How to Open the Trunk of a Toyota Prado?

1 Answers
McHaley
07/29/25 10:01pm
Toyota Prado's trunk can be opened by directly pulling the trunk door handle, which is located next to the license plate and is a side-swing door. The trunk dimensions are 978mm in depth, 1290mm in width, and 906mm in height. The 2010 Toyota Prado is equipped with a 2.7L naturally aspirated engine, delivering a maximum horsepower of 163ps and a maximum power output of 120kw, paired with a 5-speed manual transmission. In terms of suspension, the 2010 Toyota Prado features a front suspension type of double-wishbone independent suspension and a rear suspension type of four-link solid axle non-independent suspension.
Was this review help?
17
3
Share
More Forum Discussions

How to Lift Windshield Wipers in Snowy Conditions?

To lift windshield wipers in snowy conditions, follow these steps: activate the maintenance mode to position the wipers at their highest point, then you can lift them. The replacement method for windshield wipers is: 1. Lift the wiper; 2. Press the clip below to remove the wiper blade; 3. Take off the old wiper; 4. Pry up the front end of the middle clip; 5. Insert the new wiper into the middle clip, pull it tight by hand, and the replacement is complete once you hear a click. Usage tips for windshield wipers: 1. Avoid parking in areas with intense sun exposure, frost, or excessive dust; 2. Do not operate the wipers dry on sunny days; 3. Manually remove hard debris, leaves, sand, or ice from the windshield; 4. Minimize the use of the wiper's fast setting; 5. Handle the wipers gently during car washes and routine maintenance.
4
0
Share

How Much Should You Fill the Oil When Changing It?

When changing the oil, it is appropriate to fill it to a point slightly above the middle between the lower and upper marks on the dipstick. The method for changing the oil is as follows: 1. Lift the car, remove the undercover, and place a container under the oil drain plug; 2. Unscrew the oil drain plug, use an air gun to blow into the oil filler for two minutes, then tighten the drain plug and wipe it with a tissue to check for leaks; 3. Reinstall the undercover, lower the car, and add oil through the filler port. Precautions for changing the oil: 1. Perform the change while the engine is warm to ensure the old oil is drained as completely as possible; 2. Add oil and ensure the amount is appropriate; 3. After adding oil, start the engine and check all components for leaks. Run the engine for 3 minutes to confirm the oil level is at the normal mark.
16
0
Share

What is the solution for a clogged oil pump?

The solution for a clogged oil pump is: 1. Add or replace engine oil; 2. Clean or replace the oil filter screen; 3. Replace the oil suction pipe and gasket; 4. Replace the pressure relief valve spring; 5. Replace the injector valve core. Symptoms of a damaged oil pump are: 1. Weak acceleration, with jerking during sudden acceleration; 2. Difficulty starting, requiring prolonged key turning; 3. A buzzing sound while driving; 4. The engine warning light turns on; 5. Engine vibration occurs. The working principle of an oil pump is: When the engine is running, the drive gear on the camshaft drives the transmission gear of the oil pump, causing the drive gear fixed on the drive gear shaft to rotate, which in turn drives the driven gear to rotate in the opposite direction, delivering oil from the inlet chamber through the gear gap and pump wall to the outlet chamber.
16
1
Share

How to Deal with Rusty Car Doors?

Methods to handle rusty car doors: 1. If the rust is on the surface and the area is small, you can use water sandpaper to grind off the rust and then spray a layer of anti-rust paint; 2. If the rust has damaged the primer, you need to remove the rust by grinding, spray the primer, and then proceed with topcoat spraying; 3. If the car door is severely rusted with large areas of paint peeling, it is necessary to completely remove the rusted paint, fill and level it with putty, and then spray paint after the putty hardens. Causes of car door rust: After collisions or scratches, the metal body is directly exposed to the outside. Besides common collisions, scratches, and rust from long-term parking, another situation is when small stones kicked up by the tires of the car in front cause small impacts during driving, leading to tiny paint peel-offs and small rust spots. Regularly inspect the car body, engine cover, and around the car, and address any issues immediately once discovered.
4
2
Share

What is the minimum ground clearance of the Talagon?

The minimum ground clearance of the Talagon is 200mm. Here is some knowledge about the Talagon: 1. Vehicle Positioning: Volkswagen's latest global flagship SUV: The Talagon, as a heavyweight flagship product launched on the 30th anniversary of FAW-Volkswagen, will upgrade the brand value based on the 30-year cooperation in brand and technology between FAW Group and Volkswagen Group, practicing brand elevation and truly impacting the luxury brand market. 2. Industry Level: As a new product in the large SUV market, the Talagon closely follows the upgraded needs of the new middle-class users, integrating high-end business and luxurious comfort design elements into the interior design. While meeting users' demands for SUV off-road performance and exterior design, it also satisfies users' all-scenario needs through interior designs that surpass those of luxury cars, truly achieving the goal of being suitable for both business and family use, as well as off-road capabilities.
3
5
Share

What is the method for waxing a sedan?

The method for waxing a sedan is: 1. Wash the car thoroughly with a dedicated car wash solution; 2. After rinsing the car, dry it with a clean cloth to avoid water on the paint surface affecting the waxing effect; 3. Move the car to a shaded area, use a round sponge specifically for solid car wax to apply the wax evenly on the paint surface; 4. During application, move the sponge in circular motions across the car body to create a fish-scale effect with the wax on the paint; 5. After application, wait 5 to 10 minutes for the wax to dry completely; 6. Use a microfiber towel to wipe off any excess wax from the paint surface. Precautions for waxing are: 1. Wax every 3 to 4 months; 2. Do not wax a new car casually; 3. Clean the car before waxing; 4. Wax the car in a shaded area.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.