How to Open the Trunk of a Chevrolet Sail?

How to Activate the 4WD System on the Buick Envision?

The Buick Envision features an automatic all-wheel-drive (AWD) system that does not require manual activation. Below are the specific details about the Buick Envision's intelligent AWD system: 1. The intelligent AWD system can dynamically distribute power between the front and rear axles based on road conditions during highway driving. Compared to full-time 4WD systems, the intelligent AWD system enhances agility, stability, and handling responsiveness on highways. 2. During acceleration, the system actively distributes power between the front and rear axles. At high-speed cruising, power is primarily delivered to the rear axle, and at certain speeds, up to 100% of the power may be allocated to the rear axle. This ensures stability and agility during acceleration while improving fuel efficiency during high-speed cruising. For most daily highway driving, the intelligent AWD system maintains driving stability while optimizing fuel economy.

16

0

Share

How to Remove the Fuel Filter Clip on Cadillac XTS?

To remove the fuel filter clip on a Cadillac XTS, use pliers to pull it downward. Below are the steps for removing the fuel filter on a Cadillac XTS: 1. Lift the vehicle and disconnect the sensor plug on the fuel filter. 2. Use a tool to remove the screws on the fuel filter, typically requiring a 10cm wrench or a Torx screwdriver. 3. Use a screwdriver to detach the clip on the fuel filter and pull it backward to separate the tension plug from the tension socket. 4. When removing, ensure the arrow on the fuel filter points upward. 5. Remove the fuel filter and install the new one according to the size and orientation of the old filter. Incorrect orientation may affect fuel flow. 6. Tighten the base screws with a tool and reconnect the fuel filter sensor line.

9

3

Share

When was the 2020 all-new Tiguan L launched?

The 2020 all-new Tiguan L was launched on October 13, 2020. Here is an introduction to the Tiguan L: 1. Overview: The Tiguan L is produced by SAIC Volkswagen and offers a total of 7 models equipped with 1.8T (330TSI) and 2.0T (380TSI) engines. The SAIC Volkswagen Tiguan L plug-in hybrid version was officially launched, providing two models: the Hybrid Luxury Edition and the Hybrid Flagship Edition. 2. Exterior: The Tiguan L retains a design similar to the overseas standard Tiguan model, featuring a clean and straightforward style. Compared to the standard wheelbase model, it includes additional chrome trim pieces and some changes to the C-pillar design. The Tiguan L measures 4712mm in length, 1839mm in width, and 1673mm in height, with a wheelbase of 2791mm. 3. Safety Features: In terms of safety, the all-new Tiguan L comes standard with ESP vehicle stability system and front side airbags. The top-tier Supreme Flagship model includes a pre-collision safety protection system, knee airbags, lane-keeping system, 360-degree parking camera, and HUD head-up display system.

15

0

Share

What brand is GY6?

GY6 is from Honda. Here are the related introductions: 1. Introduction to GY6: The GY6 engine is a pressure-splash lubricated forced air-cooled engine with high power, originally produced by Honda Motor Co., Ltd. The carburetor type is a vacuum diaphragm carburetor with a choke resistor. The GY6 engine is also an engine above 125cc, used in fully faired motorcycles, such as Lingying 125, Daxian 125 or 150, Dr. A, etc. 2. GY6 engine parameters: (1) Compression ratio: 9.2:1; (2) Power (original Haomai): 6.2KW/7500RPM; (3) Power (replica): 5.4KW/7500RPM; (4) Oil capacity (Haomai): 750ml; (5) Gear oil capacity: 110ml; (6) Carburetor type: Vacuum diaphragm carburetor with choke resistor; (7) Matched carburetor model: MIKUNI BS24.

7

2

Share

When will the Mercedes-Benz GLB be domestically produced?

Mercedes-Benz GLB achieved domestic production by the end of 2019. Below are the specific details about the Mercedes-Benz GLB: 1. The Mercedes-Benz GLB is a compact SUV under the Mercedes-Benz brand. 2. The dimensions of the Mercedes-Benz GLB are 4638 mm in length, 1834 mm in width, and 1687 mm in height. 3. The Mercedes-Benz GLB is equipped with two types of engines: a low-power version 1.3-liter turbocharged engine and a high-power version 2.0-liter turbocharged engine. The low-power 1.3-liter turbocharged engine delivers 136 horsepower and a maximum torque of 200 Nm, with a maximum power output at 5500 rpm and a maximum torque range between 1460 to 4000 rpm. The high-power 1.3-liter turbocharged engine produces 163 horsepower and a maximum torque of 250 Nm, with a maximum power output at 5500 rpm and a maximum torque range between 1620 to 4000 rpm. 4. The front suspension of the Mercedes-Benz GLB uses a MacPherson independent suspension, while the rear suspension employs a multi-link independent suspension.

19

1

Share

How to Change License Plate Number for ETC?

ETC license plate number change procedure: The vehicle owner needs to bring their ID card and photocopy, vehicle license and photocopy, ETC device, and the bank card bound to the ETC account to the bank. After the bank staff verifies the documents, they will cancel the ETC binding with the original license plate information and rebind it to the new license plate number. The bank staff will then install the ETC device in the vehicle and activate it on-site for normal use. The ETC installation process is as follows: Upon receiving the device, first check if the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU; the red light will briefly turn on, and the OLED screen will display "Tag Invalid" or "Please Insert Card," indicating the device is functioning properly. Clean the front windshield to ensure the surface is smooth, clean, and dry. Then, peel off the adhesive backing of the OBU and stick it to the installation position. Press firmly for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the windshield. The chip should be inserted into the OBU device. ETC activation method: Insert and remove the ETC card twice in succession until the electronic tag screen displays "Bluetooth On." If "Tag Invalid" appears when inserting and removing the card twice without the electronic tag attached, this is normal and does not affect activation. Alternatively, press the button on the top of the electronic tag to enable Bluetooth. Turn on the mobile phone's Bluetooth and open the corresponding mobile app (usually a QR code for download is provided on the electronic tag). Navigate to the device activation interface. Click on "Device Connection" and wait patiently for the "Connection Successful" prompt. Once connected, upload a photo of the vehicle's front to complete activation.

12

3

Share

How to Open the Trunk of a Chevrolet Sail?

How to Activate the 4WD System on the Buick Envision?

How to Remove the Fuel Filter Clip on Cadillac XTS?

When was the 2020 all-new Tiguan L launched?

What brand is GY6?

When will the Mercedes-Benz GLB be domestically produced?

How to Change License Plate Number for ETC?

What is HAVAL?

What type of engine oil should be used for Geely Vision sedan?

Geely Emgrand Trunk Suddenly Won't Close

What does the blue color on the Mazda3's water temperature gauge mean?