How to Identify Whether Motor Oil is Semi-Synthetic or Fully Synthetic?

1 Answers
SanEthan
07/29/25 10:34pm
There are two methods to determine whether motor oil is semi-synthetic or fully synthetic: 1. Packaging: Check the outer packaging of the oil, which usually indicates the type of oil. 2. Oil color: The color of the oil can also be used to distinguish between types. Mineral oil tends to have a darker color, while synthetic oil is lighter, appearing as a transparent light yellow. If labeled 'Full-Synthetic,' it is fully synthetic oil. The differences between semi-synthetic and fully synthetic oils are as follows: 1. Semi-synthetic oil is based on mineral oil refined through hydrogenation. Synthetic motor oil is derived from ethylene and propylene dispersed from natural gas or crude oil, undergoing polymerization, catalysis, and other complex chemical reactions to produce high-molecular lubricants. 2. Fully synthetic oil has a broader temperature range and longer service life. 3. For the same oil film requirements, synthetic oil has lower viscosity, while semi-synthetic oil has higher viscosity compared to synthetic oil. 4. Semi-synthetic oil is mainly used for economical vehicles, whereas fully synthetic oil is primarily used for luxury vehicles. 5. The amount of additives differs, with fully synthetic oil containing more and semi-synthetic oil containing fewer additives. 6. Fully synthetic oil has better anti-aging stability. 7. Fully synthetic oil provides better engine protection. 8. The price of fully synthetic oil is higher than that of semi-synthetic oil.
Was this review help?
3
4
Share
More Forum Discussions

What is the normal water level for a car?

There are maximum and minimum warning lines on the car's radiator, and the water level between these two lines is considered normal. Below is relevant information about the car radiator's water level: 1. The car radiator, also known as a heat exchanger, is a key component of the car's cooling system. Its function is to dissipate heat. The coolant absorbs heat in the water jacket, flows to the radiator to release the heat, and then returns to the water jacket in a continuous cycle, achieving the effect of heat dissipation and temperature regulation. It is also an important part of the car engine; 2. The liquid added to the car radiator is not pure water but a coolant mixture of ethylene glycol and water.
14
0
Share

What is the wading depth of the Camry?

The maximum wading depth of the Camry is 500mm. The wading depth of the Camry is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the Camry is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingress. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, and other reference points like the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not enter the water recklessly; consider alternative routes instead.
14
5
Share

What is the function of the third button on the Nissan Qashqai key?

The third button on the Nissan Qashqai key is the vehicle locator button. Below is relevant information about the Qashqai: 1. Introduction: The Qashqai, the first creation from Nissan's European Design Center, derives its name from the nomadic tribes inhabiting Iran's desert regions, meaning "urban nomad." 2. Exterior: The Qashqai's front fascia embodies Nissan's traditional design elements. Though compact, it conveys a robust impression with its broad grille and prominent chrome logo on the cooling grille, instantly recognizable as part of its lineage. The two arched protrusions on the engine hood, paired with irregular pentagonal headlights, give the front end a playful, cartoon-like appearance.
10
2
Share

Can I Change Driving Schools After Registration?

Generally, after an applicant registers, the driving school cannot be changed. Below is relevant information about changing driving schools after registration: 1. After registration, the candidate's information is entered into the public security vehicle management network, meaning the candidate's details are already registered in the nationwide examination system under the original driving school. While instructors can be changed, the school itself cannot. This system is nationally interconnected; 2. If a change is absolutely necessary, one must apply through the public security department to cancel the previous registration, then re-file the documents before being able to register anew.
18
5
Share

Why does the car feel unstable after changing tires?

The main reasons for the car feeling unstable after changing tires are the use of tires with different specifications or tread patterns, or failing to perform wheel balancing after tire replacement. Below are detailed explanations of the causes of car instability after tire replacement: 1. Using tires with different specifications or inconsistent tread patterns; 2. Not performing wheel balancing after tire replacement, which causes the tire's unbalanced state to create a floating sensation during high-speed driving, hence wheel balancing is necessary after tire replacement. The primary purpose of wheel balancing is to prevent tires from bouncing up and down or swaying left and right during high-speed driving, and to avoid steering wheel vibration and body shaking issues in the vehicle.
6
3
Share

What to Do When the Remote Key Doesn't Roll Up the Window When Held Down?

Remote key window control failure occurs when the car's body computer loses the data for the remote key to control the windows. This function can be restored by performing an initialization match using the door window switch and the lock button. The specific steps are as follows: 1. Step on the pedal: Depress the car's brake pedal. 2. Press the start button: Press the car's one-touch start button. 3. Turn on the power: The car's dashboard lights up, and the entire vehicle's power is turned on. 4. Pull the window regulator: Pull the car's window regulator up to the highest point. 5. Press the lock button: Press the car's door lock button and hold it for 10 seconds.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.