···
Log in / Register

How to Fix the Random Jumping of the Excelle's Central Lock?

5 Answers
StJayla
07/29/2025, 03:39 AM

The repair method for the random jumping of the Excelle's central lock is: go to a 4S shop to replace the door lock control assembly and the central control module. The central lock, whose full name is central control door lock, is a car accessory composed of a door lock switch, an actuator, and a controller. The Excelle is a compact car with a body size of: length 4468mm, width 1765mm, height 1469mm, a wheelbase of 2611mm, and a fuel tank capacity of 40l. The Excelle is equipped with a 1.3l naturally aspirated engine, with a maximum power of 79kw at 6200rpm, and a maximum torque of 133nm at 4000rpm.

Was this review help?
7
3
Share
Carlos
08/12/2025, 09:46 PM

I've been driving my Excelle for several years, and the central locking system acting up is a common issue. I've encountered it myself multiple times. It's particularly prone to happening in rainy or humid conditions, where the locks keep cycling on and off uncontrollably when trying to lock the doors. This could be due to aging door lock actuators causing sticky switches or moisture-induced short circuits at wiring connections. For a quick DIY fix: Check the fuse box under the driver's seat, locate the central locking fuse, and replace it if blown. If that doesn't work, disconnect the car battery for a few minutes to reset the system. For a permanent solution, you'll need to remove the door panel to clean the actuator contacts - rust buildup is frequent in Excelle models here. If problems persist, have a professional diagnose the control module; don't delay repairs as unexpected locking while driving could be dangerous. Remember to maintain door systems regularly to prevent issues.

Was this review help?
20
4
Share
Expand All
HavenRose
10/04/2025, 04:21 AM

If you notice the Buick Excelle's central locking system acting erratically, don't panic. I've handled similar cases where the fault lies in either the door lock switch or actuator. Worn switch contacts can become sticky and trigger randomly; a faulty actuator motor will cause repeated cycling. First check battery voltage - low voltage can cause system errors and reboots. Inspect wiring connectors for looseness, and use a multimeter for accurate short circuit testing. The Excelle's door system is prone to moisture corrosion - cleaning connections might solve it. Replace components if necessary (actuators are inexpensive, costing just a few dozen yuan). General troubleshooting steps: start with fuses, then test individual components. For prevention, maintain interior dryness and minimize electronic interference sources.

Was this review help?
11
2
Share
Expand All
SanMiles
11/17/2025, 10:08 PM

As a new car owner, my Excelle's central locking system once acted up randomly, feeling like it was haunted. I first checked the manual—the fuse labeled 'lock' in the box under the passenger seat was replaced as a test, which sometimes worked. If that didn’t help, it might be a switch malfunction or actuator jamming. You can try removing the door trim panel, but don’t force it if you’re unfamiliar. My first attempt fixed it by cleaning the contacts—moisture was the culprit. If DIY isn’t your thing, a repair shop can handle it in about an hour at a reasonable cost. When washing the car, avoid spraying too much water into door gaps. Remember: safety first—park properly before repairs to avoid disrupting daily driving.

Was this review help?
1
0
Share
Expand All
VonLucille
01/07/2026, 11:45 PM

Random central locking malfunctions are no minor issue—they directly impact driving safety. My Excelle once kept locking and unlocking unexpectedly on the highway, which was terrifying! I immediately pulled over to inspect it. Common causes include aging wiring, damaged switches, or unstable power supply to the control module. It's advised to stop using the vehicle immediately: first check the corresponding fuse in the fuse box, then inspect whether the door lock actuator is sticking and needs cleaning or replacement. Excelle models are prone to oxidized wiring connectors—clean them or use a moisture remover for improvement. Prevention is crucial: regularly apply anti-rust spray and conduct vehicle inspections. If this occurs repeatedly, have a professional workshop diagnose the module to prevent dangerous door lock failures. Never underestimate this issue—timely repairs ensure personal safety.

Was this review help?
14
0
Share
Expand All
More Forum Discussions

Can Transmission Noises Be Repaired?

