How to Most Accurately Align with the Pole When Parking on a Slope?

Where Are the Accelerator and Brake Pedals Located in an Automatic Transmission Car?

In an automatic transmission car, the brake is on the left, and the accelerator is on the right. This is because an automatic transmission car has two pedals in the driver's compartment, whereas a manual transmission car has three. Below is a detailed introduction to the car pedals: The accelerator pedal is a car accessory designed to give the driver more control over the pedal, thereby enhancing driving safety. Most accelerator pedals are made of aluminum alloy. Adding an accelerator pedal can significantly increase the vertical contact area of the pedal. The brake pedal is the pedal that limits power, also known as the foot brake. It is used to decelerate and stop the car and is one of the five major controls in car driving, used very frequently. How the driver controls it directly affects driving safety. How to Press the Accelerator in a Manual Transmission Car: Pressing the accelerator in a manual transmission car requires a gentle and gradual approach. This means the pedal should be pressed down slowly to allow the speed to increase steadily, resulting in a smoother acceleration process with less intense push-back feeling. If the accelerator is continuously pressed, the speed will gradually increase even without further pressure. At this point, the accelerator should be slowly released. Because the accelerator is sensitive, suddenly releasing it can cause the car to jerk. Important Tips for New Drivers: When changing lanes or turning, always signal in advance: Lights and horns are the language of driving. Your intentions must be communicated to others, especially for new drivers. Always signal early—the earlier you communicate, the safer it is. When changing lanes or turning, make it a habit to use your turn signals and avoid the bad habit of turning or changing lanes immediately after signaling. Instead, signal in advance to prevent accidents. Don’t rush when overtaking; follow the proper procedure: When overtaking, activate the left turn signal in advance and use high and low beams or honk the horn. On roads without a centerline or with only one lane in the same direction, the vehicle ahead should slow down and move to the right to give way when it receives an overtaking signal from the vehicle behind, if conditions permit. The overtaking vehicle should ensure there is sufficient safe distance before passing on the left side of the vehicle ahead. After maintaining a necessary safe distance from the overtaken vehicle, activate the right turn signal and return to the original lane. Check surroundings before reversing: When reversing, always check the surroundings first. Do not blindly rely on rearview mirrors, parking sensors, or backup cameras. If someone is guiding you while reversing, the guide should stand beside the vehicle, not behind it, to avoid being hit. Slow down and observe when approaching intersections: Intersections have vehicles, pedestrians, and non-motorized vehicles coming from all directions, making them complex. Therefore, always develop the habit of looking around (while slowing down) when approaching an intersection, regardless of traffic lights or whether your lane has a green light. Observe the situation on the crosswalk and confirm there are no vehicles rushing through before accelerating through the intersection. Check for tailgating vehicles before emergency braking: When braking suddenly, pay attention to the vehicles behind you. It’s best to maintain a safe distance from the vehicle ahead and avoid emergency braking to prevent rear-end collisions. Maintain a safe distance from the vehicle ahead: Road conditions can be unpredictable. The vehicle ahead might stop suddenly, or a pedestrian might dart out. Therefore, always control your speed and never exceed the speed limit. Additionally, maintain a safe distance from the vehicle ahead to allow enough time to react and avoid accidents. Some vehicles may change lanes without signaling; having enough distance will give you time to respond calmly. Slow down and check surroundings when turning: Always slow down when turning. In some areas, pedestrians and non-motorized vehicles may use the motor lane. When turning, especially, use the rearview mirror to check for pedestrians or non-motorized vehicles behind or beside you. If you spot any, proactively avoid them to prevent collisions. Drive in the middle lane when possible: When driving on the road, it’s best to stay in the middle lane. On roads without a central divider, driving in the middle lane gives you time to react if an oncoming vehicle has an emergency, preventing head-on collisions. On roads with dividers, if someone or a vehicle suddenly emerges from the divider, you’ll have time to react. Additionally, driving in the middle lane at night prevents being blinded by oncoming headlights, which could obscure pedestrians or vehicles in the middle of the road and lead to accidents. Slow down and honk in poor visibility: In areas or weather conditions with poor visibility, driving can be challenging. Always honk and slow down in advance to ensure safe passage. Slow down when approaching parked large vehicles: If there are large vehicles parked on the roadside ahead, be extra cautious. Large vehicles can block your view, and if a vehicle, pedestrian, or non-motorized vehicle suddenly emerges from beside the large vehicle, it could lead to an accident. Therefore, slow down in such situations and proceed only when it’s safe.

3

1

Share

Do Toyota vehicles have a particulate filter?

