How to Lift the Wiper Blade Up?

Is the Mercedes-Benz V-Class a domestically produced car?

Mercedes-Benz's V-Class is a domestically produced car, manufactured by Fujian Mercedes-Benz. Below is an introduction to the Mercedes-Benz V-Class: 1. The Mercedes-Benz V-Class is equipped with a 2.0-liter turbocharged engine across the entire lineup. This engine has a maximum power of 155 kW, a maximum torque of 350 Nm, a maximum power speed of 5500 rpm, and a maximum torque speed range of 1250 to 4000 rpm. The engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. 2. Paired with this engine is a 7-speed automatic manual transmission. The front suspension of the V-Class uses a MacPherson independent suspension, while the rear suspension uses a semi-trailing arm independent suspension. 3. The body dimensions are 5140mm in length, 1928mm in width, and 1880mm in height, with a wheelbase of 3200mm.

13

5

Share

How to Install a Beam Wiper Blade?

Beam wiper blades are composed of four components: the wiper rubber strip, the beam wiper steel strip, the wiper cover, and plastic parts. The bracket is made of stainless steel, while the steel strip is made of carbon steel, with a length ranging between 10-28 inches, a thickness of 0.80~0.90 millimeters, and a width generally between 7.00~14.00 millimeters. The installation steps for a beam wiper blade are as follows: 1. First, lift the old wiper blade and take the opportunity to wipe off any dust on the car. 2. The wiper blade and the U-shaped arm must form a 90-degree angle to remove the wiper blade. 3. Once the old wiper blade is removed, install the new beam wiper blade. Gently press the "buttons" on both sides with your fingers, and the middle cover will open. 4. Then, insert the U-shaped arm, lock it in place, press the cover back down, and smooth it out. 5. The beam wiper blade installation is now complete.

19

3

Share

Are Transmission Fluid and Power Steering Fluid the Same?

Transmission fluid and power steering fluid are not the same. Here are the specific details about these two fluids: 1. Transmission fluid can be added to the power steering pump, but power steering fluid cannot be added to the transmission as it does not meet the required specifications. 2. Power steering fluid is a special liquid used in the car's power steering pump. Through hydraulic action, it makes the steering wheel very light, similar to automatic transmission fluid, brake fluid, and shock absorber fluid. 3. Automatic Transmission Fluid (ATF) is specifically designed for automatic transmissions. Early automatic transmissions did not have dedicated fluid and instead used engine oil as a substitute.

11

1

Share

Where is the Nissan Sunny OBD interface located?

The OBD interface of the Nissan Sunny is located under the steering wheel cover. Here is some information about the OBD system: 1. OBD is a detection system extended for automotive fault diagnosis. 2. The OBD system continuously monitors the engine's operating conditions to check if the vehicle's exhaust exceeds the standard. If it does, it will immediately issue a warning. Additional information: 1. Exterior design. The Sunny inherits Nissan's family-oriented design approach, with a rounded and full front-end design; the body lines are smooth, making the overall appearance more balanced and practical. 2. Handling. The Sunny's engine features an EFI dual-mode dual-hole multi-point fuel injection system, which can provide precise and appropriate fuel injection according to different road conditions and engine load levels. Therefore, it offers more reliable mixture ratios and responsiveness compared to general electronic fuel injection systems.

8

5

Share

Where is the Auto Start-Stop System Switch?

The auto start-stop system switch is located on the left side of the steering wheel. The switch button for the auto start-stop system is a circle with an 'A' inside and the letters 'OFF' below it. Here is more information about the auto start-stop system: 1. The engine auto start-stop system automatically shuts off the engine when the vehicle comes to a temporary stop (e.g., at a red light) and restarts the engine when it's time to move again. Its English name is STOP&START, abbreviated as STT. 2. It works by integrating an enhanced motor with idle start-stop functionality into a traditional engine, allowing the engine to completely shut off when idle stop conditions are met. When the vehicle needs to move again, the idle start-stop motor system quickly responds to the driver's command, restarting the engine instantly and seamlessly, thereby significantly reducing fuel consumption and exhaust emissions.

7

1

Share

How to reset the tire pressure light on Audi A3?

Here are the steps to reset the tire pressure light on Audi A3: 1. Adjust the tire pressure to the specified value. 2. Press the "CAR" button on the dashboard to enter vehicle settings. 3. Rotate the knob to select tire pressure reset. 4. Click to confirm and complete the reset. Below is related information about tire pressure: 1. Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure tire pressure. The system transmits pressure information from inside the tire to a central receiver module via wireless transmitters, then displays the tire pressure data. 2. The system will automatically alert when tire pressure is too low or there is a leak.

2

3

Share

How to Lift the Wiper Blade Up?

Is the Mercedes-Benz V-Class a domestically produced car?

How to Install a Beam Wiper Blade?

Are Transmission Fluid and Power Steering Fluid the Same?

Where is the Nissan Sunny OBD interface located?

Where is the Auto Start-Stop System Switch?

How to reset the tire pressure light on Audi A3?

What does it mean when the car battery warning light comes on?

Why is the engine light on in the Magotan?

How to Self-Rescue When a Car Falls into Water

How to Turn on Car Air Conditioning in Winter?