How to Know Your Car's Location?

What Causes Vehicle Body Shaking at Speeds of 70-80 km/h?

The causes of vehicle body shaking at speeds of 70-80 km/h are as follows: 1. Ignition system issues: Check the working condition of spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or inadequate spark plug firing can lead to such symptoms. 2. Unstable oil pressure: Even after cleaning engine carbon deposits, throttle valve, replacing oil pads and spark plugs, if the body still shakes at idle, it is recommended to visit a 4S shop to check the fuel supply pressure and intake pressure sensor. Abnormal fuel pump supply pressure or incorrect values and poor performance of the intake pressure sensor can cause body shaking. 3. Aging engine mounts: Engine mounts act as the shock absorption system for the engine, absorbing minor vibrations during operation. If the engine mounts are faulty, these vibrations can be transmitted to the steering wheel and cabin, causing shaking at idle. 4. Severe engine carbon deposits: The most common cause of vehicle shaking is excessive dirt on the throttle valve or too much carbon buildup in the fuel injectors.

15

4

Share

What is the difference between coasting with the clutch pressed and coasting in neutral?

The differences between coasting with the clutch pressed and coasting in neutral are as follows: 1. When coasting in neutral: The engine power is completely disconnected from the transmission. When coasting with the clutch pressed, the power is disconnected—pressing the clutch disengages it, releasing the clutch engages it, and partially releasing it results in a semi-engaged state. 2. From a safety perspective: Coasting in gear is better because the engine provides some level of resistance. Braking while coasting in gear offers much better braking performance compared to pressing the clutch and then braking. For short durations and under safe conditions, using the clutch for control is acceptable, but prolonged clutch pressing can damage the release bearing. Additionally, shifting back into gear after being in neutral might fail, preventing the use of engine braking. On downhill slopes, prolonged use of the brakes alone can cause them to overheat and fail, whereas engine braking helps assist in vehicle deceleration.

14

4

Share

What is the Toyota Gold Emblem Car?

Toyota gold emblem generally refers to the commemorative edition launched by Toyota. Below is an extended introduction: 1. Introduction to the gold commemorative edition car: The so-called commemorative edition is based on the regular version but with additional configurations. To distinguish it from the regular version, the emblem is changed to gold. 2. Introduction to different emblems: Almost every car sold by Toyota in Japan has a different emblem. Gold and silver emblems represent different levels of car configurations. The top-tier Toyota Crown uses a gold emblem to symbolize nobility, with overall design, performance, and configurations surpassing those of the silver emblem Toyota. Therefore, the Toyota Crown with a gold emblem is more expensive than the one with a silver emblem.

18

2

Share

Where is the largest used car trading market in Suzhou?

The largest one is located at the intersection of Mayun Road and Tayuan Road in Suzhou New District. Relevant details are as follows: 1. Functions: The used car market is a place for secondary trading of motor vehicle commodities, serving both as an intermediary and an operator. Specifically, the functions of the used car trading market include: insurance, consignment, purchase, used car appraisal, licensing, transfer of ownership, change of registration, replacement, auction, sales, and other services. 2. Inspection: In addition, the used car trading market must strictly comply with national requirements to verify the legality of used car transactions, and must prevent illegal modified vehicles, smuggled vehicles, stolen vehicles, and vehicles with incomplete payment vouchers and documentation from entering the market.

16

2

Share

What is the placement direction of the scooter pulley beads?

Facing the pulley disc, the side with rubber should all be placed towards the right. Related details are as follows: 1. Function: One of the rotating components of a scooter, the pulley beads (also known as moving beads, capable of radial movement) are influenced by the engine's speed. As the speed gradually increases, the pulley beads are subjected to outward centrifugal force, overcoming the force of the large spring, and move radially along the sliding groove towards the outer edge of the disc. This increases the force squeezing the axially moving disc, enlarges the working radius, and reduces the diameter of the driven disc, thereby changing the transmission ratio. 2. Heavy pulley beads: Due to greater centrifugal force, even with slight speed, the beads can quickly reach the outer edge of the disc, effectively increasing the diameter of the driving disc and reducing the transmission ratio. This causes the driven disc's shoe blocks to quickly spread out and contact the clutch bell, thus driving the motorcycle. In other words, it allows for starting at low speeds and can even increase the top speed because heavy beads can be easily flung to the outermost edge of the pulley disc.

11

1

Share

What causes the Ford Focus reverse gear to malfunction?

The reasons for the Ford Focus reverse gear malfunction are as follows: 1. It may be due to electronic linkage between the brake system and the automatic transmission: When shifting gears, the clutch pedal is not fully depressed, causing gear damage. Additionally, when not using the clutch, the foot should not rest on the clutch pedal to avoid excessive wear of the release bearing. Solution: Have it inspected and repaired at a 4S shop. 2. It may be caused by idling gear engagement: In automatic transmission models, the engine speed is very high during the first few seconds after startup. If the gear is shifted from neutral to reverse before the engine speed stabilizes, it will cause strong impact vibrations to the transmission, damaging the gearshift switch inside the transmission. The scientific approach is to wait until the RPM displayed on the instrument panel stabilizes before using the reverse gear. Solution: Pay attention to the coordinated operation of the clutch pedal, throttle, and gear lever when shifting gears. The gear lever must be pushed firmly into place to ensure complete gear engagement, preventing gear damage or automatic disengagement of the transmission while driving.

6

3

Share

How to Know Your Car's Location?

What Causes Vehicle Body Shaking at Speeds of 70-80 km/h?

What is the difference between coasting with the clutch pressed and coasting in neutral?

What is the Toyota Gold Emblem Car?

Where is the largest used car trading market in Suzhou?

What is the placement direction of the scooter pulley beads?

What causes the Ford Focus reverse gear to malfunction?

What is the fuel consumption of the Jeep Renegade?

Are Ford 6AT and GM 6AT the Same?

What is manenati?

Manual Transmission: Engage Gear First or Release Handbrake First?