How to Fold Down the Rear Seats in the Envision?

1 Answers
LauraLee
07/29/25 11:00pm
Here are the steps to fold down the rear seats in the Envision: 1. Move the front seats forward. 2. First, retract the rear seat armrest. 3. Stow the seatbelt buckle of the middle rear seat. 4. Lower the headrest to its lowest position. 5. Pull the seat folding switch located on the shoulder of the rear seat to fold it down. Here are the methods to adjust the front seats in the Envision: 1. Lift/Press the seat cushion adjustment switch to raise/lower the seat cushion height. Moving the switch forward or backward allows the seat to move forward or backward. 2. Adjust the backrest tilt angle by pulling forward or backward—push forward to tilt forward and pull backward to tilt backward. 3. Press the lumbar support button to adjust the lumbar support angle.
Was this review help?
1
5
Share
More Forum Discussions

Does the 6-year exemption for new vehicle inspections include the 6th year?

The 6-year exemption for new vehicle inspections does not include the 6th year. Vehicles must undergo an on-site inspection in the 6th year. The 6-year exemption only means no on-site inspection is required, but vehicle owners must collect the inspection decal from the traffic management department every 2 years. Vehicles eligible for the 6-year exemption include non-commercial large, compact, and subcompact cars, as well as non-commercial compact and subcompact passenger vehicles. If the vehicle does not fall into these categories, it must undergo on-site inspections as scheduled. Vehicle annual inspection, also known as motor vehicle inspection, varies in terms of inspection items and scope depending on the vehicle's usage. According to the definition of motor vehicle inspection institutions under the evaluation of inspection and testing institution qualification certification, motor vehicle inspections include three categories: motor vehicle safety technical inspection, motor vehicle emission inspection, and comprehensive vehicle performance inspection.
14
2
Share

How to Deal with Brake Noise in Volkswagen Sagitar?

Brake noise in Volkswagen Sagitar is mostly a symptom of brake pad wear. The following are the causes of brake noise and solutions: 1. Cause 1: A sharp noise when braking. Solution: Check the brake pads to see if they are worn out or if there are any foreign objects. If the brake pads are worn out, they should be replaced immediately. If there are foreign objects, remove the brake pads, take out the foreign objects, and reinstall them. 2. Cause 2: A dull noise when braking. Solution: Check the brake caliper to see if there is wear on the sliding pins or if the spring plates have fallen off. If found, replace them immediately. 3. Cause 3: A hissing sound when braking. Solution: Check whether there is any problem with the friction between the caliper, brake disc, and brake pads. 4. Cause 4: A rattling sound when braking. Solution: Check whether the attachments on the brake pads are loose. The best method is to reinforce or replace the brake pads.
17
1
Share

Is Piston Ring Release Agent Harmful to the Engine?

Engine internal cleaner, also known as cleaning fluid, is an automotive maintenance product used to remove harmful substances such as sludge, carbon deposits, and gum from inside the engine, keeping the engine interior clean, enhancing oil fluidity, reducing wear, and extending the engine's service life. Below is extended information about release agents: Introduction: Engine cleaning involves both internal and external parts. The external part of the engine is exposed in the engine compartment and is generally cleaned less frequently. Therefore, the commonly referred engine cleaner is the internal engine cleaner, or cleaning fluid, designed to remove harmful substances like sludge, carbon deposits, and gum from inside the engine, maintaining internal cleanliness, improving oil flow, reducing wear, and prolonging the engine's lifespan. Due to the precision of engine construction, engine cleaning is typically performed without disassembly, hence the term "no-disassembly engine cleaner."
8
3
Share

Why does the Ford Focus clutch draw in air?

Ford Focus clutch draws in air due to clutch slave cylinder failure or pipeline damage. Below is an introduction to the symptoms of clutch damage: 1. Clutch slippage. When starting the car in low gear, after releasing the clutch pedal, the car cannot start or has difficulty starting; during acceleration, the vehicle speed cannot increase with the engine speed, resulting in a feeling of weak driving, and in severe cases, causing phenomena such as burnt odor or smoke. 2. Incomplete clutch disengagement. Even when the clutch pedal is fully depressed, the power between the clutch's driving and driven discs cannot be completely cut off, leading to difficulty in shifting gears, gear grinding, or inability to stop, as well as clutch overheating. 3. Clutch shudder. The entire vehicle shakes during startup, especially at idle speed when gradually releasing the clutch pedal in low gear, causing continuous jerking. 4. Abnormal clutch noise. When the clutch pedal is slightly depressed, as the inner end face of the release bearing just contacts the release lever, the clutch emits a continuous "scratch, scratch, scratch" sound; noise occurs during engagement at startup or separation while driving, accompanied by shaking.
17
2
Share

What is the tire model of the Trumpchi GS8?

The tire model specification is 255/50R20. The first number 255 represents the tire width of 255MM, 50 indicates the aspect ratio of the tire section is 50%, meaning the section height is 50% of the width, and 20 stands for the rim diameter of 20 inches. The middle letters or symbols have special meanings: "X" denotes high-pressure tires; "R" and "Z" represent radial tires; "—" indicates low-pressure tires. The fuel consumption per 100 kilometers is 5.3L. In addition to the model, the tire also displays the following common data: Tire cord material: Indicated by Chinese pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under specified conditions. Letters A to Z represent the certified speed ratings of tires from 4.8km/h to 300km/h. Commonly used speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: Indicates the rim specification compatible with the tire for practical use, such as "Standard rim 5.00F".
2
5
Share

Where is the handbrake of the Mercedes-Benz C260?

The Mercedes-Benz C260 is equipped with an electronic handbrake. The P symbol with a circle located to the left of the automatic gear lever is the handbrake of the Mercedes-Benz C260. After stepping on the brake, shift to P gear and pull this button to engage the handbrake and lock the wheels. Here is some additional information:1. Older traditional cars usually use mechanical handbrakes, but now most cars have started to adopt electronic handbrakes.2. The Mercedes-Benz C-Class models all feature electronic handbrakes, which do not require manual operation. The handbrake is automatically engaged when the engine is turned off and the doors are closed.3. If manual operation is desired, press the button marked with a P symbol located below the left side of the steering wheel to engage the handbrake, and pull it to release the handbrake. When shifting to P gear and turning off the engine, the dashboard will automatically display a P symbol, indicating that the electronic handbrake has been automatically engaged. For temporary stops, you can shift to N gear and manually press the electronic handbrake.4. The electronic handbrake is a technology that achieves parking braking through electronic control.
15
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.