How to Fix a Car Key That Won't Pop Out?

Why can't the Fengjun 5 complete the stationary self-cleaning?

Fengjun 5 cannot complete the stationary self-cleaning for the following reasons: 1. Particulate filter clogged: At this time, due to internal clogging of the DPF, the exhaust flow resistance is very high, which affects the normal operation of the engine. 2. Particulate filter full. Due to the generation of soot particles, the soot particles inside the DPF gradually increase, increasing the exhaust resistance, and the engine's fuel consumption and power are affected by the increase in exhaust back pressure. Below is an expansion of the particulate filter regeneration process: A large amount of soot particles accumulate inside the DPF, affecting the exhaust back pressure, making it difficult for the exhaust gas to be discharged, greatly limiting the engine's power and fuel economy. The engine control unit, based on the signal from the exhaust pressure sensor, controls the engine to perform the soot cleaning and regeneration process on its own, burning the soot particles accumulated inside the DPF at high temperatures.

15

2

Share

What is the structure of a throttle position sensor?

Linear output throttle position sensors consist of two contacts (or touch heads) linked to the throttle shaft. One contact slides along a resistor, converting throttle position signals into voltage values (VTA) through resistance changes. The other contact connects with the idle contact (IDL) when the throttle is fully closed. The IDL signal is used for fuel cut-off and ignition timing control. Additional information: 1. Throttle Position Sensor: The throttle position sensor, also known as a throttle opening sensor or throttle switch, primarily detects whether the engine is in idle, load, acceleration, or deceleration conditions. Essentially, it functions as a variable resistor with several switches, installed on the throttle body. 2. Resistor Shaft Linkage with Throttle: The resistor's rotating shaft connects to the throttle and features two contacts: a full-open contact and an idle contact. When the throttle is in the idle position, the idle contact closes, sending an idle condition signal to the ECU. In other positions, the idle contact opens, outputting voltage signals corresponding to different throttle angles. The ECU uses these signals to determine engine load and identify acceleration or deceleration based on voltage changes over time. Based on these conditions, the ECU adjusts fuel injection or implements fuel cut-off control.

16

4

Share

Why is the rear shock absorber of the new Santana very hard without oil leakage?

The rear shock absorber of the new Santana is very hard without oil leakage because the shock absorber value is incorrect and needs to be rematched using a computer. Purpose of shock absorbers: To accelerate the attenuation of vibrations between the frame and the body, thereby improving the driving smoothness (comfort) of the vehicle, most car suspension systems are equipped with shock absorbers. The shock absorption system of a car consists of both springs and shock absorbers. Shock absorbers are not used to support the weight of the vehicle body but to suppress the oscillations when the spring rebounds after absorbing shocks and to absorb the energy from road impacts. Working principle of shock absorbers: When relative motion occurs between the frame (or body) and the axle due to vibrations, the piston inside the shock absorber moves up and down, causing the oil in the shock absorber chamber to repeatedly flow from one chamber to another through different pores. At this time, the friction between the pore walls and the oil, as well as the internal friction between oil molecules, creates a damping force that converts the vehicle's vibration energy into heat energy of the oil, which is then absorbed by the shock absorber and dissipated into the atmosphere.

13

5

Share

What is the difference between 55w and 100w car bulbs?

The differences between 55w and 100w car bulbs are as follows: 1. Different power: The higher the power of the bulb, the brighter it is. The 55w low beam has lower power, while the 100w low beam has relatively higher power. 2. Different brightness: The 55w low beam is slightly dimmer, while the 100w low beam is brighter. Here is some extended information: 1. Bulb models: Bulb models include H1, H4, H3, H7, etc. Among them, H1 is a single-filament single-pin bulb, H7 is a single-filament double-pin bulb, and H4 is a dual-filament triple-pin bulb where both low and high beams are in one bulb. 2. Classification of xenon lights: Xenon lights are divided into six types based on bulb form: high beam with lens, low beam with lens (the above two types are generally used in original xenon light systems, such as PST, AUDI, etc.). Common bulb models include: H1 (for high beam), H3 (for fog lights), H4 (for combined high and low beam bulbs), and H7 (mostly for low beam).

3

1

Share

What are the reasons for the non-response of the Fengguang 580 one-button start?

The reasons for the non-response of the Fengguang 580 one-button start are as follows: 1. Key-related issues: For example, the key battery is dead, or the key's radio waves are being interfered with. If the car key is frequently placed near electronic devices such as mobile phones, computers, or televisions, it can easily cause interference with the low-intensity radio waves in the key, making it difficult for the car's sensor to detect the key. In such cases, the one-button start will not respond. 2. The gear is not in P (Park) position. For most car models, the engine cannot be started if the gear is not in P position. This is a safety design by the manufacturer to prevent the engine from starting when the gear is in D (Drive) or R (Reverse) position. 3. The brake pedal is not pressed. Many cars require the brake pedal to be pressed for the one-button start to activate the engine. If the brake pedal is not pressed, it only powers the car's electrical circuits, which can be dangerous. 4. Issues with the car itself. If the problem is related to the car, the scope of potential causes is broad, and it is advisable to visit a 4S store for a timely inspection.

1

3

Share

Where is the child lock located on the car door?

The car child lock, also known as the door lock child safety mechanism, is located on the rear door lock of the vehicle. When you open the rear door, you will find a small lever (safety mechanism) below the door lock. The function of the child lock is as follows: When children are seated in the rear seats, it prevents active and unaware children from opening the door during the journey, thereby avoiding potential dangers. If the rear door of the car cannot be opened from inside but can be opened from outside, it is highly likely that the child lock is engaged. This occurs when rear passengers accidentally activate the safety mechanism while getting in or out of the car. Simply reset it to resolve the issue.

17

0

Share

How to Fix a Car Key That Won't Pop Out?

Why can't the Fengjun 5 complete the stationary self-cleaning?

What is the structure of a throttle position sensor?

Why is the rear shock absorber of the new Santana very hard without oil leakage?

What is the difference between 55w and 100w car bulbs?

What are the reasons for the non-response of the Fengguang 580 one-button start?

Where is the child lock located on the car door?

What is the Shouqi Enjoy Model?

How many seats does the Volvo XC60 have?

Which Toyota model is the tv7181gl-id?

What is the fuel consumption of the Nissan Cedric A33?