How to fold down the rear seats of Mazda CX4?

1 Answers
McZane
07/29/25 12:35pm
CX4 rear seat folding methods are as follows: 1. Using the remote handle: 1. First, lower the headrest all the way down, down, down; 2. Check and confirm there are no items on the rear seats or in the cup holders, open the rear hatch and pull the remote handle to lower the seat back you want to fold. 2. Using the push button: 1. First, lower the headrest all the way down; 2. Then press the button to fold down the seat back. Precautions: 1. When folding the seat back forward, always support the seat back with your hand to avoid injuring your fingers or hands; 2. Before folding the seat back with the remote handle, ensure there are no cups in the rear cup holders, otherwise, the seat bottom and back may get dirty or damaged; 3. Be cautious when using the remote handle: (1) On a downhill slope, the seat back may fold forward faster than on flat ground; (2) On an uphill slope, the seat back may not fold up. If the remote handle cannot fold the seat back, you can pull the rear seat back forward from inside the car. 4. Before folding the rear seat backs, check the position of the front seats. Depending on the front seat position, they may collide with the rear seat backs, scratching or damaging the front seats or their pockets. If necessary, the headrests can be removed.
Was this review help?
9
3
Share
More Forum Discussions

Where is Ora produced?

Ora's research and development and design teams come from countries such as Germany, Austria, the United States, Japan, and South Korea. At the same time, Ora has international suppliers like Bosch and Autoliv. Below is relevant information about Ora: Introduction to Ora: The Ora brand belongs to Great Wall Motors and is the first independent new energy vehicle brand among mainstream Chinese automakers. Among Chinese automotive companies, Great Wall was the first to establish new energy vehicle operations as an independently managed new energy brand. Ora's advantages: The Ora brand is the result of Great Wall Motors' decade-long dedicated research and development, avoiding "oil-to-electric" conversions and "policy vehicles." Leveraging decades of Great Wall's technological expertise, the first original pure electric vehicle model, the Ora iQ, was created, providing consumers with more green mobility options while ensuring quality that stands up to scrutiny.
18
2
Share

What Causes a Car Tire to Burst on the Highway?

Here are the specific reasons for tire bursts on highways: 1. Low tire pressure: When tire pressure is too low, the wheel's sinking amount increases, radial deformation increases, friction between the tire surface and the ground rises, rolling resistance increases, and the internal stress of the tire body also rises. This causes the tire body temperature to rise sharply, the tire surface rubber to soften, and the aging speed to accelerate, leading to local delamination of the tire body and increased wear on the tire surface. Under these conditions, if the car continues to drive at high speeds on the highway, the above reactions of the tire will accelerate, significantly increasing the likelihood of a tire burst. 2. Over-inflation of the tire: When tire pressure is too high, the tension on the tire body cords increases, accelerating the fatigue process of the cords. Especially when driving with over-inflation, overload, and overspeed, the internal stress on the cords increases further, the tire temperature rises rapidly, rubber aging speeds up, and fatigue strength decreases. This results in severe wear on the central part of the tire surface, sawtooth-like wear on the side tread patterns, and cord layer breakage, leading to a tire burst. 3. Incorrect tire installation: Wheel imbalance. Due to uneven mass distribution across different parts of the wheel, when the wheel rotates, a huge impact force is generated in the wheel's rotation plane under centrifugal force, causing the wheel to bounce and sway. This accelerates tire wear and subjects the cord layers to periodic impact loads, reducing the cord's fatigue resistance. Particularly at speeds above 100 km/h, the wear caused by wheel imbalance is extremely severe, ultimately leading to a tire burst.
3
0
Share

What does the exclamation mark symbol on a new energy vehicle mean?

The appearance of this symbol indicates a fault in the power system of the new energy vehicle, which may prevent the vehicle from starting or charging. You can connect a fault diagnostic tool to perform a diagnosis on the vehicle's power system to identify the cause of the fault. Below is relevant information: 1. Triangle with an exclamation mark: This light indicates a general fault. Reasons for its illumination include: faulty exterior light bulbs; parking sensor malfunction; traction control system warning or fault; fuel cutoff system intervention or malfunction; engine oil pressure sensor fault; overheating of the dry dual-clutch transmission clutch. 2. Exclamation mark inside a circle with parentheses: This light is the brake system warning light. It may illuminate under the following circumstances: it lights up for a few seconds after turning on the ignition and turns off after starting the engine; it lights up when the handbrake is engaged and turns off when released; low brake fluid level, lighting up while driving; brake system malfunction. 3. Exclamation mark with a horizontal line under parentheses: This light is the tire pressure monitoring warning light. It illuminates when the pressure in one of the vehicle's tires is too low.
3
5
Share

Will the demerit points be reset after renewing the driver's license?

Demerit points will not be reset after renewing the driver's license upon expiration. This is because the calculation of demerit point clearance is based on the driver's license scoring cycle, not on whether the license has been renewed. Below is additional information: 1. Renewal rules: If a motor vehicle driver has not accumulated 12 or more demerit points in any scoring cycle during the six-year validity period of their driver's license, they will be issued a driver's license with a ten-year validity period. If they have not accumulated 12 or more demerit points in any scoring cycle during the ten-year validity period, they will be issued a long-term valid driver's license. 2. Renewal time: A motor vehicle driver should apply for renewal at the vehicle management office of the issuing location or elsewhere within 90 days before the expiration of their driver's license. 3. Demerit point clearance rules: According to regulations, if a motor vehicle driver has not accumulated 12 or more demerit points in a scoring cycle and has paid all fines, the demerit points will be cleared. If fines remain unpaid even if the demerit points are below 12, the points will carry over to the next scoring cycle.
13
1
Share

What are the dimensions of the Murano?

Nissan Murano has a length, width, and height of 4897X1908X1691mm, with a wheelbase of 2830mm. The Murano is a mid-size SUV under Dongfeng Nissan. Here are the details about the Murano: Specific configuration: The Murano is equipped with a 2.5T supercharged engine, codenamed QR25DER, with a maximum horsepower of 245. Additionally, Nissan has also equipped the Murano with an HEV hybrid system, which means the Murano boasts good fuel efficiency, along with its decent off-road capability, spacious interior, and brand reputation. Advantages: As an SUV model, the Dongfeng Nissan Murano performs commendably in terms of exterior design, power, and handling, attracting many consumers. It performs adequately in terms of power, with agile throttle response and good acceleration; the gear shifts are smooth, and the power output is gentle yet powerful.
7
5
Share

How to Replace the Air Filter in an Atenza?

Below are the detailed steps for replacing the air filter in an Atenza: 1. Open the car's engine hood, then locate the lower left corner of the engine compartment near the left front wheel. You will see a square plastic box. 2. Lift the clips around the plastic box and remove it to reveal the air filter. 3. Replace it with a new air filter, completing the entire process of replacing the Atenza's air filter. Here is some additional information about air filters: An air filter is a type of filter, also known as an air cleaner. Along with the cabin air filter and oil filter, it is referred to as one of the three filters. Depending on the type, air filters can be categorized into filtration-type air cleaners, centrifugal-type air cleaners, oil-bath-type air cleaners, and composite-type air cleaners, among others.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.