···
Log in / Register

How to Lift Up the Rear Seat of the X-Trail?

3 Answers
DeClara
07/29/25 9:50pm
The method to lift up the rear seat of the X-Trail is to firmly pull up the rear seats located on both sides near the rear doors, then secure the fasteners. Taking the 2021 X-Trail Fashion Edition as an example, its body dimensions are: length 4675mm, width 1820mm, height 1722mm, with a wheelbase of 2706mm and a fuel tank capacity of 65 liters. The 2021 X-Trail Fashion Edition features a front MacPherson strut independent suspension and a rear multi-link independent suspension. It is equipped with a 2.0L naturally aspirated engine, delivering a maximum horsepower of 151PS, a maximum power of 111kW, and a maximum torque of 194Nm, paired with a 7-speed continuously variable transmission.
Was this review help?
7
4
Share
Dawson
08/15/25 9:26pm
I've been driving the X-Trail for several years, and lifting the rear seat is part of routine maintenance. The operation isn't difficult. First, ensure the car is parked on a flat and safe surface, and turn off the engine to avoid accidental operations. Squat in front of the rear seat, reach under the front edge of the seat, where there are usually hidden pull rings or small straps on both sides. Gently pull with slight force, and you'll feel the front part unlock. Then, slowly lift the front edge of the seat upwards, and the entire seat can be flipped up to reveal the lower trunk space. If you need to completely remove it, be aware that there might be clips or buttons at the rear—release them to take the seat off. I do this cleaning once a month to prevent dust accumulation from damaging electrical wiring. Remember to wear gloves to protect your hands, especially since the latches might be tighter in a new car. After lifting, check for any debris to keep the interior tidy and extend its lifespan.
Was this review help?
6
2
Share
Expand All
VonFrancisco
10/17/25 6:09am
As a family SUV user, I prioritize practicality and safety. The method to lift the rear seats of the X-Trail is quite straightforward: After the vehicle is stationary, bend down into the back row, locate the small pull tab or lever at the bottom front of the seat with both hands, and pull it evenly until you hear a click, indicating the front lock is released. Then, support the front part of the seat and lift it to a certain angle to secure it. During the process, be mindful of the surroundings to prevent children or pets from getting close and avoid pinching injuries. Placing a protective mat can also help safeguard the interior. I usually take this opportunity to clean small debris under the seats or rearrange items, as the flexible space is convenient for daily large purchases. After lifting, always double-check that the seat is securely latched before driving—safety is no small matter.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

How to Adjust the Seats in a Passat?

Passat seat adjustment methods: divided into electric adjustment and manual adjustment. Electric adjustment involves a small module shaped like a seat on the left side of the seat; pushing it up, down, forward, or backward as needed can help you find a comfortable position. Manual adjustment includes a pull-up handle located under the seat on the right side for forward and backward movement—lift it and push the seat to adjust. For seat cushion height adjustment, there is a lift-up and push-down armrest on the left side of the seat to adjust the height. The Passat is equipped with a 1.4T inline 4-cylinder turbocharged engine, delivering a maximum horsepower of 150 PS, a maximum torque of 250 Nm, and a maximum power of 110 kW. The front suspension of this car is a MacPherson strut independent suspension, and the rear suspension is a multi-link independent suspension.
14
0
Share

What are the components of a wheel structure?

Wheels are typically composed of a rim and spokes. The rim is the component that mounts and supports the tire on the wheel, while the spokes are the supporting components between the axle and the rim on the wheel. In addition to these components, wheels sometimes also include a hub. The rim is the part that mounts and supports the tire around the circumference of the wheel, forming the wheel together with the spokes. The rim and spokes can be integral, permanently connected, or detachable. The spokes are devices that protect the wheel rim and spokes of a vehicle's wheel, characterized by a pair of circular cover plates with diameters similar to that of the wheel rim. Based on the structure of the spokes, wheels are divided into disc-type and spoke-type. Currently, mainstream family cars mostly adopt disc-type spoke structures. The hub is a cylindrical metal component that supports the tire within its inner contour and is mounted centrally on the axle. It is also known as the wheel rim, steel rim, or wheel disc. Hubs come in a wide variety of types based on diameter, width, forming method, and material.
10
3
Share

What is the function of the oil pressure gauge?

