How to manually reset the maintenance light of K3?

1 Answers
VonAdaline
07/30/25 3:12am
Steps to manually reset the maintenance light of the new Kia K3: 1. First, turn the power of the Kia K3 to ON mode. 2. Then press the toggle button on the steering wheel to switch to user settings, where you can see the maintenance settings. 3. Finally, enter the maintenance settings and long press the OK button to reset the maintenance mileage time. Below is some relevant information about the Kia K3: 1. The Kia K3 has attracted attention with its cutting-edge exterior and interior design. 2. In addition to design changes, the new generation K3 also features a new powertrain based on the Smartstream IVT architecture. The 1.5L high-efficiency engine it is equipped with has a combined fuel consumption of only 5.1L per 100km, achieving excellent fuel economy.
Was this review help?
18
2
Share
More Forum Discussions

What to Do When the Car Shows a Maintenance Reminder?

When the car shows a maintenance reminder, the solution is to perform the maintenance. The maintenance light on the car is a reminder function set by the manufacturer to notify the owner to perform maintenance at certain mileage or time intervals. It appears in the form of a dashboard or screen message or indicator light. Steps to reset the maintenance light: 1. With the engine off, press and hold the trip reset button located below the tachometer. 2. Turn the ignition to the ON position, then release the trip reset button. The display will show the "Service" indicator. 3. Pull out the minute button on the clock and turn it to the right. The mileage display will appear on the screen. 4. Turn off the engine to reset the reminder message. 5. Turn the ignition to the ON position again, and the "Service" indicator will disappear.
15
2
Share

Where is the cabin air filter located in an Audi A3?

The cabin air filter in an Audi A3 is located inside the glove compartment on the passenger side. The replacement method is as follows: 1. Open the passenger-side storage compartment and release the cover clips; 2. Pull out the old cabin air filter and install the new one. Taking the 2021 Audi A3 as an example, its body dimensions are: length 4351mm, width 1815mm, height 1458mm, with a wheelbase of 2630mm and a fuel tank capacity of 51 liters. The 2021 Audi A3 is equipped with a 1.4T turbocharged engine, delivering a maximum power of 110kW and a maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission.
15
4
Share

How to Replace the Battery in a Mercedes-Benz E55 Key?

Mercedes-Benz E55 key battery replacement method is: 1. Press the button on the back of the key; 2. Push the back cover of the key forward to open it and remove the old battery; 3. Install the new battery and reattach the key cover. The Mercedes-Benz E55 has the following dimensions: length 4818mm, width 1822mm, height 1452mm, with a wheelbase of 2854mm, a fuel tank capacity of 80 liters, and a curb weight of 1835kg. The Mercedes-Benz E55 is equipped with a 5.5-liter V8 engine, delivering a maximum power of 200kw and a maximum torque of 700nm, paired with a 5-speed automatic transmission.
10
0
Share

How far can a G63 go on a full tank of gas?

G63 can travel about 500 kilometers on a full tank of gas. The Mercedes-Benz G63 is an off-road vehicle launched by Mercedes-Benz, featuring a very distinctive design with high recognition. Below is a related introduction to the Mercedes-Benz G63: 1. Exterior: This vehicle retains the classic box-shaped design that has been continued for 39 years, with the upgraded model only making changes in details, giving the overall appearance a very sporty look. To reduce the vehicle's weight, it adopts a lightweight design, which not only reduces the car's weight but also enhances the body's rigidity. 2. Performance: This vehicle is equipped with a 5.5L V8 engine, which delivers a maximum power of 544 horsepower and a maximum torque of 760 Nm. According to official information, the car accelerates from 0-100km/h in 5.4 seconds, with a top speed of 210km/h.
16
0
Share

What Causes the Engine Light to Suddenly Illuminate?

The reasons for the engine light suddenly illuminating are: 1. Faulty coolant temperature sensor, crankshaft sensor, or oxygen sensor; 2. Spark plug failure; 3. Ignition coil malfunction; 4. Fuel pump failure; 5. Fuel line blockage; 6. Poor engine combustion state; 7. Blown main circuit fuse. Composition of the engine: 1. Engine block group: cylinder head, cylinder block, and crankcase; 2. Crankshaft connecting rod mechanism: piston, connecting rod, crankshaft, flywheel; 3. Valve train and intake/exhaust system: intake valve, exhaust valve, tappet, push rod, rocker arm, camshaft, and camshaft timing gear; 4. Fuel supply system and governor: fuel tank, sediment cup, diesel filter, fuel transfer pump, fuel injection pump, and governor; 5. Starting device: clutch mechanism, flywheel ring gear, starter switch, battery.
15
0
Share

How to set the automatic locking function for the Honda Avancier?

The method to set the automatic locking function for the Honda Avancier is to press and hold the lock button for 6 seconds until the security indicator flashes twice. The purpose of the automatic locking function is anti-theft. The doors will automatically lock when the vehicle reaches a certain speed after starting, preventing door-pull robberies during traffic jams or at red lights, providing a certain level of security. Taking the 2020 Honda Avancier as an example, its body structure is a 5-door, 5-seat SUV with dimensions of length 4858mm, width 1942mm, height 1670mm, and a wheelbase of 2820mm. It has a fuel tank capacity of 57 liters, a trunk capacity of 510 liters, and a curb weight of 1801kg.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.