···
Log in / Register

How to Fix a Black Screen in the Reversing Camera?

5 Answers
MadelineFitz
07/29/25 9:07am
The phenomenon of a black screen in the reversing camera is most likely due to poor line contact. It is necessary to promptly check the wiring and the connection points of the vehicle's installation to see if there are any loose connections. Relevant explanations are as follows: 1. If there are loose connections, it will naturally lead to intermittent functionality of the reversing camera, or even a complete black screen. In this case, simply reconnect the loose parts properly. It could also be due to aging of the video power cable. Try replacing it with a new one. If the black screen issue is resolved, it confirms that the problem was indeed with the video power cable. 2. If after checking the above two scenarios the reversing camera still shows a black screen, it is likely due to prolonged use of the reversing camera, resulting in poor chip photosensitivity. This not only causes a lot of snowflake-like interference but also leads to a black screen. It could also be due to defects in the vehicle's circuit design.
Was this review help?
6
3
Share
VanJameson
08/12/25 8:27am
I usually enjoy doing some car repairs myself. If the reversing camera screen goes black, the first thing to check is whether there is dust or any obstruction on the camera lens, such as mud or bird droppings. Then, open the engine hood or trunk, locate the wiring connected to the camera, and check if the connectors are loose—give them a gentle shake to test. If the wires are broken or the fuse is blown, the fuse box is usually located under the dashboard or in the engine compartment; just replace the corresponding fuse. If that doesn’t work, try restarting the car’s infotainment system—some models allow you to adjust the reversing camera mode in the settings. Don’t overlook the possibility of a short circuit caused by water leakage on rainy days, so regularly clean the rear of the car and keep it dry. If you still can’t fix it, don’t force it to avoid damaging other components. Always ensure the power is off for safety before attempting any repairs yourself.
Was this review help?
1
3
Share
Expand All
MargaretAnn
10/06/25 3:48am
I've encountered this situation before, and the black screen had me running around in circles. First, check if the camera lens is clean—wipe off any dirt if present. Then, inspect the trunk or fuse box—the reverse light fuse for most cars is located near the headlight fuse; replace it if blown. Next, jiggle the connector plug for the camera and tighten it if loose. If the issue persists, try restarting the car or resetting the infotainment screen settings. Remember, the camera might have been damaged from impact, so be careful not to scrape against obstacles when parking. If these steps don’t work, you’ll need to consult a professional technician to test the wiring with instruments or replace components.
Was this review help?
4
5
Share
Expand All
AdelineLee
11/19/25 5:14am
When I was a new driver, the screen suddenly went black while reversing, which scared me into stopping the car. A simple solution is to first wipe the camera lens to ensure there's no dirt obstructing it. If that doesn't work, try restarting the vehicle, wait a few minutes, and then shift into reverse gear again. If it still doesn't light up, check the rear wiring and plug it in tightly if it's loose. If you can't fix it yourself, don't take risks—call a friend for advice or drive to a repair shop. Remember, safety comes first when reversing; use the rearview mirror for assistance if there's no image. To prevent similar issues, avoid muddy roads to keep the camera from getting wet.
Was this review help?
14
1
Share
Expand All
AidenDella
11/19/25 5:16am
A black screen on the reversing camera is quite dangerous, so I always remind myself to handle it safely. Possible causes include camera malfunction, short circuits, or impact damage. First, manually check for loose lenses or connections. Then, test if the fuse is intact—it's located in the small box under the dashboard. If these are fine, it might be a display setting issue; try resetting the menu or selecting reverse mode. Don’t overlook the rear environment—rain can corrode wiring, so keep it dry to prevent issues. If repairs don’t work, get it fixed immediately to avoid compromising driving safety, and have the entire system, including the reversing radar, inspected while you’re at it.
Was this review help?
9
5
Share
Expand All
More Forum Discussions

What is the emission standard for vehicles from 2017?

