How to Install Mercedes-Benz Welcome Lights?

What is the fuel tank capacity of the Peugeot 5008 in liters?

2021 Peugeot 5008 has a total of 7 models, all with a fuel tank capacity of 56 liters. The 2021 Peugeot 5008 is equipped with 1.6-liter and 1.8-liter turbocharged engines, and the transmission type is an automatic transmission (AT). All models feature a front-wheel-drive configuration. Among vehicles in the same class, the 2021 Kodiaq TSI330 5-seater two-wheel-drive standard version has a fuel tank capacity of 60 liters, while the 2020 Santa Fe 380TGDi automatic two-wheel-drive GL Elite version has a fuel tank capacity of 71 liters. During the actual refueling process, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the car manufacturer is measured from the bottom of the tank to the safe limit level. There is still some space from the safe limit level to the tank opening, which is reserved to allow for fuel expansion when the temperature rises, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel may exceed the marked tank capacity. To check the remaining fuel level, drivers can observe the fuel gauge on the right side of the dashboard, which is marked with E and F. When the pointer is close to E, it indicates low fuel, while nearing F means the fuel level is sufficient.

12

5

Share

Where is the Citroen OBD port located?

Citroen's OBD interface is located in the small compartment in front of the gear lever or under the small cover below the steering wheel near the left knee. Open it to see the plug. OBD stands for On-Board Diagnostics, which monitors the working conditions of the engine's electronic control system and other functional modules of the vehicle in real time. Here is some relevant information: 1. This system can monitor the working conditions of the engine's electronic control system and other functional modules of the vehicle in real time during operation. If any abnormal conditions are found, it will determine the specific fault according to a specific algorithm and store it in the system's memory in the form of diagnostic trouble codes. The useful information obtained after system self-diagnosis can help with vehicle maintenance and repair, and maintenance personnel can read it using the vehicle's original factory-specific instrument. 2. When a system fault occurs, the malfunction indicator lamp or check engine warning light will illuminate, and the OBD system will store the fault information in the memory. Relevant information can be read in the form of fault codes through standard diagnostic instruments and diagnostic interfaces. Based on the fault code prompts, maintenance personnel can quickly and accurately determine the nature and location of the fault. 3. OBD connects various emission-related component information to the Electronic Control Unit (ECU), which has the function of detecting and analyzing emission-related faults. When an emission fault occurs, the ECU records the fault information and related codes and issues a warning through the malfunction indicator lamp to inform the driver.

12

0

Share

How to Solve the Problem of Valve Erosion and Air Leakage?

If it is caused by excessive carbon deposits, the carbon deposits can be removed. If the valve and valve seat are worn or eroded, the severity of the wear and erosion should be assessed. For minor wear and erosion marks, the sealing can be restored by grinding the valve and valve seat together. If the wear or erosion is severe or the contact ring has significantly widened, and grinding can no longer eliminate the issue, the valve seat ring can be milled, the valve can be polished, and then they can be ground together to restore sealing performance. 1. Incorrect fit clearance between the valve and valve guide. If the clearance is too large, the valve will wobble and tilt when closing, leading to poor sealing. If the clearance is too small, the valve may get stuck in the guide, preventing it from closing properly or at all. In such cases, the cause of the excessive or insufficient clearance should be identified, and the guide or valve affecting the normal fit clearance should be replaced. Insufficient or broken valve spring tension can also prevent the valve from closing or sealing properly. Solution: Replace the valve spring. 2. If the valve clearance is too small, components like the valve stem may not have enough room to expand when heated, resulting in improper sealing. Adjust the valve clearance as required. Valve leakage noise typically occurs outside the valve chamber and is more noticeable under high load and low speed conditions. The noise increases with the load. The main reasons for this noise are improper operation during valve seat reaming or excessive wear of the valve guide bore, causing the valve seat to tilt or the valve clearance to be too small, leading to valve erosion and improper sealing, which results in air leakage noise.

