How to Match the Tire Pressure Monitoring System on Baojun 310?

What Causes the Engine Not to Start When the Water Temperature is High?

When a car's water temperature is too high and it fails to start, the issue is primarily due to component damage caused by problems in the cooling system. The car's cooling system consists of components such as the radiator, auxiliary tank, water pump, water pump belt, fan, thermostat, coolant, water passages within the engine block, and coolant pipes. In theory, a car should not be started or driven when the water temperature is excessively high. It is advisable to stop the engine and inspect the problem to prevent damage to car components that could lead to failure to start. The correct procedure when the engine is overheating due to insufficient coolant is as follows: 1. Find a safe place to pull over: Let the vehicle idle without turning off the engine, as shutting it down will stop both the cooling fan and coolant circulation, causing the engine to become even hotter. 2. Open the hood: This increases airflow, allowing the water temperature to drop. Then, slightly loosen the radiator cap to release internal steam before fully opening it. 3. Do not add coolant immediately: As physics teaches, heat causes expansion while cold causes contraction. Boiling water in a sealed container generates pressure. If the radiator cap is opened immediately after boiling, the internal pressure can cause the hot water to spray out, potentially leading to burns.

5

2

Share

What Happens When You Press the Accelerator While in Park?

Pressing the accelerator while an automatic transmission car is in Park is generally harmless. The engine will idle, and the RPM will rise rapidly, resulting in louder noise and increased fuel consumption. Automatic transmission cars simplify driving by eliminating the need for manual gear shifting, essentially making them 'foolproof' vehicles. However, driving an automatic isn't just about pressing the accelerator and brake; there are other considerations to extend the car's lifespan. More details are as follows: 1. Parking Stopper: Most parking spaces have a low stopper at the rear to guide drivers when parking. If your tires touch the stopper while reversing into a spot and you shift directly into Park (P), you may notice that shifting out of P later is difficult, accompanied by a 'click' sound and vehicle jerk. This happens because the automatic transmission's P mode engages a set of locking pins inside the gearbox, effectively locking the vehicle in place. 2. Caution: If the tires hit the stopper while the car is still moving during reversing and you shift directly into P, the force of the impact is locked into the transmission's P-mode mechanism, leaving the car in a stressed state. Shifting out of P later forces the gear lever to pry open the locked pins, causing noise and jerking, which can damage the transmission over time. The correct procedure is to shift into Neutral (N) after the tires touch the stopper, release the brake to let the car settle naturally, and then shift into P to avoid any issues.

5

0

Share

How to Convert Between Power and Horsepower?

Power is a physical quantity, while horsepower is a unit; there is no direct conversion between them. The unit of power is the watt, and the conversion between watts and horsepower is: 1 metric horsepower = 75 kilogram-force·meters/second = 735 watts. Power refers to the amount of work done by an object per unit of time, meaning power describes the rate at which work is performed. Horsepower is a commonly used unit for measuring power in engineering. Below are some driving tips: 1. Check the rearview mirrors: When turning or changing lanes, always use the turn signals, slow down, and check the rearview mirrors before turning. Left turns mainly require checking the left rearview mirror, right turns mainly require checking the right rearview mirror, and both left and right turns require checking the interior rearview mirror. 2. Don’t focus on the area directly in front of the car: When driving on clear roads, look straight ahead about 100 meters, not just at the immediate front of the car. 3. Press the clutch: Generally, when decelerating at speeds above 40 km/h, there’s no need to press the clutch first; wait until the speed drops to around 20 km/h before pressing the clutch. 4. Steering: Turn the steering wheel slowly at high speeds and quickly at low speeds.

2

Share

What is the diameter of 700c wheels?

700*21C refers to a 700C size tire with a width of 21mm. 700C indicates a wheel with a rim size of 622mm. The earliest 700C wheels used 35C tires, resulting in a total wheel diameter of approximately 700mm when including the tire. The 'C' stands for millimeters. When replacing rims, pay attention to the following parameters: 1. Center Bore (CB): This refers to the size of the center hole of the rim. Although rims with different center bore sizes can be installed using adapters, it is not recommended for safety reasons. 2. Pitch Circle Diameter (PCD): For example, a rim with a PCD of 5x120mm means it has 5 lug bolts arranged in a circle with a diameter of 120mm. This value should also adhere to the original specifications.

11

0

Share

What is the 750 car?

There are two models of the 750 car: the BMW 750 and the Roewe 750. The BMW is a high-end luxury sedan produced by the German BMW company. It belongs to the "BMW 7 Series" and is only produced in Germany. The Roewe 750 is the first mid-to-high-end sedan product mass-produced in China with pure British design and technical genes. Here is an introduction to BMW cars: 1. Logo meaning: B.M.W. stands for Bavarian Motor Works, and the colors and combination of the logo come from the state emblem of Bavaria, where BMW is located. 2. Brand honors: On December 18, 2018, the "2018 World Brand 500" compiled by the World Brand Laboratory was announced, with BMW ranking 16th.

6

5

Share

How many days does it take for the newly replaced windshield to fully set?

Generally speaking, depending on the quality of the adhesive and seasonal factors, the windshield adhesive usually takes one to three days to fully dry. During this period when it's not completely dry, you can still drive, but extra caution is necessary. Additionally, avoid washing the car within three days after replacing the windshield, and remove the tape securing the windshield position after three days. Below are common reasons for spontaneous cracking of car windshields: 1. Heating and cooling: Spontaneous cracking of car windshields usually occurs at the edges, primarily due to the internal tensile stress and surface compressive stress generated during the laminated glass processing when heated and then cooled. These forces are stable when balanced but can lead to spontaneous cracking if unbalanced. 2. Sudden temperature changes: If the car glass is exposed to intense sunlight and then encounters cold water, the drastic temperature change can cause the glass to crack. If spontaneous cracking of the windshield occurs, pull over immediately and avoid continuing to drive. While minor cracks can be repaired, it is recommended to replace the windshield for safety reasons. 3. Improper installation: Windshield cracking can also result from improper installation, the use of substandard adhesive, or poor-quality heat-resistant film that absorbs heat instead of insulating it, leading to excessive temperature differences when the air conditioning is on inside the car.

5

1

Share

How to Match the Tire Pressure Monitoring System on Baojun 310?

What Causes the Engine Not to Start When the Water Temperature is High?

What Happens When You Press the Accelerator While in Park?

How to Convert Between Power and Horsepower?

What is the diameter of 700c wheels?

What is the 750 car?

How many days does it take for the newly replaced windshield to fully set?

What is the definition of first inspection?

Can a Flooded Car Be Repaired?

How long can a private car's annual inspection be overdue without penalty?

At what water level should you not drive your car?