How to Maintain Bridgestone Tires?

1 Answers
LeEzra
07/30/25 7:06am
Bridgestone tire maintenance methods: 1. Rotate tire positions every 10,000 kilometers to evenly distribute tire fatigue, avoid uneven wear, and extend tire life; 2. When driving, avoid rapid starts, emergency braking, or sharp turns; 3. It is recommended to perform a wheel alignment every 2,000 kilometers to reduce abnormal tire wear caused by changes in the main parameters of wheel alignment. Bridgestone tires are products of Bridgestone Corporation of Japan and are now widely used in various automobile brands worldwide. Bridgestone tires are currently used in products of several Chinese automobile manufacturers, including Guangzhou Honda, Tianjin FAW Toyota, Zhengzhou Nissan, and Beijing Jeep.
Was this review help?
7
5
Share
More Forum Discussions

Why does the car air conditioner cool slowly after being exposed to the sun?

The reason why the car air conditioner cools slowly after being exposed to the sun is that the compressor protection device trips. Here is more relevant information: 1. Reasons and solutions for high pressure and overheating: (1) Too much refrigerant. Appropriately reduce the amount of refrigerant. (2) Poor heat dissipation. Check if the condenser tube is dirty and clean the condenser. (3) Blockage in the pipeline system. Refer to the pressure gauge to judge and eliminate, then reprocess the system. (4) Dust and scale accumulation on the evaporator or filter. The airflow becomes smaller, and the system pressure and temperature become unbalanced. Clean the evaporator or filter. (5) Lack of fluorine is also possible. When there is a lack of fluorine, the compressor exhaust temperature will overheat, causing the overload protection switch to trip. 2. Problems with the circuit: (1) Control circuit board failure. (2) Temperature sensor overload, incorrect information. (3) Loose or poor contact of power wiring. (4) The starting capacitor or compressor starting coil is burnt out.
5
0
Share

How to distinguish between entrance markings and exit markings on roads?

Road entrance markings and exit markings are different in nature. The differences between road entrance markings and exit markings are as follows: 1. Characteristics of road exit markings: Road traffic markings are mainly painted on the road surface and are exposed to sun, rain, snow, ice, and vehicle impact and wear, so they have strict performance requirements. They must have a short drying time and be simple to operate to minimize traffic disruption. Secondly, they must have strong reflectivity, bright colors, and high reflectivity to ensure good visibility both day and night. Thirdly, they must have anti-slip and wear-resistant properties to ensure driving safety and longevity. 2. Characteristics of road exit deceleration markings: The longitudinal deceleration markings for vehicle lanes consist of a series of diamond-shaped dashed lines parallel to the lane dividing lines. They are usually installed at bridge approaches and turns, primarily to create a visual narrowing of the lane, inducing a sense of pressure that prompts drivers to automatically slow down at curves, slopes, and other locations where deceleration is required. Whether lane changes are permitted under deceleration markings depends on the state of the markings beside them. If the markings are solid lines, lane changes are not allowed; if they are dashed lines, lane changes are permitted.
4
4
Share

What to Do When the Side Windows Fog Up?

Just prepare a towel with good moisture absorption and gently wipe the windows. Here are some related methods to remove window fogging: 1. Open the windows: Crack the windows slightly to allow air convection, using negative pressure to draw out the fog. If there is a sunroof, open it and use the rear tilt function to quickly expel the air. 2. Use the car's front defroster mode to quickly restore the windows to normal. 3. Use anti-fog spray: In fact, many anti-fog sprays work very well—just spray the anti-fog agent on the glass surface in advance.
8
0
Share

How to unlock the car from outside when the key is locked inside?

If the car key is locked inside the car, first try to find a spare key. If there is no spare key, contact a qualified locksmith company to unlock the car. Here is more relevant information: 1. Use a mobile phone remote control to unlock: However, to use this method, you need to install a car cloud key system on your phone. Additionally, this method cannot be used in areas with poor signal or where the signal is interfered with. 2. Use the car battery to open the door: This method is not suitable for all car models. It involves using a small metal piece to touch the positive terminal of the battery to open the door. When touching the battery with the small metal piece, be sure to wear insulated gloves to avoid electric shock. If none of the above four methods successfully unlock the car, you may have to resort to breaking a window to unlock it.
9
4
Share

How many years of driving experience are required for car rental?

There is no restriction on the years of driving experience for driving a taxi, but a taxi driver's qualification certificate is required. Below is more relevant information: 1. Materials required for applying for a taxi driver's work permit: (1) The applicant's professional qualification certificate (original and one copy). (2) Notification of public security license issuance (issued by the Municipal Public Transport Bureau Taxi Management Office). (3) One photo of the driver, with the vehicle number and name written on the back. (4) Work permit registration form, stamped with the company's official seal. 2. Materials to be submitted by the applicant: (1) Motor vehicle driver's license (copy). (2) ID card (copy). (3) Proof from the taxi company (if there is no proof from a taxi company, the applicant can participate in training and examination, and upon passing, a vocational training certificate will be issued. The professional qualification certificate can be obtained after securing a job). (4) Two 1-inch and one 2-inch color recent photos.
5
3
Share

What are the reasons for both high and low beams of car headlights not working?

The reasons for both high and low beams of car headlights not working may be a blown fuse or burnt-out bulb. Below are some precautions regarding car headlight maintenance: 1. Maintain sealing: Moisture intrusion can reduce the lifespan of the bulb, so it is important to check the sealing of the headlights. 2. Keep clean: Clean the reflector; if the reflector of a semi-sealed headlight turns black and the light intensity decreases, it should be replaced. If the reflector is silver-plated or aluminum-plated, due to its lower hardness, only clean cotton soaked in hot water should be used for cleaning, and never wipe it to avoid damaging the reflector coating. Clean the bulb: When there is dust or dirt on a halogen bulb, use degreasing cotton soaked in ethanol (90%) to wipe it.
12
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.