How to fill in the validity period of an electronic driver's license?

Where is the rearview mirror heating for the Lynk & Co 03 located?

The rearview mirror heating for the Lynk & Co 03 is located on the fourth button below the central control screen. The Lynk & Co 03 is a compact sedan with body dimensions of 4657mm in length, 1840mm in width, and 1460mm in height, with a wheelbase of 2730mm. The Lynk & Co 03 is equipped with three turbocharged engines: a low-power 1.5-liter turbocharged engine, a high-power 1.5-liter turbocharged engine, and a 2.0-liter turbocharged engine. The low-power 1.5-liter turbocharged engine has a maximum power of 115 kW and a maximum torque of 245 Nm; the high-power 1.5-liter turbocharged engine has a maximum power of 132 kW and a maximum torque of 265 Nm. The 2.0-liter turbocharged engine has a maximum power of 140 kW and a maximum torque of 300 Nm.

3

0

Share

Does replacing a car radiator make it an accident vehicle?

Replacing a car radiator does not classify the vehicle as an accident vehicle. The radiator, also known as the heat exchanger, is part of the car's cooling system and consists of an inlet chamber, outlet chamber, main plate, and radiator core. The functions of the car radiator are: 1. To absorb heat from the engine block and prevent the engine from overheating; 2. To use water as a heat transfer medium through the cooling water circuit, dissipating heat through large-area cooling fins via convection to maintain the engine's optimal operating temperature. The method for cleaning scale from a car radiator is: 1. Park the vehicle and turn off the engine, wait for the coolant temperature to drop, then open the expansion tank and add radiator cleaner; 2. Start the engine and let it idle for 5 to 10 minutes after the cooling fan activates; 3. Turn off the engine and remove the front bumper; 4. After the coolant temperature has completely cooled, drain the radiator cleaner along with the coolant; 5. Replace with new engine coolant.

9

4

Share

What is the correct way to press the accelerator?

The correct way to press the accelerator: 1. Place the heel of your right foot on the floor of the driver's compartment as a pivot point; 2. Gently press the accelerator pedal with the ball of your foot, using the flexion and extension of the ankle joint to press down or release; 3. When releasing the accelerator pedal, apply force gently to achieve a light press and slow release. The accelerator is part of the car's fuel supply system, and its function is to control the opening of the engine throttle by adjusting the amount of pedal pressure, thereby regulating the air intake and engine speed. Precautions for pressing the accelerator: 1. Press and release the accelerator pedal gently to achieve a light press and slow release; 2. Coordinate the release of the clutch closely with pressing the accelerator for swift action; 3. Choose the appropriate gear to ensure the engine operates at medium speed and larger throttle opening most of the time to save fuel; 4. Before the car stops or the engine shuts down, release the accelerator pedal first and avoid revving the engine abruptly.

18

4

Share

What Causes Engine Oil in the Radiator?

Possible reasons for engine oil in the radiator include: 1. Cylinder liner damage. If cracks appear in the cylinder liner, under high pressure, engine oil can seep through these gaps directly into the car's radiator. 2. Radiator damage. The engine oil cooler or transmission cooler may be damaged. 3. Cylinder head gasket damage. If there is engine oil in the radiator and the high-temperature warning light is on, it indicates a damaged cylinder head gasket. Solutions for engine oil in the radiator: 1. Disconnect the overflow tank and turn off the heater. 2. Start the vehicle and let it idle until the water temperature rises. Then, flush the radiator opening with water until no significant oil traces remain before stopping. 3. Turn off the engine, open the radiator drain valve, and once water starts flowing out, start the engine again. Continue adding water to the radiator opening to allow circulation. After 5 minutes, turn off the engine and stop adding water. Wait until all water has drained from the radiator, then close the drain valve and refill with water. 4. Start the vehicle without covering the radiator cap. After it heats up, check the radiator opening for any oil traces. If none are present, the method is effective. 5. Reconnect the overflow tank and replace the coolant as needed.

3

0

Share

Where to Use Turn Signals in Subject 2 Driving Test?

There are 6 instances where turn signals are required in Subject 2: When starting the vehicle, turn on the left turn signal; When starting on a slope, turn on the left turn signal; During parallel parking, turn on the right turn signal when pulling over to park, stopping 30 cm from the curb before reversing; Before shifting into reverse during parallel parking, turn on the left turn signal, as the steering wheel will be turned fully right during reversing, causing the front of the car to move left; Before exiting the parking space during parallel parking, shift into drive and turn on the left turn signal, turning it off promptly after exiting; When entering a sharp turn (90-degree turn), turn on the left turn signal and turn it off promptly after completing the turn. Penalties for incorrect turn signal usage are as follows: Failing to use or incorrectly using turn signals before starting, turning, changing lanes, overtaking, or parking results in a 10-point deduction. Using turn signals for less than 3 seconds before starting, turning, changing lanes, overtaking, or parking results in a 10-point deduction. Subject 2 is scored out of 100 points, with failing, 20-point, 10-point, and 5-point deduction criteria. Passing requires: ① Scoring at least 90 points for large passenger vehicles, trailers, city buses, medium passenger vehicles, or large trucks; ② Scoring at least 80 points for other vehicle types. For small vehicles (C1, C2), the test includes five mandatory items: reversing into a parking space, parallel parking, stopping and starting on a slope (removed for C2), sharp turns (90-degree turns), and S-curves (some regions include a sixth item: highway toll collection). For large vehicles (A1, A2, A3, B1, B2), the test includes: pole test, stopping and starting on a slope, parallel parking, single-plank bridge, S-curves, sharp turns, narrow gate passage, continuous obstacle course, bumpy road driving, narrow road U-turns, and simulations for highways, mountainous curves, tunnels, rain/fog, slippery roads, and emergency handling.

9

4

Share

Why Does the Car Engine Shake When Starting?

Car engine shaking during startup can be caused by: 1. Dirty throttle body; 2. Faulty spark plugs; 3. Non-functioning engine cylinders; 4. Aging rubber components in the engine mounts and transmission mounts. The car engine is the device that provides power to the vehicle, determining its power performance, fuel economy, stability, and environmental friendliness. Car engines are categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrid motors. Among these, both gasoline and diesel engines belong to reciprocating piston-type internal combustion engines, converting the chemical energy of fuel into the mechanical energy of piston motion to deliver power output.

3

4

Share

How to fill in the validity period of an electronic driver's license?

Where is the rearview mirror heating for the Lynk & Co 03 located?

Does replacing a car radiator make it an accident vehicle?

What is the correct way to press the accelerator?

What Causes Engine Oil in the Radiator?

Where to Use Turn Signals in Subject 2 Driving Test?

Why Does the Car Engine Shake When Starting?

What is the lifespan of an Aisin 6AT transmission?

Does mixing 98 octane and 95 octane gasoline have any impact?

What is the purpose of using a tensioner pulley for the drive belt?

How to match the ignition lock after replacement for Great Wall Haval H6?