How to Drive When Encountering Slow-Moving Vehicles Ahead?

1 Answers
VonCali
07/25/25 8:00am
When all vehicles ahead are moving slowly, it is necessary to maintain a safe following distance. Below are some precautions regarding car driving: 1. Cold Engine Warm-up: Proper warm-up helps form an "oil film" between engine components, reducing wear. 2. Timely Gear Shifting: When driving a manual transmission vehicle during the break-in period, shift gears promptly and appropriately to avoid incorrect behaviors like high gear with low RPM or low gear with high RPM, and do not use a single gear for extended periods. 3. Timely Maintenance: Simply follow the manufacturer's recommendations in the vehicle manual, and perform timely inspections and maintenance after reaching certain mileage or time intervals, including oil and oil filter changes, along with a comprehensive check of the chassis system. 4. Avoid Emergency Braking: Emergency braking not only shocks the braking system during the break-in period but also increases the impact load on the vehicle's chassis and engine.
Was this review help?
4
5
Share
More Forum Discussions

What documents are required for a driver's license medical examination at the hospital?

Required documents include the original ID card and one photocopy. Here are the relevant details: Introduction: Drivers undergoing the medical examination must present their own documents: driver's license (both original and copy). They must carefully and truthfully fill out the driver's review and license renewal application form, attaching one recent one-inch passport-sized photo. Regulations: If a motor vehicle driver's household registration is transferred out of the jurisdiction of the original vehicle management office, they must apply for a license renewal at the vehicle management office in the new jurisdiction. If a motor vehicle driver resides outside the jurisdiction of the issuing vehicle management office, they may apply for a license renewal at the vehicle management office in their place of residence. When applying, the applicant must complete the 'Motor Vehicle Driver's License Application Form' as required and submit the driver's identity proof as well as the motor vehicle driver's license.
18
3
Share

Why is the car locked and unable to start?

When a car is locked and unable to start, it indicates the vehicle is equipped with an engine electronic anti-theft system, also known as a transponder-based immobilizer. Its fundamental principle is to lock the car's engine, electrical circuits, and fuel system, preventing the vehicle from starting without a chipped key. A locked car anti-theft system is a common malfunction of vehicle anti-theft devices. Relevant explanations are as follows: 1. The car has an engine electronic anti-theft system, which only allows the vehicle to start when the chip inside the key matches the code in the anti-theft system. 2. The spare key does not contain a chip, hence it cannot start the car. The spare key can only be used to unlock the door when the original key is lost.
15
4
Share

What Happens When the Car Fan Control Module Fails?

Turn on the air conditioning to see if it spins. If it doesn't, the fan motor is faulty; if it does, the temperature controller is faulty. Below are the specific control principles of car fans: 1. Thermoswitch "Sole" Control: The high and low speeds of the car fan are "solely" controlled by the thermoswitch. This switch has two gears and is installed on the radiator to detect water temperature. 2. Radiator Control: The car fan is installed behind the radiator and pulls air from the front of the radiator when turned on. However, some models have fans installed in front of the radiator, blowing air toward the radiator when turned on. 3. Engine-Driven: The electric fan does not rotate when the engine is cold but starts spinning as the temperature rises, driven by an electric motor. 4. Fan Control Device: To reduce engine power loss and save fuel, mechanical fans often use a fan control device to engage or disengage the cooling fan from the drive pulley.
19
1
Share

What is the method to prevent stalling on a hill start?

The method to prevent stalling on a hill start is: 1. After engaging first gear, first apply throttle by pressing the accelerator until the tachometer reads 1500 to 2000 RPM, then hold your right foot steady; 2. Slowly release the clutch to the bite point, then press it back slightly - meaning just before reaching the actual bite point - and hold your left foot steady while quickly releasing the handbrake; 3. If you notice the car starting to roll backward while releasing the handbrake, gently release the clutch further with your left foot while maintaining throttle between 1500 to 2000 RPM. Additional note: When performing a hill start, remember not to lift the clutch while pressing the accelerator, and lift the clutch slowly - doing it too quickly may cause stalling.
1
5
Share

Why Does the Brake Make Noise When Braking?

The reason for brake noise is worn brake pads, which need to be replaced promptly. Relevant details are as follows: 1. Brake pads are consumables that gradually wear thinner during vehicle use. When the friction layer is nearly depleted, an alarm device, namely the brake pad wear indicator, located at the edge of the brake pad will come into contact with the brake disc, producing a sharp metallic friction sound as a warning to the driver that the brake pads should be replaced. 2. Brake fluid is recommended to be replaced every 2 years. Brake fluid has certain corrosive properties and strong water absorption. Nowadays, service stations are equipped with specialized tools to measure the water content in brake fluid, allowing for a test to determine if replacement is necessary. Brake fluid must be replaced regularly according to the maintenance schedule, and it is advisable to follow the manufacturer's recommended maintenance intervals.
6
5
Share

Will the car door break if slammed twice?

The car door generally won't break if slammed twice. Here's the relevant information: 1. Car door: The car door provides access for the driver and passengers, isolates external interference, reduces side impacts to some extent, and protects occupants. The aesthetics of the car are also related to the design of the door. The quality of the car door is mainly reflected in its anti-collision performance, sealing performance, ease of opening and closing, and other functional indicators. Anti-collision performance is particularly important because in the event of a side impact, the buffer distance is very short, making it easy to injure the occupants. 2. Car door maintenance: Pay attention to the door stopper when opening and closing the door, be careful with keys and other objects that may scratch the door, avoid excessive force when closing the door, and protect the door's sealing rubber strip.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.