How to lift the rear seats of the Buick Verano?

1 Answers
StHaley
07/30/25 7:45am
To raise the seat back of the rear seats in the Buick Verano, follow these steps: 1. Push the seat back backward until it locks into the upright position. 2. Ensure that the rear seat belts are not twisted or caught between the seat cushion and the seat back. 3. When the seat back is locked in place, the red tab next to the seat back lever will retract. 4. If you want to remove the rear seats, the method is as follows: There are clips on both sides at the front of the rear seat cushion. Lift up forcefully while rocking back and forth. Once both clips are released, pull the seat cushion backward firmly. There are three metal hooks at the back. If you are not confident in your DIY skills, it is recommended to have them removed at a 4S shop or a car wash.
Was this review help?
20
3
Share
More Forum Discussions

What is the ground clearance of the Toyota Camry?

The minimum ground clearance of the Toyota Camry is 130 millimeters. The minimum ground clearance of the Toyota Camry refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. The higher the ground clearance of the Toyota Camry, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds will decrease. The Toyota Camry is a mid-size sedan under GAC Toyota, meeting the China VI emission standards. The dimensions of the Toyota Camry Sport Edition are 4900 mm in length, 1840 mm in width, and 1455 mm in height, with a wheelbase of 2825 mm. The dimensions of other versions are 4855 mm in length, 1840 mm in width, and 1455 mm in height, with the same wheelbase of 2825 mm. Generally, the ground clearance of sedans ranges between 110 mm and 150 mm, while SUVs have a ground clearance between 200 mm and 250 mm. However, the ground clearance of the Toyota Camry is not static and depends on the load condition. Therefore, changes in ground clearance should be considered based on the vehicle's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice depends on the vehicle's intended use and road conditions. For urban driving with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. For frequent travel to remote areas or driving on rough terrain, a vehicle with higher ground clearance is advisable to avoid underbody scratches or damage. The minimum ground clearance of the Toyota Camry is 130 millimeters. The minimum ground clearance of the Toyota Camry refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. The higher the ground clearance of the Toyota Camry, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds will decrease.
3
0
Share

Is it mandatory to have Toyota's first inspection within 3 months?

Toyota's first inspection must be completed within 3 months. Below are the relevant details: 1. First inspection: It involves checking specified parts of the equipment according to certain standards and cycles to detect potential equipment failures early. 2. Routine maintenance items: Replacement of engine oil and oil filter, air filter, fuel filter, and pollen filter; maintenance and replacement of spark plugs; inspection and maintenance of systems related to transmission oil, etc. The main focus is on changing the engine oil and oil filter to maintain the lubrication system, whose primary function is to effectively lubricate various components of the car engine and prevent excessive wear.
4
5
Share

How to Check Engine Oil Level?

To check the engine oil level, follow these steps: 1. Perform the check when the engine is cold. Locate the oil dipstick handle in the engine compartment; 2. Pull out the dipstick and use a paper towel to completely wipe off the oil from the dipstick head; 3. There are usually MIN and MAX markings on the dipstick. Reinsert the cleaned dipstick all the way in, then pull it out again; 4. Observe the oil adhering to the dipstick and check the level against the markings. To change the engine oil: 1. Use a jack to lift the vehicle, locate the drain plug and loosen it to drain the oil; 2. After removing the oil filter, place a container beneath it; 3. Install a new oil filter and add fresh oil.
6
2
Share

Is the Volkswagen Tayron equipped with a dry or wet transmission?

The Volkswagen Tayron is equipped with a wet transmission. The wet dual-clutch transmission utilizes transmission fluid to assist in cooling the clutch plates, as the clutch plates are immersed in the transmission fluid, which continuously circulates to dissipate heat. Taking the Volkswagen Tayron 2020 280TSI Two-Wheel Drive Comfort Smart Edition as an example, its body dimensions are: length 4589 mm, width 1860 mm, height 1660 mm, with a wheelbase of 2731 mm. The Volkswagen Tayron 2020 280TSI Two-Wheel Drive Comfort Smart Edition is powered by a 1.4T inline 4-cylinder turbocharged engine, with a maximum torque of 250 N·m, a maximum torque speed range of 1750 to 3000 rpm, and a maximum power speed range of 5000 to 6000 rpm.
5
5
Share

Do I need to turn on the turn signal for uphill fixed-point parking?

Uphill fixed-point parking does not require turning on the turn signal, as driving uphill is always in a straight line without any turns. Turn signals are only needed when making turns, so there's no need to use them in this scenario. Below are the specific details: 1. Fixed-point parking and hill start: Fixed-point parking on an uphill road and starting on a slope are assessment points in the driver's test. This includes two test items: first, fixed-point parking on an uphill road, followed by starting and moving on the slope, which is one of the mandatory test items. 2. Requirements for fixed-point parking: For fixed-point parking, the vehicle's front bumper must be positioned in the middle of the yellow line designated for fixed-point parking. The bumper must not exceed or be behind the yellow line by more than 50 centimeters. The front and rear right wheels must stop between the edge yellow line and the white line (width of 30 centimeters).
15
2
Share

What is the reason for the frequent central brake light error in the Audi A4L?

Audi A4L central brake light warning indicates insufficient brake fluid, requiring the owner to promptly replenish the brake fluid. Below are the relevant details: 1. Audi: A German luxury car brand, its logo consists of four interlocking rings. Currently a subsidiary of Volkswagen Group. On December 20, 2018, Audi ranked 51st in the World's 500 Most Influential Brands list. In October 2019, it ranked 42nd in Interbrand's Global Top 100 Brands. 2. Brake Fluid: There are three types of brake fluid. When purchasing, choose a reliable manufacturer, and the higher the grade, the better. Its braking working pressure is generally 2MPa, and can reach up to 4~5MPa. All liquids have the characteristic of being incompressible. In a sealed container or a pipeline filled with liquid, when the liquid is under pressure, it quickly and evenly transmits the pressure to all parts of the liquid.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.