How to Handle a One-Time Deduction of 12 Points on an A2 Driver's License?

2 Answers
Brianna
07/25/25 10:07am
If an A2 driver's license is deducted 12 points at one time, the handling procedures are as follows: 1. You need to go to the traffic management department of the public security authority at the place where the motor vehicle driver's license was issued or where the driver's illegal act occurred, to receive 7 days of training on road traffic safety laws and related knowledge, with 8 hours per day. 2. After completing the 7-day training, you must also retake the subject one test, with the same content as new driving test candidates. 3. After passing the subject one test, the points will be cleared, and the motor vehicle driver's license will be returned. Drivers who fail the test will need to retake the training and examination.
Was this review help?
6
3
Share
VonWalter
08/11/25 7:34pm
When I used to drive an A2 truck, I also got 12 points deducted at once for speeding, which I deeply regretted. The first thing I had to do was stop driving immediately to avoid being caught driving without a valid license. I went to the vehicle management office to apply for processing, and they required me to attend a seven-day traffic safety course. The course covered traffic rules and accident prevention, which was quite practical. After completing the course, I had to take the theoretical test (Subject One). The questions weren’t difficult, but I had to review carefully. After passing the test, I waited about one or two weeks, and my license was reinstated. The whole process took some time and cost a few hundred yuan. Since then, I’ve been extra cautious when driving. I check my points more frequently using apps, as the consequences of accidents involving large vehicles are too severe. Safety always comes first to ensure smooth long-distance trips.
Was this review help?
13
5
Share
Expand All
More Forum Discussions

How to Activate the Windshield Washer Spray?

The method to activate the windshield washer spray is: The washer switch is located on the wiper control lever on the right side of the steering wheel. Pull the control lever towards the driver to spray water. The function of the wiper is: To remove raindrops, debris, and dust attached to the vehicle's windshield, improving the driver's visibility and enhancing driving safety. The steps to replace the car wiper are: 1. Lift the wiper upright; 2. Press the clip below and remove the wiper blade; 3. Take off the wiper; 4. Lift the front end of the middle clip; 5. Insert the wiper into the middle clip, pull it tight by hand, and the replacement is complete once you hear a click sound.
13
4
Share

What brand of car is Flat?

Flat is the Fiat automobile brand, produced in Italy, and is the world's first manufacturer of microcars. Fiat's models include: Bravo, Fiat 500, Viaggio, Siena, Palio, etc. Taking the 2013 Fiat 500 as an example, it is a microcar with body dimensions of: length 3547mm, width 1627mm, height 1520mm, and a wheelbase of 2300mm. The 2013 Fiat 500 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.4L naturally aspirated engine, delivering a maximum horsepower of 101PS, a maximum power of 75kW, and a maximum torque of 133Nm, paired with a 6-speed automatic transmission.
4
4
Share

What procedures are required to change the engine number?

The procedures required to change the engine number are: 1. The vehicle owner needs to bring the original and photocopy of their ID card, vehicle driving license, motor vehicle registration certificate, proof document for engine replacement, and vehicle information change application form to the vehicle management office to have the staff issue a vehicle inspection application; 2. The owner takes the vehicle inspection application to the inspection site to have the vehicle inspected; 3. After passing the inspection, the owner needs to go to the service hall to process the change of the vehicle engine number. The methods to check the engine number are: 1. Use the owner's name, communication device, driving license, or license plate number to check on the traffic management bureau's website; 2. Check through documents such as the driving license, motor vehicle registration certificate, car purchase invoice, factory certificate, operating license for commercial vehicles, and vehicle insurance card; 3. The engine number of the car is located near the left spark plug of the car engine, and the engine number can be seen by opening the car's hood.
1
1
Share

Where is the fuel filter located in a Honda Accord?

The fuel filter in a Honda Accord is located inside the fuel tank. The fuel filter is a device that removes impurities from gasoline and generally needs to be replaced every 10,000 kilometers. Taking the 2021 Honda Accord as an example, it is a mid-size sedan with the following dimensions: length 4893mm, width 1862mm, height 1449mm, wheelbase 2830mm, fuel tank capacity 48.5 liters, and curb weight 1619kg. The 2021 Honda Accord features a MacPherson strut front suspension and a multi-link rear suspension. It is equipped with a 2.0L naturally aspirated engine producing a maximum horsepower of 146PS, maximum power of 107kW, and maximum torque of 175Nm, paired with an electronic continuously variable transmission.
1
0
Share

What is an Aston Martin?

Aston Martin is a British luxury car brand. The dimensions of this car are 4739mm in length, 1950mm in width, and 1279mm in height, with a wheelbase of 2805mm. It is equipped with a naturally aspirated 7.3-liter V12 engine, delivering a maximum power of 700 kW and a maximum torque of 553 Nm, with a top speed of up to 355 km/h, paired with a 6-speed automatic transmission. Exterior-wise, Aston Martin models feature carbon fiber front splitters, rear bumpers, and exhaust tailpipes. The interior includes sporty seats and steering wheel, alloy fabric upholstery, and 19-inch alloy wheels fitted with Bridgestone tires.
19
0
Share

How to Reset the Tire Pressure Light on Baojun 510?

Baojun 510 tire pressure light reset method: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button. After hearing a "ding" sound, release the button. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, completing the tire pressure reset. Solutions for insufficient tire pressure: If no damage is visible, simply inflate the tire to the normal pressure and reset the tire pressure system; If a puncture is found upon inspection, drive to a tire shop promptly for repair, then reinflate the tire; If the tire pressure warning reappears some time after inflation without any punctures, it may be due to air leakage caused by a deformed wheel hub. It is recommended to inspect the wheel hub and replace it if necessary. Hazards of low tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; Causes the steering wheel to feel heavy and may lead to veering, among other factors detrimental to driving safety.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.