How to open the fuel tank of Verna?

Why Does an Electric Vehicle Have Weak Acceleration?

Here are the reasons for weak acceleration in electric vehicles: 1. Demagnetization of the motor: Many users park carelessly, often leaving the electric vehicle exposed to direct sunlight, which can cause demagnetization of the motor. 2. Battery aging or swelling: Irregular charging habits can accelerate battery aging and even lead to swelling. Once the battery swells, the vehicle's range will significantly decrease, resulting in insufficient power and weak acceleration. 3. External resistance issues: External resistance in electric vehicles typically manifests in two forms: tire pressure problems and brake locking. Insufficient tire pressure increases resistance during driving, leading to weak acceleration.

3

5

Share

What Lights Should You Turn On When Driving in Heavy Rain?

When driving in heavy rain, turn on the headlights or front fog lights. Precautions for driving in rainy weather are as follows: 1. Turn on the windshield wipers promptly; 2. If there is frost on the windshield, turn on the air conditioning and direct the cold air toward the windshield; 3. Hold the steering wheel with both hands to maintain balance, drive straight and at a low speed, and brake gently to prevent the tires from locking up and causing the vehicle to skid; 4. Reduce the vehicle's speed, pay attention to the distance between the front and rear vehicles, and be mentally prepared to take emergency measures in advance. Car headlights, also known as car front lights or car LED daytime running lights, can be maintained by: 1. Regularly checking the sealing of the headlights—replace the sealing ring between the lens and reflector if it is damaged; 2. Regularly cleaning the reflector—replace it if it turns black or the brightness decreases; 3. Regularly removing dust and stains from the bulbs.

13

0

Share

What to Do When the Car Starter Motor Fails and the Engine Won't Start?

When the starter motor fails and the engine needs to be started: 1. Manual transmission: You can use first or second gear to start the vehicle. For example, engage first gear, press the clutch, and have someone push the car or use another vehicle to tow it. Once the car gains speed, release the clutch, and the engine should start. 2. Automatic transmission: You can only seek professional help or send the car to a repair shop. Below is an introduction to common starter motor failures: 1. Poor electrical connection: This could be due to insufficient battery power, loose wiring connections, dirty terminals causing poor contact, or a faulty starter solenoid switch with broken coils or poor contact. 2. Broken or burnt coils: The starter relay contacts may be burnt, or the relay magnetic coil may be broken or burnt out.

4

Share

What does the mnemonic rhyme 'left yields to right, turning yields to going straight' mean?

The mnemonic 'right turn yields to left turn, left turn yields to going straight' is a traffic yielding rule, meaning that when driving, right-turning vehicles must yield to left-turning vehicles, and when turning left, left-turning vehicles must yield to vehicles going straight. According to Article 51 of the 'Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China', motor vehicles passing through intersections controlled by traffic signals shall follow these rules: 1. Designated lanes: At intersections with designated lanes, enter the lane corresponding to the intended direction of travel. 2. Roundabouts: Vehicles preparing to enter a roundabout must yield to vehicles already inside the roundabout. 3. Left turns: When turning left, turn from the left side of the intersection center point. Use turn signals when turning, and low beams when driving at night. 4. Green light: When encountering a green light, proceed in order. 5. Red light: When encountering a red light, stop in order behind the stop line. If there is no stop line, stop before the intersection. 6. Right turns: When turning right and encountering a vehicle in the same lane waiting for a green light, stop and wait in order. 7. No traffic signals: At intersections without directional traffic signals, turning vehicles must yield to vehicles and pedestrians going straight. Right-turning vehicles from the opposite direction must yield to left-turning vehicles.

7

1

Share

Why is the hood of a new car very hot?

Because the heat dissipated by the engine accumulates on the hood. The following is relevant information about the hood: 1. Introduction: Made of rubber foam and aluminum foil materials, it reduces engine noise while isolating the heat generated during engine operation, effectively protecting the paint on the hood surface and preventing aging. 2. Function: Airflow diversion. For objects moving at high speed in the air, the air resistance and turbulence generated by the airflow around the moving object directly affect its trajectory and speed. The shape of the hood can effectively adjust the direction of the airflow relative to the car's movement and the resistance force it generates, reducing the impact of airflow on the car. Through diversion, air resistance can be decomposed into beneficial forces, increasing the force of the front tires on the ground, which helps stabilize the car's movement. The streamlined appearance of the hood is basically designed based on this principle.

20

0

Share

How many meters apart are highway expansion joints?

Ordinary concrete road surfaces have expansion joints every 10-15m. Joint width: 4-6mm. More details are as follows: 1. Definition: Contraction joints, commonly known as dummy joints (English term: contraction-joint), refer to shrinkage joints set in large-area concrete slabs. Their function is to prevent irregular cracks from forming when the cement concrete slab contracts. 2. Saw cut depth: When dowel bars are installed, the depth should not be less than 1/3 of the slab thickness and must be at least 70mm. When no dowel bars are installed, it should not be less than 1/4 of the slab thickness and must be at least 60mm. The principle for saw cutting is 'better early than late, better deep than shallow'. During hot weather construction, joint filler should be flush with the slab surface. In cold weather, the filler should form a concave surface with the center 1-2mm below the slab surface.

18

0

Share

How to open the fuel tank of Verna?

Why Does an Electric Vehicle Have Weak Acceleration?

What Lights Should You Turn On When Driving in Heavy Rain?

What to Do When the Car Starter Motor Fails and the Engine Won't Start?

What does the mnemonic rhyme 'left yields to right, turning yields to going straight' mean?

Why is the hood of a new car very hot?

How many meters apart are highway expansion joints?

How to Handle the Vehicle License for a Used Car?

What does EPS mean in cars?

What are the symptoms of a faulty turbocharger bypass valve?

Is it serious if the coolant level is below MIN?