Toyota's latest naturally aspirated and hybrid models do not have a particulate filter, while the older Highlander models do. A particulate filter is a ceramic filter installed in the exhaust system of diesel engines, designed to capture particulate emissions before they enter the atmosphere. It can reduce soot emissions from diesel engines by more than 90%, and the captured particulate matter is subsequently burned off during vehicle operation. How a particulate filter works: The diesel particulate filter is coated with metals such as platinum, rhodium, and palladium. The black smoke containing carbon particles emitted by the diesel engine enters the particulate filter through a dedicated pipe. Inside, a densely arranged bag-type filter captures the carbon particles on a metal fiber felt filter. Once the accumulated particles reach a certain level, a burner at the end automatically ignites, burning off the captured carbon particles and converting them into harmless carbon dioxide. To check if a Toyota vehicle has a particulate filter, you can use the following three methods: 1. Check the and to see if the particulate filter function is mentioned. Additionally, carefully review the fault codes in the manual to check for a "particulate filter" warning light indicator. 2. Look at the label on the oil cap. If the oil cap clearly states the use of 0W-20 grade oil, it indicates the presence of a particulate filter. 3. Inspect the exhaust pipe behind the catalytic converter to see if there is an additional cylindrical section. If present, that is the particulate filter.

9

1

Share

What could be the possible causes of steering wheel vibration?

The cause of steering wheel vibration may be a fault in the steering system. Below is a detailed introduction to the automotive steering system: 1. Components: The automotive steering system mainly consists of the steering wheel assembly, steering column assembly, rack and pinion power steering gear and tie rod assembly, power steering (hydraulic or electric) system, and wheel assembly. 2. Function: During driving, the vehicle needs to frequently change its direction of travel according to the driver's will, which is referred to as vehicle steering. For wheeled vehicles, the method to achieve vehicle steering is that the driver uses a specialized mechanism to make the wheels (steering wheels) on the vehicle's steering axle (usually the front axle) deflect a certain angle relative to the vehicle's longitudinal axis.

16

2

Share

What should motor vehicles do when temporarily parked on the roadside?

Here is a detailed introduction to the precautions for motor vehicles when temporarily parked on the roadside: 1. Check the signs to determine whether temporary parking is allowed. First, observe whether there are parking restriction signs in the section. Temporary parking is only allowed if it is a time-limited parking area. 2. Check the rearview mirror for safety. Before parking, reduce the speed, then turn on the right turn signal and observe the right rearview mirror to see if there are any vehicles or pedestrians behind on the right side. 3. Engage the handbrake and turn on the hazard warning lights. Pull the handbrake or press the parking button. If you leave the vehicle briefly, it is best to turn off the engine, lock the doors and windows, and place a contact number in a visible place on the window.

7

2

Share

What to Do When the Automatic Transmission P Gear Cannot Be Engaged?

Automatic transmission P gear locking mechanism consists of a locking gear, a locking pin, and a set of motion mechanisms. After engaging the P gear, the cable drives the connecting ball pin, at which time the working pin slides to make the locking pawl tightly fasten the parking gear, and the vehicle's gear shift is locked, making it impossible to pull the gear lever. Below are the relevant introductions: 1. Solution for when the automatic gear lever cannot be pulled in P gear: If you need to shift to other gears, you must first start the vehicle and then engage other gears; or press the brake pedal and then switch gears. When parking, always ensure the vehicle is completely stopped before engaging the P gear, otherwise, it is easy to encounter this situation where the gear lever cannot be pulled in P gear. 2. Working principle of the automatic P gear: When the gear lever is placed in P gear, the parking lock mechanism locks the transmission output shaft. In P gear, the drive shaft is partially locked inside the transmission, so even without pressing the brake on flat ground, the vehicle has a certain braking force.

15

3

Share

How to Adjust Gas Idle Vibration?

Methods to adjust gas idle vibration: 1. If the idle jet and idle air jet are clogged, clean them with gasoline or acetone and blow them through with compressed air; 2. If there is air leakage at the intake manifold or the lower gasket of the carburetor, use tightening screws or add/subtract gaskets to fix it; 3. If idle instability is accompanied by a decrease in engine power, further check the spark plugs' condition, the sealing performance of the valves, and the correctness of the ignition timing. If necessary, perform maintenance and adjustments. The main causes of gas idle vibration include: uneven combustion of natural gas, clogged idle air jets, poor performance of the idle device, weak spark in individual spark plugs, poor sealing of individual valves, air leakage in the intake manifold, and ignition timing that is too early or too late.

11

1

Share

How to Most Accurately Align with the Pole When Parking on a Slope?

Where Are the Accelerator and Brake Pedals Located in an Automatic Transmission Car?

Do Toyota vehicles have a particulate filter?

What could be the possible causes of steering wheel vibration?

What should motor vehicles do when temporarily parked on the roadside?

What to Do When the Automatic Transmission P Gear Cannot Be Engaged?

How to Adjust Gas Idle Vibration?

What to Do If the Self-Scheduled Subject 1 Test Differs from the Driving School's Arrangement?

What to Do When Your Foot Shakes Badly During the Subject 2 Driving Test?

What to Use to Clean the Inside of the Windshield Without Leaving Marks?

What is the difference between inverted and conventional shock absorbers?