How to manually reset the wrench light on a 2015 Fengshen AX7?

[CamilleDella]

Method to reset the maintenance wrench icon on Dongfeng Fengshen AX7: 1. When the maintenance light of Dongfeng Fengshen AX7 prompts for an oil change service, it's best not to reset it arbitrarily before servicing. You should go to a 4S shop for maintenance and use professional diagnostic equipment to reset it. 2. If maintenance has already been performed, you can reset it when the vehicle power is off (in P gear). Press and hold the left OK button on the steering wheel without stepping on the brake, then press the ignition button once. Wait for 10 seconds (during which the instrument panel will normally display "Please depress the brake pedal" - ignore this and continue holding OK). Then press the ignition button again, and when the instrument panel lights up, you'll see the wrench light has been reset.

[IsabelaMarie]

I remember last time the wrench light came on in my 2015 Fengshen AX7, which was actually the maintenance reminder light telling me it was time for an oil change. To manually reset it is quite simple: First, park the car and make sure the key is in the OFF position without starting the engine. Then, press and hold the TRIP button on the dashboard—the one used to toggle the fuel consumption display. Next, gently turn the key to the ON position, but don’t press the accelerator to start the engine. After a few seconds, the wrench light will start flashing. Wait about five seconds until it turns off, then release the TRIP button. The whole process takes just a minute or two, and I’ve tried it a few times myself—it’s quite reliable. However, never ignore this light, as it’s a warning that part wear could affect safety. I recommend resetting it promptly after maintenance, otherwise, it’ll be unsettling to drive, and a breakdown on the road would be troublesome. Also, keep track of maintenance dates and check fluids every 5,000 kilometers or so.

[Jackson]

It's not difficult to remove the wrench light on the Fengshen AX7. I consider it from a safety perspective: when this light comes on, it indicates that the vehicle needs maintenance. If not addressed promptly, fuel consumption may increase or parts may get damaged. The first step in manual operation is to find a flat area to park and turn off the engine, ensuring the ignition switch is in the OFF position. Then, press and hold the TRIP button on the left side of the dashboard without releasing it. Slowly turn the key to the ON position without starting the engine. At this point, the wrench light will usually flash a few times and then turn off. Maintain the press for about ten seconds throughout the process, and release the button only after the light disappears. Resetting it this way can avoid misjudging driving data. When I notice the light on while driving, I immediately pull over to handle it, ensuring it doesn't distract me and affect driving. Under normal maintenance reminders, you should regularly check the oil and filters to protect the engine's lifespan.

[JasperAnn]

The wrench light is the vehicle's built-in maintenance counter signal, which reminds you on the dashboard when the maintenance cycle is due. Here are the detailed steps for manual reset: First, turn off the engine and return the key to the OFF position. Press and hold the TRIP button, then turn the key to the ON position and wait. When the wrench light flashes, hold for five seconds until the light goes off, then release. This setting is calculated based on mileage, and resetting it restores the reminder system. It is recommended to perform this operation after maintenance to avoid delaying and preventing potential issues. The circuit is simple and won't harm the vehicle. Regular maintenance can also improve fuel efficiency.

[VonJohn]

Quick method to clear the wrench light on Fengshen AX7: After parking and turning off the engine, hold the TRIP button while turning the key to the ON position (do not start the engine), release when the light flashes and wait for it to go off. I often use this method to save time. However, make sure the maintenance has been completed, otherwise it's just self-deception. Regularly check the odometer to avoid exceeding the limit, and frequent oil changes can reduce the frequency of the light coming on. The steps are simple and safe, even beginners can handle it.

[MacBrooke]

The wrench light on the Fengshen AX7 is a maintenance indicator, and manual reset is a temporary measure. The procedure is: park and turn off the engine, hold the TRIP button in the OFF position, turn to ON without starting, release when the light flashes and goes off. This can resolve false alarms, but regular maintenance is the root solution. I typically inspect every six months to prevent issues and reduce manual resets. Ensure the operation is safe and straightforward; unfamiliar users can refer to the manual's diagrams. Consistent maintenance improves vehicle condition and longevity.