled by pressing the accelerator or pushing the lever downward. Releasing the accelerator or pushing the lever inward will automatically resume the function. Pushing the lever to the end or applying the brake will cancel the function, and the indicator light will turn off. 4. DISTANCE button: Press this button to display the current driving distance. Pushing left or right adjusts the following distance from the vehicle ahead, automatically regulating speed. If a rear-end collision is imminent and the driver fails to brake in time, the system will take control to avoid a collision.
9
0
Share

What does the yellow triangle with an exclamation mark on the car dashboard mean?

The yellow triangle with an exclamation mark on the car dashboard is the traction control indicator, also known as the ground adhesion control system indicator. When the traction control light is on, it alerts the driver to turn off the traction control system. Typically, this light flashes when the TCS (Traction Control System) is active. If the light remains constantly illuminated, it indicates a fault in the traction control system. Generally, the yellow triangle exclamation mark on the dashboard rarely appears. When it does, it is often due to a vehicle malfunction, and the driver should take the car to a repair shop for inspection as it cannot be resolved independently. It is important not to ignore this warning, and it is recommended to contact a professional technician for inspection as soon as possible.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.