How to install the generator belt on the Bestune X40?

1 Answers
ElleMarie
07/25/25 7:25am
The method for installing the generator belt on the Bestune X40: 1. Pull the generator's main pulley shaft outward to facilitate belt winding; 2. Also pull the two idler pulleys of the generator outward; 3. Correctly align the position of the generator's main pulley shaft, ensuring the protruding part of the shaft faces outward, then loop the belt onto the generator's main pulley shaft; 4. Loop the belt onto the two idler pulleys of the generator, and finally reinstall the generator casing. The Bestune X40 has body dimensions of 4310mm in length, 1780mm in width, and 1680mm in height, with a wheelbase of 2600mm. Its exterior features a distinctive hexagonal front grille that inherits Bestune's genetic design, complemented by sleek, elongated front headlights for a strong personality. This model adopts a reinforced 3H structure body and is equipped with the BOSCH ninth-generation ESP system. The 4GB series high-performance engine is paired with a third-generation six-speed automatic transmission, while the 1.6L optimal displacement balances high power performance with fuel efficiency.
Was this review help?
11
2
Share
More Forum Discussions

Is a Car Considered a Stock Car After Three Months?

A car that has been in stock for three months is not considered a stock car. Generally, a stock car refers to a vehicle that has remained unsold for more than three months after being manufactured and leaving the factory. In essence, most stock cars are stored in open-air parking lots, exposed to sun and rain, without basic maintenance. This can lead to issues such as moisture damage and aging of various fluids, electronic components, batteries, rubber seals, and tires. If the stock time exceeds one year, you can request the dealership to replace the original engine oil. Additionally, check the production date of the tires—new tires older than two years may face rubber aging risks, so it’s advisable to ask the dealership to replace them as well. If these two aspects are addressed, such a stock car should not affect its usability. If the stock time approaches five years, it’s not recommended to purchase such a vehicle unless the discount is substantial. A five-year stock period means the engine oil, tires, rubber bushings in the suspension, and dust covers on the universal joints may all need replacement due to aging.
6
2
Share

What is SAE 10W-30 engine oil?

Engine oil SAE 10W-30 is referred to as a "multi-grade" oil. The smaller the number in SAE 10W (such as 10 in this example), the less likely the oil is to become viscous at low temperatures. Here is an introduction to engine oil: Introduction to engine oil: Engine oil, also known as engine lubricating oil, is called Engine-oil in English. It has a density of approximately 0.91×10 (kg/m³) and serves functions such as lubrication and wear reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion protection, and shock absorption. It is hailed as the "blood" of a car. Composition of engine oil: Engine oil consists of two parts: base oil and additives. The base oil is the main component of lubricating oil, determining its basic properties. Additives can compensate for and improve the shortcomings of the base oil's performance, imparting certain new properties, making them an important part of lubricating oil.
13
0
Share

What is the method for removing the seats in a Buick GL8?

The method for removing the seats in a Buick GL8 is as follows: 1. Pull the handle located near the window on the rear seats; 2. Fold the backrest of the rear seats forward and push the seat cushion towards the rear of the vehicle; 3. Lift the seat upwards to remove it. Taking the 2021 Buick GL8 as an example, its body dimensions are: length 5238mm, width 1878mm, height 1776mm, wheelbase 3088mm, fuel tank capacity 66l, and luggage compartment volume 475l. The 2021 Buick GL8 is equipped with a 2.0t turbocharged engine, with a maximum horsepower of 237ps, maximum torque of 350nm, maximum power of 174kw, and is paired with a 9-speed automatic transmission.
10
5
Share

What is the minimum speed a car should not go below in third gear?

When driving in third gear, the speed of the car should not be lower than 20 km/h. The corresponding speed range for third gear is 20-40 km/h. Speed ranges for different gears: First gear corresponds to a speed range of 0-5 km/h. Second gear corresponds to 5-20 km/h, third gear to 20-40 km/h, fourth gear to 40-60 km/h, and fifth gear to 60-100 km/h. The relationship between car gears and speed: When downshifting, follow the principle of deceleration before downshifting. You can skip gears if necessary. When the speed matches the gear, the car's performance is at its best, and fuel efficiency is highest. If the speed does not match the gear, such as high speed with low gear or low speed with high gear, it not only increases fuel consumption but also causes irreversible damage to the engine and transmission. Therefore, it is essential to maintain the correct gear-speed match while driving.
5
2
Share

How to Open the Fuel Tank Cap on a Mondeo?

The method to open the fuel tank cap on a Mondeo: The fuel tank uses an external opening mechanism. When the central locking is unlocked, simply press the outer fuel tank cover to open it. The Mondeo's fuel tank features a design without an inner cap, allowing direct insertion of the fuel nozzle during refueling. The fuel tank has a capacity of 62L and can only be filled with 92-octane or higher unleaded gasoline. The Mondeo is a mid-size sedan sold by Ford Motor Company in multiple markets worldwide. In terms of body dimensions, it measures 4873mm in length, 1852mm in width, and 1470mm in height, with a wheelbase of 2850mm. The Mondeo comes standard with 8 airbags across all models, including front airbags, curtain airbags, knee airbags, and rear side curtain airbags on both sides.
2
5
Share

What is the reason for the clicking sound when pulling the handbrake?

The reason for the clicking sound when pulling the handbrake is: The handbrake system is internally equipped with a ratchet and pawl mechanism. When the handbrake is pulled up, the pawl engages with the ratchet, causing the handbrake to automatically lock and produce a clicking sound. The function of the handbrake is to provide braking when parking on flat or inclined surfaces, preventing the vehicle from moving unintentionally when unattended and avoiding traffic accidents. Precautions for using the handbrake: 1. Always engage the handbrake when parking and turning off the engine; 2. Use the handbrake in conjunction with the neutral gear; 3. Avoid pulling the handbrake too tightly; 4. Release the handbrake completely when starting the car; 5. If the braking system fails while driving on the highway, you can intermittently, slowly, and repeatedly pull and release the handbrake to bring the vehicle to a stop.
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.