How to manually reset the maintenance light on the diesel Maxus V80?

1 Answers
DeAlex
07/29/25 7:50pm
Turn on the ignition while holding down the trip meter hour reset button. Here is some relevant information about the maintenance light: 1. Introduction: The maintenance light is a reminder function set by the manufacturer to notify the owner to perform maintenance at certain mileage or time intervals. It appears in the form of a dashboard or screen message or indicator light. Resetting the maintenance light means clearing the reminder information after maintenance is completed, which is essentially a reset of the information. 2. Purpose: The purpose of the maintenance light is to record the mileage of important components, similar to a timer in a sprint race, serving as a reminder for the owner and automotive repair personnel. If the owner replaces related components but does not reset the light, it will not affect the vehicle's performance, but it may cause inconvenience for the next component replacement, as the exact usage time of the new component cannot be accurately determined.
Was this review help?
2
4
Share
More Forum Discussions

Should Turn Signals Be Used on S-curves?

S-curves do not require the use of turn signals. Below are the relevant explanations: Reasons: For continuous S-curves, if there is a fork in the road, using a turn signal would be equivalent to informing all vehicles that you are entering the fork. S-curves may also have intersections, and large-radius S-curves on mountain roads or rural roads might involve pulling over to the side. At the same time, a right turn signal can easily be misinterpreted as slowing down to the right due to special circumstances, requiring a pause before overtaking. Operating Essentials: Before entering an S-curve, reduce your speed and enter in first or second gear, choosing an appropriate route and speed to navigate through. Once in the S-curve, keep the vehicle along the right side of the road (about 1 meter from the left edge) and maintain a steady, low speed. Maintain a distance of about 0.5 meters from the right side of the road, making slight directional adjustments as needed (leaving enough space for the inner wheel difference on the left).
20
3
Share

What is the reason for the DSTC SPORT light coming on?

It is because the sport mode that disables ESP has been enabled in the settings. If a "DSTC requires service" message appears, it means there is a fault in the ABS anti-lock braking system. Below are the specific details about the ABS system: Function of the ABS system: ABS is the vehicle's anti-lock braking system, which belongs to the active safety systems of a car. When the ABS light comes on, it indicates that the vehicle's computer has detected a fault in the ABS system. Reasons for the ABS light coming on: During normal driving, the ABS remains in a dormant state. It only activates during emergency braking, such as when braking hard at high speeds. The vehicle's computer determines when the ABS should intervene. When the ABS light comes on, it is often due to the wheel speed sensors not functioning properly. The ABS computer cannot detect the driving conditions of each wheel and cannot compare the slip amounts of the wheels, resulting in the ABS system failing to operate correctly.
14
4
Share

Should the heel move when correctly depressing the clutch?

Yes. Here are the relevant details: 1. Clutch operation method: Place the ball of your foot on the clutch pedal and press it all the way down. Keep it depressed and find the most comfortable position for the ball of your foot. Lift your leg while keeping the heel suspended, then slowly release the clutch. Note that you don't need heel support at this stage - keep the heel suspended to let your leg follow the clutch's spring force freely. When you feel the engine start to vibrate, stop releasing the clutch with the ball of your foot and quickly lower your heel. Remember this heel support position as it's precise and effective. 2. Introduction to the clutch: The clutch is located in the flywheel housing between the engine and transmission, with the clutch assembly fixed to the rear plane of the flywheel by screws. The output shaft of the clutch is the input shaft of the transmission. While driving, the driver can depress or release the clutch pedal as needed to temporarily separate or gradually engage the engine and transmission, thereby interrupting or transmitting power from the engine to the transmission. The clutch is a common component in mechanical transmission systems, allowing the drivetrain to be disconnected or connected as required.
2
2
Share

Will the car interior get flooded if the parked car is submerged in rainwater on the roadside?

If a car is parked on the roadside and gets submerged in rainwater, water may enter the interior. Below are specific symptoms indicating water ingress in vehicles: Abnormal engine oil condition: Normal engine oil colors include light yellow, brown, or transparent colorless, but it generally does not appear milky white. Pull out the dipstick to check for any milky oil-water mixture; if present, it might indicate engine water ingress. Inspect the air filter: Check the air filter and the lower housing for obvious signs of water ingress, and examine the intake pipe and intake manifold for clear traces of water. White smoke from the exhaust pipe: When there is water in the engine fuel or combustion chamber, the water is heated by the combustion heat in the cylinder, turning into steam that exits through the exhaust pipe as white smoke. If white smoke appears after the vehicle has driven through water, it is highly likely that the engine has taken in water.
9
0
Share

Can a Class C License Drive a Motorcycle?

No, a Class C license does not permit the operation of motorcycles. The types of Class C driver's licenses and their permitted vehicle categories are as follows: C1 (Small Cars): Permitted vehicles: Small and micro passenger cars, as well as light and micro cargo vehicles; light and micro special-purpose vehicles. C2 (Small Automatic Transmission Cars): Permitted vehicles: Small and micro automatic transmission passenger cars, as well as light and micro automatic transmission cargo vehicles. C3 (Low-Speed Cargo Vehicles): Permitted vehicles: Low-speed cargo vehicles. C4 (Three-Wheeled Vehicles): Permitted vehicles: Three-wheeled vehicles. C5 (Small Automatic Transmission Passenger Cars for Disabled Persons): Permitted vehicles: Small and micro automatic transmission passenger cars specifically for disabled persons (allowing individuals with left lower limb, right lower limb, or both lower limbs disabilities to drive).
13
0
Share

What are the evaluation criteria for the 2021 Subject 3 driving test?

Here are the detailed evaluation criteria for the 2021 Subject 3 driving test: Vehicle preparation: Failure to walk around the vehicle to inspect its appearance and surrounding environment results in disqualification; Not observing traffic conditions behind before opening the car door leads to disqualification. Starting off: Starting with insufficient brake air pressure results in disqualification; Starting with the door not fully closed leads to disqualification; Not observing interior and exterior rearview mirrors or turning head to check rear traffic conditions before starting results in disqualification. Straight-line driving: Inability to maintain steady direction control and straight-line movement leads to disqualification; Failure to promptly decelerate when encountering braking from the vehicle ahead results in disqualification; Not timely observing rear traffic conditions through mirrors deducts 10 points. Gear shifting operation: Failure to smoothly shift gears as instructed leads to disqualification; Mismatch between vehicle speed and gear position deducts 10 points.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.