How to Locate the Fuel Filter in Mercedes-Benz GLA?

2 Answers
RhettLee
07/29/25 12:56am
The fuel filter is located near the fuel tank at the rear underside of the vehicle, and the model number of the fuel filter is GLA45. Below is relevant information about Mercedes-Benz fuel filters: 1. The filter element of the fuel filter mostly uses filter paper, and some fuel filters use nylon cloth or polymer materials. The main function is to filter out impurities in the gasoline. 2. The role of the fuel filter is to remove water and impurities from the gasoline. Below is relevant information about replacing the filter: 1. First, remove the vehicle key and disconnect the fuel pump fuse or the vehicle power supply to prevent the fuel pump from pumping out gasoline during disassembly. 2. Next, remove the rear seat cushion and the cover on the fuel pump, at which point you can see the fuel pump assembly. 3. The fuel pump assembly is secured by a black retaining ring. After disconnecting the wiring harness and fuel lines on the fuel pump, a special tool is required to remove this retaining ring. 4. After removing the retaining ring, the fuel pump assembly can be taken out. Replace the corresponding components of the old fuel filter with the new fuel filter assembly.
Was this review help?
6
0
Share
OEdward
08/12/25 5:07am
I've replaced the fuel filter on my Mercedes-Benz GLA several times. It's usually built into the fuel tank, so you'll need to lift the vehicle or find a safe spot to check underneath. The fuel tank is located beneath the rear of the car, and the filter is connected to the fuel pump module, requiring you to pry open the access cover. The steps involve first disconnecting the battery's negative terminal to avoid sparks, then cleaning the surrounding area, using a wrench to remove the fuel lines and electrical connectors, and preparing a container to catch any spilled gasoline. The whole process takes at least an hour, with special attention needed to differences in model years—my 2018 model has the filter directly visible under the trunk's floor cover. It's recommended to replace it every 60,000 kilometers to prevent fuel system clogs that could affect starting. Before starting, it's best to consult the owner's manual or watch professional tutorial videos.
Was this review help?
11
2
Share
Expand All
More Forum Discussions

How to Determine if a Car is Burning Oil?

Methods to determine if a car is burning oil are as follows: 1. Check the exhaust pipe during cold starts. In the early morning after starting the vehicle, you can step out and observe if there is any blue smoke coming from the exhaust pipe. If there is slight blue smoke, it indicates a possibility of oil burning. 2. Observe the exhaust during acceleration. While driving or idling, if you press the accelerator hard and notice a large amount of blue smoke from the exhaust pipe, it suggests that the engine is burning oil. 3. Monitor oil consumption. Regularly check the oil dipstick to assess oil consumption and determine if oil is being burned. If you notice that the oil is being consumed significantly faster than usual before the scheduled maintenance date, it is important to address the issue promptly.
15
5
Share

Are Off-Road Vehicles SUVs?

Off-road vehicles are not SUVs. The main differences between off-road vehicles and SUVs are as follows: 1. Different body structures. (1) Off-road vehicles adopt a non-load-bearing body structure similar to trucks. (2) SUVs adopt the same load-bearing body structure as sedans. 2. Different suspension structures. (1) Off-road vehicles mostly use double-wishbone independent suspension. (2) SUVs mostly use MacPherson suspension systems. 3. Different four-wheel drive systems. (1) Off-road vehicles must have a four-wheel drive system, whether it's full-time four-wheel drive or part-time four-wheel drive. (2) SUVs are mainly used in urban or suburban environments and do not necessarily require four-wheel drive. In many SUV models on the market, some only offer four-wheel drive in high-end configurations, and some even do not have four-wheel drive across the entire series.
2
5
Share

Is it okay to shift to neutral at a red light with an automatic transmission?

For automatic transmission vehicles waiting at a red light, the appropriate gear to shift into depends on the duration of the red light. The recommended shifting practices are as follows: 1. If the red light is less than 30 seconds, it is recommended that the driver simply keep their foot on the brake. 2. If the red light lasts between 30 seconds and 1 minute, the driver should shift to N (Neutral) gear + handbrake. 3. For red lights longer than one minute, it is recommended to directly shift to P (Park) gear + handbrake. Below are the meanings represented by the letters on an automatic transmission: 1. P stands for Park. 2. R stands for Reverse. 3. N stands for Neutral. 4. D stands for Drive. 5. S stands for Sport. 6. L stands for Low. 7. M stands for Manual.
18
3
Share

How to Tell When Car Brake Pads Need Replacement

Here are several indicators to determine if your car's brake pads need replacement: 1. The dashboard has a brake pad wear limit warning light; when illuminated, it indicates the pads should be replaced. 2. The thickness of brake pads typically ranges between 1-1.5cm (varies by manufacturer). When worn down to less than 3mm, replacement is necessary. Most brake pads have wear limit indicators. 3. If the brake pedal travels deeper than usual (increased braking distance) or feels softer, the pads may be nearing the end of their life. Modern brakes are self-adjusting, so increased pedal travel naturally occurs as pads wear. 4. Reduced brake fluid level in the reservoir. As pads wear, the gap between disc and pad increases. After automatic adjustment, the caliper pistons extend outward, requiring additional brake fluid - thus reducing reservoir levels. 5. Squealing or metallic scraping sounds during braking suggest metal-to-metal contact between pad and disc, signaling immediate replacement is needed.
18
4
Share

Is an annual inspection required for B2 license?

B2 license requires an annual inspection. According to regulations, a B2 driver's license must be inspected once a year. However, if there are no demerit points recorded within a scoring cycle, the inspection for that cycle is exempted. The B2 driver's license undergoes an annual inspection, which must be completed within 30 days after the end of the current scoring cycle at the vehicle management office where the license was issued. Below is relevant information about driver's licenses: 1. B1 vehicle type: Medium-sized passenger vehicle. Permitted vehicles include medium-sized passenger cars. Other permitted vehicle types include C1, C2, C3, C4, and M. 2. B2 vehicle type: Large truck. Permitted vehicles include heavy and medium-duty trucks; heavy and medium-duty special purpose vehicles. Other permitted vehicle types include C1, C2, C3, C4, and M.
1
1
Share

What does the teapot symbol on the dashboard mean?

A teapot symbol illuminated on the car dashboard indicates the engine oil pressure warning light. Here are the reasons why the oil pressure warning light may stay on: 1. Insufficient lubricating oil in the oil pan, unsuitable lubricating oil grade, or too low viscosity; poor anti-foaming performance of the lubricating oil, causing air to mix into the oil circuit; 2. The oil pump diaphragm is broken, allowing gasoline to leak into the oil pan, or due to a damaged cylinder head gasket or cracked liner, cooling water leaks into the oil pan, diluting the lubricating oil. Here is more information: The main reason the oil pressure warning light comes on is insufficient engine oil pressure. The most common cause of engine oil pressure failure is insufficient oil volume. If the oil volume is insufficient, the oil pump's pumping volume decreases or fails to pump oil due to air entering, leading to a drop in oil pressure. The crankshaft and bearings, as well as the cylinder liner and piston, will experience accelerated wear due to poor lubrication.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.