How to Install Tire Pressure Monitoring System on Kia K3?

1 Answers
ElleRose
07/29/25 2:11pm
Installation method for tire pressure monitoring system on Kia K3: Remove the original valve and replace it with a valve equipped with tire pressure sensor. There are two types of tire pressure monitoring systems: direct tire pressure monitoring system and indirect tire pressure monitoring system. The Kia K3 is a compact car with body dimensions of 4600mm in length, 1780mm in width, and 1445mm in height, with a wheelbase of 2700mm. The Kia K3 is equipped with two engines: a 1.5-liter naturally aspirated engine and a 1.4-liter turbocharged engine. The 1.5-liter naturally aspirated engine has a maximum power of 85 kW and a maximum torque of 143.9 Nm; the 1.4-liter turbocharged engine has a maximum power of 96 kW and a maximum torque of 211 Nm.
Was this review help?
8
0
Share
More Forum Discussions

What is the method for replacing brake fluid in an electric vehicle?

Replacing the brake fluid in an electric vehicle involves the following steps: 1. Open the car's hood and locate the brake fluid reservoir; 2. Remove the reservoir cap and inspect the quality of the brake fluid; 3. Use a syringe to extract all the old brake fluid from the reservoir and then add new brake fluid. Brake fluid has hygroscopic properties, and if not replaced for a long time, it can corrode the braking system, potentially creating safety hazards while driving. Since absorbed moisture lowers the boiling point of brake fluid, it can lead to insufficient braking pressure and affect the vehicle's braking performance. It is recommended that owners replace the brake fluid every two years or every 40,000 kilometers.
11
2
Share

Should You Press the Clutch When Shifting Gears?

When shifting gears, you need to press the clutch. When changing gears in a car, you should press the clutch pedal all the way down, shift into second gear, release the clutch to the semi-engaged state, then gently press the accelerator, release the clutch completely, and finally increase the throttle. The same procedure applies when upshifting to higher gears. The requirements for a car's clutch include quick disengagement, smooth engagement, and sufficient heat dissipation capability. The clutch is a mechanical device located between the engine and the transmission, where the output shaft of the clutch serves as the input shaft of the transmission. While driving, the driver controls the clutch pedal to separate or connect the engine and clutch, thereby cutting off or transmitting the engine's power to the transmission.
6
0
Share

What are the early symptoms of a bad starter?

Early symptoms of a bad starter: When turning the key to start, there is little resistance felt, and only a clicking sound is heard without the engine starting. Reasons why the starter fails to start: 1. Insufficient battery power or loose terminal connections; 2. Short circuit in the starter solenoid switch coil or poor contact with the contact disc; 3. Burned or eroded relay contacts, or short circuit/burned-out relay magnetic coil; 4. Physical deformation of the starter's armature shaft, worn brushes, poor spring contact, or dirty commutator. The starter, also known as the motor, converts the battery's electrical energy into mechanical energy to drive the engine flywheel and initiate engine startup.
19
0
Share

What Type of Oil Should Be Used for the Trumpchi GS7?

Trumpchi GS7 recommended oil: For newer vehicles with lower mileage, it is advisable to use 30-viscosity oil; for older vehicles with higher mileage, 40-viscosity oil is recommended. Engine oil is the lubricant used in engines, composed of base oil and additives, which serves to lubricate and reduce friction, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. The Trumpchi GS7 is a new five-seat midsize SUV under the GAC Trumpchi brand, with dimensions of 4730mm in length, 1910mm in width, and 1770mm in height, and a wheelbase of 2720mm. The Trumpchi GS7 is equipped with two engine options: a 2.0-liter inline 4-cylinder turbocharged engine and a 1.8-liter inline 4-cylinder turbocharged engine.
4
5
Share

How to Remove the Interior Rearview Mirror of the Sylphy?

The method for removing the interior rearview mirror of the Sylphy: The interior rearview mirror is fixed with a clip-on mechanism. Use a plastic pry tool to gently lift the clip outward and pull it backward along the windshield to remove it. Avoid using sharp or hard objects to pry, as this may damage the glass and the front window film. Rearview mirrors are categorized by installation position into exterior rearview mirrors, lower rearview mirrors, and interior rearview mirrors. The Sylphy is a new strategic model launched globally by Nissan, featuring innovative design and advanced technology, with a stylish and elegant exterior shaped by S-curve dynamics. The dimensions of the Nissan Sylphy are 4641mm in length, 1815mm in width, and 1450mm in height, with a wheelbase of 2712mm.
6
1
Share

What are the body length, width, and height of the Fista?

The body length, width, and height of the Fista are 4660mm, 1790mm, and 1425mm respectively, with a wheelbase of 2700mm. The front grille of the Fista features a honeycomb design with a large area, topped by a thick chrome trim connecting the matrix-style headlights on both sides, giving it a strong aggressive look. The hood has four symmetrical raised lines, enhancing the overall sense of layering and aggressiveness. The Fista offers two engine options: a 1.4T and a 1.6T. The 1.4T engine delivers a maximum power of 103 kW and a maximum torque of 242 Nm, while the 1.6T engine produces a maximum power of 140 kW and a maximum torque of 265 Nm.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.