Vehicles from 2017 comply with the China V emission standard. The full name of the China V standard is the National Fifth Stage Emission Standard for Motor Vehicle Pollutants. The emission control level of the China V standard is equivalent to the Euro 5 emission standard currently implemented in Europe. The European Union has been enforcing this standard since 2009, which imposes stricter limits on vehicle emissions such as nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter. From China I to China IV, each upgrade in the standard reduces vehicle pollution by 30% to 50%. Compared to the China IV standard, the China V standard reduces nitrogen oxide emissions from light-duty vehicles by 25% and from heavy-duty vehicles by 43%. Effects of implementing the China V standard: It promotes the improvement of domestic gasoline and diesel quality for vehicles, contributes to the reduction of pollutants from new vehicles, and improves the emission conditions of a large number of in-use vehicles.
15
3
Share

How to Change the Transmission Oil for Lavida?

Here are the steps to change the transmission oil for Lavida: 1. Start the engine and wait until it reaches normal operating temperature; 2. Loosen the oil drain plug with a wrench and use an oil pan to catch the old oil until it stops flowing. Then, run the engine for 30 seconds to allow the oil in the main oil passage to drain; 3. Remove the oil filter using a specialized wrench; 4. Apply some oil to the oil seal of the new oil filter and tighten it clockwise by hand; 5. Add new oil through the oil filler cap on the engine valve cover, typically filling up to three-quarters of the oil container; 6. Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs; 7. After stopping the engine, pull out the oil dipstick to ensure the oil level is within the standard range.
19
3
Share

How to Solve the EPC Light Issue in a Car?

The solutions for the EPC light issue in a car are as follows: 1. Check the throttle body: It might be clogged, so clean the throttle body immediately. 2. Inspect the wiring: This could cause the brake lights to malfunction, so check the brake switch and wiring. 3. Examine the fuel quality: Poor fuel quality can also trigger the EPC warning light, so it is recommended to use high-quality gasoline. If the EPC light is on but the vehicle shows no obvious signs of malfunction and can still be driven, the driver can try turning off and restarting the engine to turn off the EPC light. Even if there are no apparent issues, the driver should not take it lightly and should promptly have the vehicle inspected and repaired.
8
3
Share

Which country does the Citroën car brand belong to?

Citroën is a French automobile brand. Founded in 1919, Citroën became one of the two car brands under the PSA Peugeot Citroën Group in 1976. Here is an introduction about Citroën: 1. Dongfeng Citroën is a joint venture established in China by China's Dongfeng Motor Group and France's PSA Automobile Group. 2. Citroën is an automobile brand under the PSA Group and operates as an independent subsidiary domestically. 3. In 1976, Citroën Automobile Company merged with Peugeot to form the Peugeot Group, one of the top three automobile companies in Europe. 4. Citroën Automobile Company is the third largest automobile company in France, primarily producing passenger cars, light commercial vehicles, and mid-to-high-end automobiles.
2
3
Share

Why are Brabus cars so rare?

Here are the specific details about Brabus cars: 1. High-performance modified vehicles: Brabus cars are high-performance modified vehicles created by Brabus based on Mercedes-Benz models. Brabus spares no expense in modifications, going far beyond simple alterations to the original vehicle. Each model undergoes extremely strict quality control. Additionally, Brabus's exclusive test track allows for comprehensive testing of modified vehicles, ensuring the driving quality of every customized car. 2. Mercedes-Benz's official tuning partner: Although Brabus is not a subsidiary of Mercedes-Benz, it serves as the brand's official tuning partner. The modified Brabus models have set numerous performance records for factory-tuned vehicles, rivaling even the Mercedes-AMG series. Furthermore, all Smart Forfour modified vehicles worldwide are crafted by the Brabus tuning division.
18
5
Share

How to Replace the Air Filter Element in the New Mondeo?

New Mondeo air filter element replacement method is as follows: 1. Use tools to loosen the locking nut on the air filter box, open the cover, and you can see the appearance of the air filter element. 2. Take out the filter element to check the condition. If it is too dirty, it needs to be replaced. If it is not dirty, it can be cleaned and reused. 3. Install the new air filter element, paying attention to the direction of the filter element during installation. The following introduces the cleaning method of the Ford Mondeo air filter element: 1. The owner can use an air gun for operation. If not available, a hair dryer can be used as a substitute. 2. The filter element has good filtration capability. First blow impurities from the outside in, then blow from the back side of the intake direction, and finally dust off the surface dust by hand.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.