How to Fold Down the Rear Seats of the New Passat?

2 Answers
Valeria
07/30/25 1:21am
Here are the steps to fold down the rear seats of the New Passat: 1. Locate the back of the rear seats, where there are three square holes below the rear windshield. 2. Open the cover of the middle square hole. 3. Insert an object approximately the length of a key into the hole. 4. Move the object horizontally to the right to shift the internal mechanism to the right side. 5. Fold down the seat. Below is a brief introduction to split-folding and full-folding rear seats: (1) Split-folding rear seats refer to the backrests being foldable in a certain ratio. Compared to full-folding rear seats, split-folding offers greater flexibility, allowing half of the backrest to be folded down to accommodate large items while the other half remains usable for seating. (2) Full-folding rear seats mean the backrest is a single unit. When transporting large items that require more space, the entire rear seat backrest can be folded down to maximize cargo capacity. The downside of full-folding rear seats is that when folded, the rear seats cannot accommodate passengers.
Was this review help?
4
0
Share
DelEmilia
08/15/25 6:59am
As a car owner, I find folding down the rear seats in my new Passat quite simple. First, locate a plastic handle or button at the shoulder area of the seat, usually in black or gray, and gently pull it until you hear a click indicating successful unlocking. Then, slowly push the backrest forward with your hand until it lies flat on the rear floor, significantly increasing trunk space. Be sure to maintain stability during the operation and avoid sudden excessive force to prevent hand injuries. I often use this method when moving large items or loading travel gear, finding it very convenient. If the seat gets stuck or won't lie flat, it might be due to debris underneath or a rusty locking mechanism—clear any obstructions and try again. It's advisable to regularly check if the pull cord is aging or broken to avoid issues at critical moments. Overall, the Passat's design is thoughtful, allowing one-touch operation that saves time and effort.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

Why is the fuel consumption of Geely Vision X6 so high?

The reasons for the high fuel consumption of Geely Vision X6 are as follows: 1. Poor driving skills: The same car driven by different people will have different fuel consumption. Vehicles that are driven aggressively for a long time have significantly higher fuel consumption. Sudden braking or accelerating can increase fuel consumption by up to half compared to smooth driving. The difference between city roads and highways is also quite noticeable. Experienced drivers can still manage it reasonably. Only by summarizing experience and improving driving skills can the high fuel consumption caused by poor driving techniques be resolved. 2. Low tire pressure: If the car is not inflated for a long time, it will increase the friction between the car and the ground. Greater friction requires more power to move the vehicle, thus increasing fuel consumption. The simplest way to check tire pressure, besides the vehicle's built-in pressure detection device, is to feel the heaviness of the steering wheel. 3. Excessive engine carbon deposits: Carbon deposits caused by the chemical reactions of car fuel are almost unavoidable for all fuel-powered vehicles. If left untreated for a long time, it will not only increase fuel consumption but also degrade engine performance, leading to various issues such as idle shaking, poor acceleration, and excessive exhaust emissions. Adding a cleaning agent to the gasoline can help, but it is recommended to go to a 4S shop for a thorough cleaning. 4. Oxygen sensor failure: Once the oxygen sensor fails, the computer of the electronic fuel injection system will not receive information about the oxygen concentration in the exhaust pipe, damaging the engine and significantly increasing fuel consumption. The aging of the oxygen sensor is inevitable, so it is recommended to check and replace it at around 80,000 km. 5. Spark plug failure: If the spark plug fails to ignite the fuel effectively, it will lead to incomplete combustion, increasing unnecessary fuel consumption and causing adverse consequences such as carbon deposits. The recommended solution is to go directly to a 4S shop for replacement.
18
2
Share

Is it okay to rev up to 4000 RPM for overtaking in a new car?

For a new car within 5000 kilometers, using 4000 RPM for overtaking will definitely harm the vehicle and affect engine break-in. Even for cars with tens of thousands of kilometers, prolonged high-RPM driving should be avoided as it increases fuel consumption. Occasionally revving up to 4000 RPM or higher for a short distance can be beneficial for the engine. Not only does it not increase wear, but it also helps remove carbon deposits and reduce engine carbon buildup, a process known as "running-in at high speed." During high-speed driving, when speeds are typically maintained between 80~100 or even 100~120 km/h, the engine operates in an optimal state. This allows for complete combustion of gasoline, minimizing engine damage and ensuring the engine runs in its best condition. Besides gasoline, other components like lubricants also achieve their optimal operating state.
5
3
Share

How many liters of engine oil does a BMW 525 require?

