How to fold the side mirrors on the Nissan Qashqai?

1 Answers
RileyLynn
09/08/25 4:48am
Press the automatic mirror folding button or rotate the knob to the automatic folding position, and both side mirrors will fold simultaneously. In this state, the automatically folded mirrors will automatically unfold when you start the vehicle next time.
Was this review help?
8
2
Share
More Forum Discussions

What is the function of the engine start-stop system?

The function of the engine start-stop system is to automatically shut off the engine when the vehicle comes to a temporary stop during driving. Here is a detailed introduction to the auto start-stop feature: 1. Auto Start-Stop Button: The auto start-stop button is located to the left of the cigarette lighter, marked with an icon of a circle containing the letter 'A' and the letters 'OFF' below. Simply press the button to deactivate the auto start-stop. 2. Default Activation: The auto start-stop is enabled by default. Each time the vehicle is restarted, the auto start-stop will be activated. This button cannot permanently disable the system; you need to press it every time you start the vehicle to turn off the auto start-stop.
17
1
Share

What does the A/C in a car air conditioner mean?

In a car, A/C stands for the air conditioning cooling device, also known as the air conditioning cooling switch. Here are the specific details about A/C: 1. Introduction: A/C is short for Air-conditioning in English, representing the air conditioning system. Pressing the A/C button activates the air conditioning to adjust the temperature according to the set value. At this time, the air conditioning compressor starts, increasing the engine load and fuel consumption. 2. Precautions: The A/C switch should only be used when turning on the air conditioning in summer. It is not used when turning on the air conditioning in winter. If the A/C button is pressed in winter, the warm air from the air conditioning will not only fail to function but also unnecessarily increase the engine load.
6
2
Share

What causes brake shudder at high speeds?

High-speed brake shudder can be caused by the following reasons: 1. Vehicle drivetrain malfunction: If the steering wheel shakes during high-speed driving, check whether the front wheel alignment angles meet specifications and adjust if necessary; 2. Overly loose or tight power steering belt: Severe steering wheel vibration when turning indicates issues with the power steering belt tension, primarily affecting mechanically hydraulic-assisted vehicles. Adjust or replace the belt as needed; 3. Incorrect tire dynamic balance values: Steering wheel vibration at certain speed ranges occurs due to improper tire balancing, which can cause shaking within specific speed ranges. Wheel hub deformation, incorrect tire pressure, uneven tire wear, or improperly installed balancing weights may all contribute to poor wheel dynamic balance.
16
5
Share

How to Use the One-Third Hood Alignment Method?

Align the right one-third of the hood with the roadside line to maintain a 30 cm distance between the right side of the vehicle and the roadside line. Here are the detailed steps: 1. Gear Shift: Turn on the left turn signal, shift into first gear to start, then drive close to the right side of the road, being careful not to steer too sharply. 2. Clutch Control: When the right one-third of the hood aligns with the roadside line, steady the steering wheel and make minor adjustments to maintain this alignment. After driving a short distance, the vehicle will straighten. As you approach the stopping point, observe the left rearview mirror's lower edge aligning with the solid stopping line of the pole, then press the brake and clutch to stop, and engage the handbrake. 3. Light Throttle: Upon receiving the instruction to start, complete the start within 30 seconds. Gradually release the clutch until you feel noticeable vibration in the vehicle, then steady the clutch, quickly release the handbrake, and slowly release the brake to allow the vehicle to start smoothly. If the vehicle moves too slowly or struggles to climb, lightly press the throttle.
8
1
Share

Where can I see that the engine oil is low-ash?

Use C-series certified low-ash engine oil. Here are specific details about low-ash engine oil: 1. Introduction to low-ash: Low-ash is generated by the combustion of certain additives in engine oil. Some of these ash deposits accumulate inside the engine, forming what car enthusiasts commonly refer to as "carbon deposits." Therefore, you can simply consider low-ash engine oil as producing fewer carbon deposits. 2. Key points: It's important to note that the current engine oil market is quite mixed. Many sellers, in order to boost sales, will privately label their oil bottles with API SP-grade standards without actually obtaining the relevant certification. Therefore, when selecting low-ash engine oil, always purchase well-known brands and choose products that have official certification and can be verified on the official API website. This will effectively help you avoid counterfeit or substandard engine oil products.
6
2
Share

Can Halogen Bulbs Be Replaced with LED Bulbs?

Halogen bulbs can be replaced with LED bulbs. The following are the benefits of replacing halogen bulbs with LED bulbs: 1. No radiation: LEDs use cold light sources, with minimal glare and no radiation, and do not produce harmful substances during use; 2. Energy-saving: LEDs operate at low voltage, use DC drive mode, and have ultra-low power consumption (0.03-0.06W per diode), with an electro-optical power conversion rate close to 100%. Under the same lighting effect, they save more than 80% energy compared to traditional light sources; 3. Recyclable: LEDs have better environmental benefits, with no ultraviolet or infrared rays in the spectrum. The waste is recyclable, pollution-free, and contains no mercury, making them safe to touch and a typical green lighting source.
7
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.