18

0

Share

What documents are needed for license plate registration?

Documents required for vehicle license plate registration: vehicle certification of conformity, triplicate vehicle invoice, original and duplicate copies, original ID card and photocopy, original temporary residence permit and photocopy. The vehicle management office shall, within two days from the date of accepting the application, confirm the motor vehicle, verify the vehicle identification number imprint, review the submitted certificates and documents, and issue the motor vehicle registration certificate, license plate, driving license, and inspection qualification mark. Below is more related information: The following circumstances will result in refusal of registration: 1. The certificates and documents submitted by the motor vehicle owner are invalid. 2. The motor vehicle's origin certificate has been altered or the motor vehicle owner recorded in the origin certificate does not match the identity certificate. 3. The certificates and documents submitted by the motor vehicle owner do not match the motor vehicle. 4. The motor vehicle was produced without permission from the State Council's motor vehicle product authority or imported without permission from the national motor vehicle import authority. 5. The motor vehicle's technical data does not match the data announced by the State Council's motor vehicle product authority. 6. The motor vehicle's model, engine number, vehicle identification number, or related technical data does not comply with national safety technical standards. 7. The motor vehicle has reached the mandatory scrapping standard set by the state. 8. The motor vehicle has been legally seized or impounded by the People's Court, People's Procuratorate, or administrative law enforcement departments. 9. The motor vehicle is stolen. 10. Other circumstances that do not comply with laws and administrative regulations.

14

2

Share

What is the domestic grade corresponding to c36000?

C36000 corresponds to the domestic model HPb62-3. Below are the specific details about C36000: 1. Chemical Composition: C36000 is a leaded brass defined by the American ASTM standard. Automotive zinc (Zn) balance, lead (Pb) 2.5～3.7, iron (Fe) ≤0.35, copper (Cu) 60～63, total impurities % ≤0.5, execution standard B16M. 2. Mechanical Properties: Tensile Strength (N/mm2) ≥510≥490≥451≥412.

7

5

Share

How many kilometers can a full tank of fuel last for the Leiling?

The distance a full tank of fuel can last for the Leiling varies depending on the model: 1. The 1.2t model can travel 900 kilometers; 2. The 1.8l model can travel 1040 kilometers. Below are the relevant details: 1. The Leiling 1.2t version has a fuel tank capacity of 50 liters, with a combined fuel consumption of 5.5l/100km as per the Ministry of Industry and Information Technology, theoretically allowing a full tank to last 900 kilometers; the Leiling 1.8l hybrid version has a fuel tank capacity of 43 liters, with a combined fuel consumption of 4.1l/100km, theoretically allowing a full tank to last 1040 kilometers. 2. The actual distance a full tank of fuel can last for the Leiling is closely related to the driver's habits, fuel quality, and road conditions, so the above data is for reference only. 3. The Leiling Hybrid is a compact hybrid car produced by GAC Toyota, with body dimensions of 4640*1780*1455mm. 4. In terms of power, the Leiling Hybrid uses a hybrid system combining a 1.8-liter naturally aspirated engine and an electric motor. The engine has a maximum horsepower of 98, a maximum power of 72kw, and a maximum torque of 142N·m. The electric motor has a maximum horsepower of 72, a total power of 53kw, and a total torque of 163N·m.

19

3

Share

How to Install Mercedes-Benz Welcome Lights?

What is the fuel tank capacity of the Peugeot 5008 in liters?

Where is the Citroen OBD port located?

How to Solve the Problem of Valve Erosion and Air Leakage?

What documents are needed for license plate registration?

What is the domestic grade corresponding to c36000?

How many kilometers can a full tank of fuel last for the Leiling?

Why is the car steering wheel heavier on one side and lighter on the other?

What is the tire model specification of the Zhijun?

Can the car still be driven if it shows a tire leak?

What are the models of Honda convertible cars?