Transmission noises can be repaired. Once an automatic transmission malfunctions, the vehicle owner should promptly send it for repair. If abnormal noises are ignored and the vehicle continues to be used, it may eventually lead to the vehicle not moving or even complete transmission failure. Therefore, once a transmission issue arises, it must be taken to a professional transmission repair facility immediately to avoid greater losses. The main causes of abnormal noises in an automatic transmission include: excessive wear of the oil pump or improper transmission fluid level (too low or too high), noise from the torque converter due to damaged lock-up clutch or one-way overrunning clutch in the guide wheel, noise from the planetary gear set, or noise from shift actuators. Solutions for transmission noises: Check the automatic transmission fluid level; if it is too high or too low, adjust it to the correct level. Use a lift to raise the vehicle, start the engine, and check the source of the noise in neutral, drive, reverse, and other gears. If there is continuous noise at the front of the transmission in all gears, it is usually due to the oil pump or torque converter. In such cases, the transmission should be disassembled for inspection. Check the oil pump for wear and the torque converter for excessive friction debris. Replace the oil pump or torque converter if abnormalities are found.
14
4
Share

What is the difference between SN and SP engine oil?

Differences in viscosity (phosphorus content); Different advantages. Below is the relevant introduction: Viscosity (phosphorus content): SN engine oil has relatively lower phosphorus content; and the viscosity of SP oil is slightly higher compared to SN. Different advantages: SP oil film is stronger than SN, providing better protective performance. Additionally, SP shows stable improvements over SN in terms of noise reduction, fuel consumption, and acceleration performance. Synthetic oil: Synthetic oil is manufactured by humans using chemical methods. Depending on the intended use, the composition of synthetic oil can be adjusted. The development of synthetic oil began in the 1930s. At that time, due to the demanding conditions of aircraft engine oil, which required higher performance, some chemical plants began to develop and produce synthetic oil.
12
3
Share

What Causes Loud Engine Noise During Acceleration?

Reasons for loud engine noise during acceleration: 1. Dirty air filter, old spark plugs, damaged ignition wires, or contaminated gasoline; 2. Issues with the fuel filter, carburetor, or fuel pump components; 3. Engine overheating, clogged exhaust system, or vacuum tube leakage; 4. Lack of power steering fluid, damaged generator bearings, or problems with the power steering pump and water pump. The engine is the device that provides power to the car, determining its power performance, fuel economy, stability, and environmental friendliness. Engines are categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrid systems. The working principle of a gasoline engine is based on the four-stroke cycle.
14
1
Share

Should Fuel Additive Be Added Before or After Refueling?

It is more effective to add the fuel additive to the fuel tank before refueling. When the fuel level in the tank is low, adding the fuel additive and then refueling allows for better mixing of gasoline and the additive. Fuel additives, also known as gasoline additives, are primarily used to remove carbon deposits from the engine. However, some low-quality additives may not only fail to clean carbon deposits but could also damage the engine. The main function of fuel additives is to clean carbon deposits, which has always been their key product feature, along with additional benefits such as maintaining the engine and fuel system. Some specialized fuel additives can also improve the anti-knock properties (octane rating) of the fuel.
16
5
Share

What is the appropriate level to fill the coolant to?

Coolant should be filled to the midpoint between the upper mark (MAX) and the lower mark (MIN). Relevant information about coolant is as follows: Replacement cycle: The shelf life of automotive antifreeze is generally 2 years. Typically, ordinary household vehicles require antifreeze replacement every 2 years or after driving 40,000 kilometers. Introduction: Antifreeze, fully known as antifreeze coolant, refers to a coolant with antifreeze properties. It is a type of coolant containing special additives, primarily used in liquid-cooled engine cooling systems. Currently, over 95% of antifreeze used domestically and internationally is ethylene glycol-based aqueous antifreeze, characterized by a high boiling point, low volatility, moderate viscosity, minimal changes with temperature variations, and excellent thermal stability, making it an ideal coolant. The primary function of antifreeze is to remove excess heat from the engine cooling system while preventing the cooling water in the pipes from freezing and expanding in winter, which could lead to radiator damage.
14
3
Share

What is the 0-100 km/h acceleration time of the CFMoto 800MT?

The 0-100 km/h acceleration time of the CFMoto 800MT is 7 seconds. Here are some details about the CFMoto 800MT: Fuel consumption: Approximately 5 liters per 100 kilometers. For comparison, a typical 125cc household motorcycle consumes about 2.5 liters per 100 kilometers, while a 500cc motorcycle consumes around 4 liters. The CFMoto 800MT is a twin-cylinder, 800cc motorcycle with a fuel consumption of about 5 liters per 100 kilometers. In congested urban traffic conditions, this can increase to 6-7 liters, while on long-distance trips at a steady speed of 80-90 km/h, it can drop to around 4 liters. Power configuration: The CFMoto 800MT is equipped with a 799cc inline twin-cylinder liquid-cooled engine, delivering a maximum power of 70 kW (95 hp) at 9000 rpm and a maximum torque of 77 Nm at 6500 rpm.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.