The function of the oil pressure gauge is to detect and display the oil pressure in the engine's main oil passage to prevent major failures such as cylinder scuffing and bearing burning due to insufficient oil. The oil pressure gauge is used to indicate the oil pressure in the engine, allowing you to understand whether the engine lubrication system is working properly. It consists of an oil pressure sensor installed on the engine's main oil passage and an oil pressure indicator on the instrument panel. Commonly used oil pressure gauges include bimetallic, electromagnetic, and moving-magnet types, with the bimetallic type being the most widely used. Precautions for using the oil pressure gauge: The oil pressure gauge must be used with its matching voltage regulator and sensor; during installation, ensure good insulation of the terminals and avoid striking during disassembly; for spring-tube type oil pressure gauges, ensure the sealing of the pipe opening to prevent oil leakage. How to use the oil pressure gauge: Park the vehicle on a level surface and wait long enough (2-3 minutes) for the oil to drain back and check if the oil level is too low. Add the recommended grade of engine oil to the crankcase until the oil level reaches the "FULL" mark on the dipstick. Start the engine and confirm that the vehicle's pressure gauge or warning light does not indicate low or no oil pressure. Remove the oil pressure sensor or another engine block oil passage plug.
18
4
Share

What is the fuel tank capacity of the 2016 Elantra?

2016 Elantra has 4 models with a fuel tank capacity of 50 liters. The vehicle is equipped with a 1.6L naturally aspirated engine, and all models use a 6-speed automatic transmission (AT) or a 6-speed manual transmission (MT). Among vehicles in the same class, the 2022 Lavida has a fuel tank capacity of 51 liters, the 2021 Xingrui has a 50-liter tank, and the 2021 Corolla also has a 50-liter tank. During actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity marked by car manufacturers is measured from the bottom of the tank to the safety level, and there is still some space from the safety level to the tank opening. This space is reserved to allow fuel expansion when temperatures rise, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual refueling amount may exceed the calibrated tank capacity. To check the remaining fuel level, drivers can observe the fuel gauge on the right side of the instrument panel, which is marked with E and F. When the pointer is near E, it indicates low fuel, and when it is close to F, it means the fuel level is sufficient.
2
2
Share

What Causes the Fault Light to Illuminate in the Baojun 730?

The reasons for the engine fault light illuminating in the Baojun 730 include a damaged oxygen sensor, a faulty three-way catalytic converter, or the need to tighten or replace the fuel tank cap. Oxygen Sensor Replacement Needed: The oxygen sensor is crucial for both engine performance and environmental protection. It measures the amount of unburned oxygen in the exhaust to determine if the vehicle's fuel-air mixture is at its optimal state. There are many reasons for oxygen sensor failure, such as not changing the engine oil regularly or failing to clean impurities from the coolant in the engine promptly. If the oxygen sensor fails, fuel consumption may increase by more than 40% compared to normal levels. Three-Way Catalytic Converter Replacement Needed: The three-way catalytic converter usually doesn't encounter issues, but if problems with the spark plugs, ignition coils, or engine mechanical faults are not properly addressed, they can damage the three-way catalytic converter. Tightening or Replacing the Fuel Tank Cap Needed: According to statistics, issues with the fuel tank cap account for 7.1% of vehicle fault investigations in a year, which is not a small probability. If the fuel tank cap is lost or damaged, it can waste both time and money, and of course, the engine fault light will also illuminate. Problems with the fuel tank cap may lead to increased fuel consumption and environmental damage.
18
1
Share

Will an Air-Cooled Motorcycle Overheat on Long-Distance Rides?

An air-cooled motorcycle will not overheat on long-distance rides. Air-cooled motorcycles rely on natural wind during riding to force engine cooling, so as long as the motorcycle maintains a certain speed, it can achieve automatic heat dissipation. Theoretically, because the cooling method of air-cooled motorcycles is relatively traditional, their performance will sharply decrease after prolonged, uninterrupted riding. However, in reality, as long as the engine speed is controlled throughout the entire ride, its cooling method is fully capable of adapting to normal riding conditions. More information about air-cooled motorcycles is as follows: 1. Engine Speed: When the engine speed is too high, it will affect the cooling effect, especially during long-distance rides, where high speed directly determines the current cooling efficiency of the vehicle. Factors directly related to engine speed include driving habits, road conditions, and engine characteristics. 2. Steady-Speed Riding: During long-distance rides on an air-cooled motorcycle, the vehicle's condition mainly depends on the current riding state. Aggressive riding will require more frequent breaks and shorter distances, while steady-speed riding can appropriately extend the distance. Therefore, under the premise of the same total distance, steady-speed riding saves more time compared to aggressive riding and is also more beneficial for both the vehicle and the rider.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.