How to Fix Water Leakage in the Door of an Old Lavida?

1 Answers
RoseRose
07/30/25 3:55am
Solutions for water leakage in Lavida's door: Gently pry open the strip at the bottom of the door, and you will see a square drainage outlet. If the car hasn't been cleaned for a long time, some mud and debris might have accumulated. Use a flat-head screwdriver to remove all the clogged debris, allowing the water to drain out. Reasons for water leakage in the door of an old Lavida: 1. The drainage outlet at the bottom of the door is clogged, preventing water from draining. 2. The door seal strip is not tightly sealed, causing water to leak into the door. 3. The waterproof membrane inside the door is damaged, allowing water to flow directly onto the threshold trim and then onto the floor mat.
Was this review help?
1
0
Share
More Forum Discussions

Is the Refine M3 really fuel-consuming?

The Refine M3 is not fuel-consuming. The combined fuel consumption (highway + city) of the Refine M3 is only 9.4L/100km, while the highway fuel consumption is around 7.8L. Here is some extended information about the Refine M3: 1. In terms of driving experience: The Refine M3 is equipped with a 1.6L naturally aspirated engine, delivering a maximum horsepower of 120Ps. The torque data of the Refine M3 is 150Nm, and it takes only 12 seconds to accelerate from zero to 100km/h, which is comparable to the acceleration data of the Nissan NV200. 2. In terms of space: The Refine M3 is a 4-door, 7-seater MPV, and its space features are quite prominent. The body dimensions are 4645*1740*1900mm, which ensures a spacious interior. The body width reaches 1740mm, providing good lateral space, and even when fully loaded in the rear seats, the space remains very comfortable.
18
4
Share

What is the actual fuel consumption of the Nissan Patrol?

The actual fuel consumption of the Nissan Patrol is: 14.7L and 16L per 100 kilometers for combined fuel consumption. Below is a related introduction to the Nissan Patrol's configuration: 1. Safety features: Anti-lock braking system, brake force distribution, brake assist, traction control, body stability control, driver airbag, passenger airbag, tire pressure monitoring, rear child seat interface. 2. Auxiliary configurations: Cruise control, hill start assist, hill descent control, front parking radar, rear parking radar, driving mode selection, smart entry, keyless start, dual-zone automatic air conditioning, multifunction steering wheel, air purification, in-car refrigerator, etc. 3. Chassis and braking: The front and rear suspensions of the Nissan Patrol models currently on sale are both double-wishbone independent suspensions, with a front-engine four-wheel-drive mode, and the four-wheel-drive system is full-time four-wheel drive. The front and rear brake types of the Nissan Patrol models currently on sale are both ventilated disc brakes, and the parking brake type is foot-operated.
20
4
Share

How to use the lights on Audi A3?

Audi A3 light usage instructions are as follows: 1. Turn signals and parking lights: With the ignition switch on, rotate the control lever to the corresponding turn or parking light position to activate the respective lights. If the lever is only tapped briefly, the lights will flash three times. 2. High beam and high beam flash function: Move the control lever to the corresponding position, and the high beam indicator will illuminate in the instrument cluster. 3. Fog light activation: The fog light switch is located below the left side of the steering wheel. To turn on the lights, simply press the corresponding button. 4. Automatic headlights, low beam, and position lights: When the AUTO button is lit, it means the automatic headlights are currently activated. With the AUTO button lit, press once to turn on the low beam, press a second time to turn on the position lights, and press again to turn off the lights. 5. Headlight cleaning: With the headlights on, activating the windshield washer switch will spray and clean the headlights. With the headlights off, activating the windshield washer switch will only clean the windshield. 6. Adaptive headlights: Adjust to the AUTO position.
8
1
Share

What issues should be paid attention to in Subject 2?

Precautions for Subject 2 test: 1. Mock test: The purpose of the mock test is to familiarize the candidate with the test environment, and at the same time, the coach can guide on the points where marks are easily deducted. Therefore, the mock test is absolutely essential, and full preparation is necessary to best face the challenge. 2. Relax: Dress comfortably before the test and be mentally prepared; pay attention to the key points when reversing into the garage, do not turn left or right; when parking in a side position, ensure the rear wheel exceeds the edge line of the garage, adjust the distance properly, remember to turn on the turn signal and honk the horn. When making a sharp turn, steer the wheel decisively after aiming at the correct position; when driving on a curve, make a wide turn after entering the curve, maintain a steady speed, and avoid crossing the line in all the above situations. 3. Pay attention to signing: After the test, drive the car back to the starting position, sign the confirmation, and then turn off the engine. 4. Bring your ID card: You must bring your ID card to the test, as you cannot take the test without it. After so much preparation, do not let the lack of an ID card prevent you from taking the test. Additionally, make sure to turn off your phone during the test, as any sound from the phone will be considered cheating.
10
3
Share

How much does the LaCrosse weigh?

LaCrosse body weight: 1770 kg. Below is relevant information about the LaCrosse: 1. Body dimensions: Length 5031mm, width 1853mm, height 1458mm, wheelbase 2807mm. 2. Powertrain: The LaCrosse offers three engine options: 2.0T, 2.4L, and 3.0L. The US-imported ECOTEC D-VVT 2.4L all-aluminum four-cylinder engine is a new member of General Motors' global ECOTEC engine family. This 16-valve engine features a D-VVT dual electronic variable valve timing system, delivering maximum power of 125kW/6400rpm and maximum torque of 225Nm/4800rpm, with 90% peak torque available as low as 2400rpm. Benefits include the lightweight advantage of the all-aluminum engine, excellent characteristics of D-VVT dual electronic variable valve timing, along with technologies such as multi-point sequential fuel injection (SFI), electronic throttle control (ETC), dual counter-rotating balance shafts, oil-cooled piston jets, maintenance-free automatic adjusting all-steel timing chain, and 32-bit engine control module.
12
3
Share

Where is the Crankshaft Positioning Hole on the Roewe 550?

The crankshaft positioning hole on the Roewe 550 is located next to the crankshaft position sensor and the crankshaft pulley. The crankshaft is the most critical component in the engine, bearing the force transmitted by the connecting rod and converting it into torque, which is then output through the crankshaft to drive the engine's accessories. Below is relevant information: 1. Crankshaft: The crankshaft is subjected to the combined effects of centrifugal force from rotating masses, periodically varying gas inertia forces, and reciprocating inertia forces, causing it to endure bending and torsional loads. Therefore, the crankshaft must have sufficient strength and stiffness, with wear-resistant journal surfaces, uniform operation, and good balance. 2. Crankshaft Journals: To reduce the mass of the crankshaft and the centrifugal force generated during operation, crankshaft journals are often hollow. Oil holes are drilled on each journal surface to allow oil to flow in or out for lubricating the journal surfaces. To minimize stress concentration, transition arcs are used at the connections between the main journals, crankpins, and crank arms. The crankshaft counterweights (also known as balance weights) function to balance the rotating centrifugal forces and their moments, and sometimes also to balance reciprocating inertia forces and their moments.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.