···
Log in / Register

How to eliminate the flashing AFS light on an old Camry?

4 Answers
McAndrew
07/23/25 6:12pm

AFS OFF light indicates that the headlight's adaptive front-lighting system (AFS) is turned off. Press the switch button located above the brake pedal to activate the intelligent adaptive front-lighting system. Inspect the AFS module, use a decoder to match and set the system, and clear the fault code to eliminate the AFS warning light. Disconnect the headlight power supply, ensure the vehicle's power is off, then open the engine hood, locate the battery's negative terminal, disconnect and reconnect it.

Was this review help?
6
5
Share
McCollin
08/10/25 1:49pm

When the AFS light on my old Camry flashes, I looked it up and found that it indicates a fault in the adaptive headlight system. Focus on checking three areas: whether the steering module in the headlight assembly has poor contact, if the wiring of the rear axle vehicle height sensor is aged or broken, and also inspect the connection of the steering wheel angle sensor. Last time, I discovered that the sensor connector was corroded—after cleaning the connector and resetting the system with a diagnostic tool, it worked fine. If you can't fix it yourself, spending some money to have a repair shop connect a computer to read the fault codes is the most hassle-free solution. Don't push through it; the flashing light means the illumination angle during turns might be uncontrolled, which is quite dangerous when driving at night.

Was this review help?
20
2
Share
Expand All
Destiny
09/22/25 8:30am

The AFS light flashing issue with the Camry is quite common, I've encountered it several times. First, open the engine hood to check the wiring harness near the headlights. On older cars, the rubber insulation tends to deteriorate, making it prone to peeling and short circuits. Then, get under the car to inspect the height sensor. The metal plate on it can easily get clogged with mud, causing signal errors. A simple fix is to remove the sensor and clean it with WD40. Last time at the repair shop, I saw the mechanic replace the sensor and then use professional equipment to recalibrate and reset it. If you're handy, you can buy an OBD scanner yourself—just over a hundred bucks, and you can connect it to your phone to clear the fault codes. When washing your car, pay attention to rinsing the undercarriage, as excessive mud and sand can easily trigger this problem.

Was this review help?
3
1
Share
Expand All
KathrynAnn
11/06/25 2:50am

The flashing AFS light on older Toyotas is usually a sensor issue. Here's how I fixed it myself: Turn off the engine, remove the key, wait 5 minutes, then restart to let the system self-check. If the light still flashes, inspect the AFS-related fuses in the fuse box. Next, turn the steering wheel fully left and right once each to reset the steering sensor. If that doesn't work, check the small square sensor on the rear suspension - it's prone to moisture errors during rainy seasons. I recommend avoiding tinkering in humid weather; wait for a sunny day for safer disassembly. Don't randomly unplug connectors as wiring in older cars is quite fragile.

Was this review help?
8
1
Share
Expand All
More Forum Discussions

How Many Kilometers Can a New Energy Vehicle Run?

Generally, new energy vehicles can run between 100-600KM. Below is relevant information about new energy vehicles: 1. Definition: New energy vehicles refer to vehicles that utilize unconventional vehicle fuels as power sources (or use conventional vehicle fuels with new types of onboard power devices), integrating advanced technologies in vehicle power control and driving, resulting in vehicles with advanced technical principles, new technologies, and new structures. 2. Classification: New energy vehicles include four main types: Hybrid Electric Vehicles (HEV), Battery Electric Vehicles (BEV, including solar-powered vehicles), Fuel Cell Electric Vehicles (FCEV), and other new energy vehicles (such as those using supercapacitors, flywheels, and other high-efficiency energy storage devices).
20
0
Share

What is the meaning of the insured vehicle and the third-party vehicle?

The insured vehicle is the one covered by the insurance policy. The third-party vehicle is the one that was hit in an accident. Below are some relevant introductions about driving a car: 1. Precautions: Do not drink alcohol before driving. It is common knowledge that driving under the influence is prohibited. Avoid wearing headphones while driving as they can muffle external sounds and interfere with your judgment. Ensure your car is regularly maintained before hitting the road, and always check the vehicle's condition before each drive. 2. Good habits: It's advisable to walk around the car and inspect its exterior and tires for any abnormalities before driving. Once inside, first adjust the steering wheel position, then the seat. Ensure your driving posture is properly set before starting the engine and shifting into gear to begin your journey.
5
3
Share

Is it advisable to buy a car right after getting a driver's license?

It is possible to buy a car, but it is generally recommended to start with a cheaper car or a used one for practice. Here are some driving tips for beginners: 1. Pay attention to speed: Unless on a highway, it's best for beginners to maintain a steady speed of around 60 km/h for better control. 2. Frequently check the rearview mirrors: Rearview mirrors help observe road conditions behind and to the sides of the vehicle, especially when changing lanes, reversing, or overtaking. 3. Maintain a safe distance: Keeping a proper distance from the car ahead is crucial. If another car cuts in, slow down appropriately to yield. 4. Use lights correctly: Avoid randomly turning on hazard lights. Turn on the parking lights at dusk, and only use fog lights in poor visibility conditions like heavy fog.
19
2
Share

How many days does it take to check for speeding violations on the highway?

Under normal circumstances, violations on the highway will be notified and can be checked online within two to three days. Here are some precautions to avoid highway violations: 1. Comply with: the traffic regulations of the highway. 2. Pay attention to: observing roadside traffic signs and markings on the ground, and promptly understand the location information of exits, entrances, or service facilities. 3. When entering or exiting the highway: use turn signals correctly, and do not hinder the normal flow of vehicles when changing lanes. 4. While driving: maintain focus and avoid fatigued driving. 5. During travel: keep a safe distance from the vehicle in front.
4
3
Share

Diesel or Gasoline Cars for Plateau Use?

Diesel cars are recommended for plateau areas. Here are some comparisons between diesel and gasoline vehicles: 1. Fuel Efficiency: Diesel cars are more fuel-efficient than gasoline cars due to their engine technology. The compression-ignition diesel engine has a higher energy conversion ratio than spark-ignition gasoline engines, consuming only 45%-60% of the energy used by gasoline engines. 2. Power Performance: Diesel engines provide greater low-speed torque compared to gasoline engines. With the same displacement, diesel vehicles deliver more powerful acceleration and hill-climbing performance. Diesel fuel is less volatile than gasoline, has higher power output, and a higher ignition point. Small diesel engines are about one-third more fuel-efficient than gasoline engines. The compression-ignition diesel engine achieves higher energy conversion efficiency, consuming only 45%-60% of the energy required by gasoline engines.
9
0
Share

Is Replacing Engine Connecting Rods a Serious Issue?

Not serious. As long as the replaced parts are normal components and the assembly is done properly, there will be no impact on the vehicle. Below are specific details about engine connecting rods: 1. Principle: The working principle of connecting rods involves using hinges and sliding mechanisms to interconnect components, achieving motion transformation and power transmission. Connecting rods can fulfill various motion trajectory requirements and enable transformations between different motion forms. Planar linkage mechanisms are widely used in various machinery, instruments, and electromechanical products. 2. Composition: The connecting rod body consists of three parts: the small end connects to the piston pin; the big end connects to the crankshaft; and the rod section between the small end and big end is called the connecting rod shank.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.