How to manually reset the maintenance light on CS15?

1 Answers
MacKai
07/29/25 11:53pm
CS15's maintenance light has two reset modes: one is through a computer, and the other is manual. The manual reset method is very simple. Turn the ignition switch to the OFF position, press the DISP button for 3 seconds, then release it. Turn the ignition switch to the ON position again, and press the DISP button for another 3 seconds. The maintenance light will then reset and turn off. More related information is as follows: 1. The maintenance light serves as a reminder. When the vehicle reaches the specified mileage, the indicator light will remind the owner to perform maintenance or replace certain internal parts of the car. It also makes it easier for automotive repair personnel to check maintenance records, serving as an important indicator tool for the vehicle. 2. The air filter of the CS15 should be replaced every 10,000 kilometers, the cabin air filter every 10,000 kilometers, the brake fluid every 25,000 kilometers, the coolant every 35,000 kilometers, the spark plugs every 20,000 kilometers, and the transmission fluid is designed for lifetime maintenance-free use.
Was this review help?
17
4
Share
More Forum Discussions

What is the maintenance interval for the Volkswagen Golf?

The maintenance interval for the Volkswagen Golf is not fixed. If high-quality fully synthetic oil is used, the car can be serviced every 8,000 to 10,000 kilometers. If mineral oil is used, the maintenance interval should be every 5,000 kilometers. Below is an introduction to engine oil: 1. Engine oil is referred to as the "blood" of the engine, as it serves functions such as lubrication, cleaning, sealing, heat dissipation, buffering, and rust prevention. Without engine oil, the engine cannot operate properly. 2. During routine maintenance, changing the engine oil is a primary task. Every time the oil is replaced, the oil filter should also be changed. If the oil is not replaced for an extended period, it will oxidize and degrade, reducing its lubricating properties and accelerating engine wear. 3. When purchasing engine oil, it is essential to choose the appropriate viscosity. The viscosity should neither be too high nor too low. If the viscosity is too high, it will increase the engine's operating resistance, while if it is too low, it will accelerate engine wear. 4. During normal engine operation, the oil forms a protective film on the surfaces of various engine components, reducing friction between them. If the oil is not changed for a long time, it will fail to form a stable protective film, leading to increased engine wear. 5. When purchasing an oil filter, always opt for products from reputable brands.
1
2
Share

Is the Great Wall Pao 4WD?

The Great Wall Pao offers two types of drivetrain configurations: one is 2WD, and the other is 4WD. The 2WD version features a front-engine, rear-wheel-drive layout, while the 4WD version adopts a front-engine, four-wheel-drive system. The 4WD variant allows switching among three modes: 2WD, on-demand 4WD, and low-speed 4WD. Additionally, the rear axle is equipped with an Eaton differential lock. Although the 4WD system is an on-demand type, it is supplied by BorgWarner, ensuring excellent performance and reliability. The launch of the Great Wall Pao signifies that Great Wall Motors is fully committed to the pickup truck market. To cater to diverse user needs, the vehicle is available in three variants: Passenger Pickup, Commercial Pickup, and Off-Road Pickup.
11
2
Share

Is the Changan EADO equipped with a dual-clutch transmission?

Changan EADO does not use dual-clutch transmissions across its entire lineup. Only models equipped with turbocharged engines utilize dual-clutch transmissions, while those with naturally aspirated engines do not. The Changan EADO employs two types of engines: a 1.6-liter naturally aspirated engine and a 1.4-liter turbocharged engine. The EADO is a globally strategic sedan developed by Changan Automobile's international R&D team over three years, representing a high-end vehicle with international standards. On March 27, 2012, the domestic brand Changan Automobile announced the official launch of its new sedan, the EADO.
11
3
Share

What is the difference between direct injection and multi-point electronic injection?

The difference between direct injection and multi-point electronic injection lies in the fuel injection method: direct injection sprays fuel directly into the cylinder; multi-point electronic injection has injectors mounted on the intake manifold, where fuel and air begin to mix in the manifold before entering the cylinder. The engine generates power by burning fuel and air, and the fuel enters the cylinder through "injection." For electronic fuel injection engines, the key component is the fuel injector. If it becomes clogged, it can cause unstable idling, increased fuel consumption, poor acceleration, difficulty starting, excessive emissions, and in severe cases, completely block the injector, damaging the engine. If the injectors are installed on the intake pipe of each cylinder, meaning gasoline is injected from multiple locations (at least one injection point per cylinder), this is called multi-point electronic injection.
9
1
Share

Can You Still Drive with Brake System Failure?

You cannot continue driving with brake system failure. If the brake system malfunctions, it will affect driving safety, and you should promptly inspect and repair it. A car's brake system consists of a vacuum booster pump, master brake cylinder, wheel brake cylinder, brake pads, and brake discs. To ensure safe driving, improve the average driving speed, and enhance transportation productivity, dedicated braking mechanisms are installed on various vehicles. This series of specialized devices is collectively referred to as the brake system. The main functions of the brake system are to decelerate or even stop a moving vehicle, maintain a stable speed for a vehicle going downhill, and keep a parked vehicle stationary.
20
3
Share

What's the difference between Continental MC5 and MC6?

Continental MC6 differs from MC5 mainly in dry handling, mileage, wet handling, wet braking performance, dry braking performance, etc. Here are the specific details: Introduction: The Continental MC6 is the successor model to the MC5, which comprehensively improves handling and durability while maintaining the original noise and comfort levels. Tires: Tires are the medium for transmitting forces between the vehicle and the road surface, transferring driving force, braking force, steering force, etc., thereby enabling the vehicle's driving, braking, and steering operations. Supporting vehicle load: The vehicle's load causes the tire to sink until the average pressure of the tire's contact area balances with the internal inflation pressure.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.