How to eliminate the small wrench fault light on Refine S3?

1 Answers
VonReagan
07/28/25 6:03pm
Methods to eliminate the small wrench fault light on Refine S3: 1. Turn off the ignition switch; 2. Press and hold the adjustment rod at the lower right of the instrument panel without releasing it; 3. Turn on the ignition switch and rotate it to the "ON" position; 4. After approximately 5 seconds of the ignition switch being turned on, the small wrench fault light will go out, and then you can release the adjustment rod. The Refine S3 is a new urban compact SUV produced by Jianghuai Automobile, featuring energy-saving and environmentally friendly characteristics, sensitive handling, and intelligent technology. In terms of body dimensions, the Refine S3 measures 4325mm in length, 1765mm in width, and 1625mm in height, with a wheelbase of 2560mm.
Was this review help?
5
4
Share
More Forum Discussions

Where is the electronic water pump located on the Audi A6L?

The electronic water pump of the Audi A6L is located below the intake manifold. Introduction to automotive water pumps: An automotive water pump is a micro self-priming pump used for water circulation, cooling, or vehicle water supply systems. The circular motion of the motor drives the diaphragm inside the pump to perform reciprocating motion through mechanical devices, thereby compressing and stretching the air in the pump chamber. Features of automotive water pumps: Automotive water pumps generally have a self-priming function. Self-priming means that when the suction pipe of the pump contains air, the negative pressure formed during the operation of the pump is used to push water below the suction port up under atmospheric pressure, and then discharge it from the outlet of the pump.
1
5
Share

Does adding snow chains to tires increase or decrease friction?

Adding snow chains to tires increases friction by enhancing the coefficient of friction. Snow chains: Typically made of steel or rubber chains, they serve an anti-slip function. Based on structure, snow chains can be categorized into two types: one is the pre-formed cover type, and the other consists of several separate chains installed in a cross pattern, which is simpler and cheaper but less convenient to install than the former. The primary consideration when purchasing snow chains is safety first: they are meant to prevent slipping and ensure safety. Choosing improperly can not only be unsafe but also increase potential hazards. So-called 'nylon' materials are actually a type of plastic. In extreme cold and very low temperatures, they are prone to breakage, introducing unsafe factors to driving.
11
0
Share

Can You Turn Right on a Yellow Light?

Generally, you can proceed unless it's a new-style red right-turn arrow signal or any of the old-style red-green-yellow circular signals is lit. There are three situations where you cannot turn right: When there is a sign stating "No right turn on red": because the yellow light is on without crossing the stop line, missing the opportunity to proceed. When there is an oncoming left-turning vehicle from the opposite direction: because left turns have priority over right turns when both vehicles are turning. When there is a straight-moving vehicle in the left lane: because straight-moving vehicles have priority over turning vehicles. In simpler terms, you can usually proceed, but if the intersection has a right-turn traffic light or signs indicating restrictions, vehicles that have not passed the stop line cannot proceed.
14
1
Share

Where is the engine number of the old Besturn B70?

The engine number of the Besturn B70 is located at the bottom of the engine, and you need to remove the bottom protective cover to see it. It is usually a combination of 7 to 8 digits and letters. In addition to the above method, the engine number can also be checked in the following 4 ways: The vehicle's driving license will have the engine number printed, usually located on the second-to-last line; The motor vehicle registration certificate will state the engine number; The car purchase invoice will state the engine number; The vehicle purchase tax payment certificate will state the engine number. It should be noted that the engine number is not the same as the engine model. The engine model refers to the specifications and size of the engine within the manufacturer, and engine models can be the same. The engine number refers to the production number of the engine, and each engine can only use one engine number, with each engine's number being unique.
12
0
Share

What's the Difference Between Full-Cover and Half-Cover Car Seat Covers?

The differences are as follows: Full-Cover Type: Advantages: Provides complete protection for the seats, especially for leather seats, offering excellent protection. Disadvantages: As mentioned in previous articles, seat covers are limited in material choices, typically being either fabric or leather. Therefore, there are fewer options in terms of style and design, making the selection space relatively narrow. Another drawback is that installing seat covers is more challenging than installing seat cushions. Half-Cover Type: Advantages: Offers diversity in materials and styles. Choosing a more suitable car seat cushion for your car's style is a very simple task. Moreover, in different seasons, it's easy to replace the seat cushion with materials suitable for that season. Disadvantages: The seats are not fully wrapped. If you frequently carry pets or mischievous children in the car, the seats can easily get damaged in areas that are not covered.
19
1
Share

What phenomena are prone to occur when the rear wheels lock up?

Car will be unable to drive normally. Specific reasons: If the left rear wheel of the car locks up, it is due to excessive wear of the vehicle's brake pads. This causes the brake caliper in the braking system to extend too far and fail to retract naturally, leading to jamming. At this point, the vehicle's brake pads are in a locked state, naturally causing the wheel to lock. Simply replacing the vehicle's brake pads will resolve the issue. Main advantages: The master cylinder rubber cup may become stuck and fail to return to its original position, causing the rear wheels to lock. This could be due to water or other impurities entering the braking system, or failure to clean the system thoroughly before switching to a different brand of brake fluid, causing the master cylinder rubber cup to swell and resulting in the rear wheels of the car locking up.
11
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.