How to Lift Up the Wiper Blades on a Volkswagen?

2 Answers
Wendy
07/25/25 1:13am
Method to lift the wiper blades on a Volkswagen: Turn off the engine, and within 10 seconds, activate the windshield washer switch. The wiper blades will automatically move to the middle position of the windshield. Then, hold the wiper blade mounting bracket with your hand and lift it up to raise the wiper blades. Below is a brief introduction about wiper blades: 1. Function: The wiper assembly includes components such as the motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly. It is a device used to remove raindrops and dust adhering to the vehicle's windshield. Proper use of wiper blades can enhance driving safety and improve vehicle visibility. 2. Power source: The power for the wiper blades comes from the motor, which is the core of the wiper system. The wiper motor, installed on the front windshield, is usually integrated with the worm gear mechanism. It converts continuous rotational motion into a left-right oscillating motion through the four-bar linkage to clean the windshield.
Was this review help?
9
1
Share
Jan
08/10/25 4:02pm
When I used to drive a Volkswagen Golf, I had to lift the wipers in winter to prevent freezing, and the steps were quite simple. After turning off the car, turn the key to the ACC position, or ensure the engine is completely off, then push the wiper switch to the wash position for about one or two seconds—it will automatically move to the middle and stop. At this point, you can gently lift the wiper arms manually without touching the glass. Don’t forget to regularly check if the wiper blades are worn after lifting them; otherwise, frozen ice on the windshield can be really annoying. I always take this opportunity to clear any leaf debris on the glass, ensuring better visibility and safety for the next drive. Doing this gives me peace of mind, especially in northern winters where temperatures drop below minus ten degrees Celsius—protecting the wipers means protecting driving visibility. I recommend doing this early before the weather gets too cold, rather than rushing when a snowstorm hits.
Was this review help?
5
0
Share
Expand All
More Forum Discussions

How to Remove BMW Mirror Glass?

Method to remove BMW mirror glass: First, you need to remove the inner door panel, take off the trim panel, unscrew the three screws securing the mirror, disconnect the mirror wiring plug, and then you can remove the mirror glass. The car mirror reflects the conditions behind, beside, and below the vehicle, allowing the driver to indirectly see these areas clearly and expanding the driver's field of vision. The BMW X3 is an SUV model under BMW, with body dimensions of 4648mm in length, 1881mm in width, and 1661mm in height, and a wheelbase of 2810mm. In terms of appearance, the BMW X3 has a bold and stylish design, with a more sporty double-kidney front grille. The blackened air intake grille, paired with exquisite chrome trim strips, adds more layers to the front face of the vehicle.
6
0
Share

Where to Get a Replacement Car Key When Lost?

When a car key is lost, there are generally two methods to get a replacement: one is to go directly to a car 4S dealership, and the other is to visit an auto parts market. Below is more related information: 1. Differences between going to a 4S dealership and an auto parts market: The biggest difference between going to a 4S dealership and an auto parts market is the price. At a 4S dealership, even an ordinary key can cost several hundred to over a thousand yuan, and some high-end keys may even cost tens of thousands. In contrast, the auto parts market has a price advantage, typically costing at least half the price of a 4S dealership. 2. Getting a key at a 4S dealership is more reliable: However, price isn't the only factor to consider; the method of operation is also important. A 4S dealership creates a brand-new smart car key. The lost key's code is invalidated in the system, and a new code is generated and activated. This method is safer because even if someone finds the lost key, it will no longer work to unlock the car. On the other hand, the auto parts market uses a method of cracking to create a key identical to the lost one. While this key can unlock the car and start the engine, there is a risk: if someone else finds the lost key, they can still use it to open the car. Therefore, it is recommended to go to a 4S dealership for a replacement key. Although the price is higher, it is more reliable and eliminates safety risks.
8
2
Share

How to Turn on the Heating in a Car's Air Conditioning System?

Method to turn on the heating in a car's air conditioning system: After starting the car, wait approximately 8 to 15 minutes until the water temperature rises to the normal level. At this point, you can turn on the heating. Adjust the air conditioning circulation mode to the internal circulation and switch to the heating mode. Some cars indicate this with a red zone, while others use a sun symbol. Additionally, do not turn on the AC switch. When the car is first started, the engine oil needs some time to lubricate all components. If you turn on the heating at this time, the insufficient internal lubrication of the engine will increase friction resistance, leading to higher engine load and inevitably higher fuel consumption. However, many people mistakenly blame the heating for this. The correct approach is to wait for a while after starting the car until the water temperature rises before turning on the heating.
6
3
Share

How many kilometers should the Mercedes-Benz C-Class fuel filter be replaced?

Mercedes-Benz C-Class fuel filter should be replaced approximately every 50,000 kilometers. Main functions of the fuel filter: Filter impurities in gasoline, remove impurities and moisture from the fuel, improve the cleanliness of gasoline, and prevent impurities from entering the fuel system and affecting the injection system. As long as the fuel added is clean, the filter can be used for a long time without issues. Classification of fuel filters: Fuel filters come in two types: built-in and external. The external filter has an iron shell with filter paper inside to filter impurities. The external filter has a relatively short service life and should be replaced around 50,000 kilometers. The built-in filter (used in most Mercedes-Benz vehicles today) is more difficult to remove, so it is designed with a large-capacity, long-lasting filter material. The built-in filter is recommended to be replaced around 100,000 kilometers. Working principles of built-in and external filters: The working principle of the built-in filter is completely different from that of the external filter. The external filter is located after the fuel pump, where the fuel output by the pump passes through the filter paper inside the external filter under pressure. The built-in filter is placed at the input end of the fuel pump, where the fuel is filtered by the filter material inside the filter screen before entering the fuel pump. This filter material has a large volume and high filtration capacity, resulting in a relatively longer service life. Symptoms of a clogged fuel filter: Weak acceleration and noticeable power loss when the car is fully loaded. Severe engine vibration at idle. Difficulty starting or inability to start the car.
18
0
Share

How to Disassemble a Prado Key?

Steps to disassemble a Prado key: 1. First, remove the protective cover or casing from the key; 2. Press the mechanical key button and pull out the mechanical key; 3. Then, pry open the rear cover clip at the head end, followed by the rear cover clip on the curved side, allowing you to remove the rear cover and complete the key disassembly. The Prado is equipped with a 5-speed automatic transmission and features a 5-door, 7-seat SUV body structure. In terms of interior, apart from the wood grain trim, the dashboard is also adorned with silver faux-metal materials, showcasing exceptional quality and craftsmanship in both texture and assembly. Regarding dimensions, the vehicle measures 4780mm in length, 1885mm in width, and 1845mm in height, with a wheelbase of 2790mm.
16
1
Share

What are the Toyota commercial seven-seater models?

Toyota commercial seven-seater models currently include MPV, E'Z, Alphard, Previa, Sienna, Hiace, SUV, Prado, Land Cruiser, Sequoia, and Highlander. Among them, the 2019 new Toyota Alphard appears more streamlined from the side, with an automatically opening sliding door being a major highlight, which can be operated simply by pulling the handle, making it an outstanding MPV. The Toyota E'Z is equipped with three engines: a 1.6-liter naturally aspirated engine, a 1.8-liter naturally aspirated engine, and a 2.0-liter naturally aspirated engine. In terms of body dimensions, the car measures 4450mm in length, 1790mm in width, 1640mm in height, with a wheelbase of 2780mm.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.