The BMW 525Li requires 6.5 liters of engine oil. Engine oil serves multiple functions including lubrication, cleaning, cooling, sealing, friction reduction, rust prevention, and corrosion protection for the engine. Here are some important considerations when changing engine oil: 1. Draining oil while hot: Oil flows better when warm, allowing it to drain more completely from the oil pan. However, be cautious of excessive heat to avoid burns. 2. Maintain proper oil level: The oil quantity should be strictly maintained between the lower and upper marks on the dipstick. 3. Oil change interval: The oil change interval should be determined based on vehicle condition, road conditions, oil quality, and driving habits. 4. Oil quality selection: Choose oil based on driving environment, driving frequency, and the engine's specific requirements. It's better to use higher quality oil than lower. 5. Use of additives: Common engine oil additives include antioxidants, anti-wear agents, detergents, dispersants, foam inhibitors, and anti-corrosion/rust agents. Finished engine oils already contain these components in proper proportions. Unless you're a professional, avoid altering the oil's formulation as it may lead to unpredictable consequences or damage.
3
0
Share

What Material is the Backing Paper of Color Change Film?

Automotive color change films are generally made of three materials: PVC, TPU, and Vinyl. Introduction to PVC Material: PVC, also known as polyvinyl chloride, has been extensively researched and tested for use in automotive color change films primarily because its inherent hardness provides protection to the car body. However, this level of protection gradually diminishes over time due to exposure to wind and sunlight, weakening the material's quality. Therefore, even with color change film applied, proper maintenance is still necessary. Introduction to TPU Material: The greatest advantage of TPU material is that it maintains excellent protective performance for the car body even in extremely cold or hot environments, while also causing minimal damage to the film itself. Most color change films made from this material are produced by foreign brands. Introduction to Vinyl Material: Vinyl, also known as ethylene, was first invented and used by the American brand SAQETH, a pioneer in the world's top automotive modification and decoration industry. Vinyl is durable, flexible, and easy to use, offering a wide range of colors and surface finishes. Vinyl films can produce color change products that look as good as or even surpass high-quality paint finishes.
5
4
Share

What could be the reason for the engine being noisier than before?

It may be caused by aging engine mounts. After accumulating high mileage, the engine mounts can deteriorate, and replacing them should resolve the issue. Carbon buildup can also lead to increased engine noise. If the engine sounds normal during operation but the noise inside the car feels excessive, it indicates poor sound insulation. In this case, check the vehicle's sealing strips for signs of aging or consider enhancing the sealing to reduce noise. Increased engine noise is a common occurrence in high-mileage vehicles, and while owners need not worry excessively, they should pay closer attention to maintenance. If the engine produces a dull, slapping sound during operation, it could indicate an issue with the cylinder valves. In such cases, if the noise disappears at high speeds, it is likely due to valve problems. Additionally, check the oil pressure to rule out any related issues.
5
4
Share

What Causes Engine Power Loss When Accelerating at High Temperatures?

Engine power loss when accelerating at high temperatures can be attributed to the following reasons: Fuel system faults: A clogged or waterlogged air filter reduces air intake, leading to an overly rich air-fuel mixture, incomplete combustion, and poor acceleration. In this case, the exhaust pipe emits heavy black smoke. Cracks in fuel lines or loose/leaking connections, along with insufficient fuel pump pressure, result in poor fuel delivery and affect acceleration performance. Poor atomization or clogging of fuel injectors causes cylinders to misfire or stop working, impacting acceleration. The exhaust pipe may emit black smoke. Fuel quality is another factor. If the fuel contains excessive water, the exhaust pipe will emit white smoke. Electrical faults: Malfunctioning air flow meters reduce air intake, causing the air-fuel mixture to become overly rich or lean, affecting acceleration. Damaged spark plugs in individual cylinders (i.e., cylinder misfire) also impair acceleration. Additionally, issues like leaking ignition wires can contribute. Mechanical faults: Wear and tear of engine valves, cylinder liners, pistons, or piston rings result in insufficient cylinder compression. Excessive intake valve clearance or insufficient exhaust valve clearance can also cause problems.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.