How to Drive the Lavida Tiptronic Manual Mode?

What does the white dashed line in the middle of the road indicate?

Roads in the white dashed line refers to the center line that can be crossed in the same direction lane. Generally, road markings are divided into white and yellow lines, which are further categorized into solid and dashed lines. Here is an introduction to the center line: 1. Dashed line: When driving on the road, if there is a dashed line in the center of the road, it indicates that vehicles can cross the road. 2. Solid line: If it is a solid line, vehicles are not allowed to cross. Road markings are divided into white and yellow lines, which are further categorized into solid and dashed lines. Yellow lines indicate lanes that can be crossed in the opposite direction; the boundary line for one-way traffic lanes is a solid line.

19

4

Share

What Happens If You Pour Water into a Car's Exhaust Pipe?

When water enters a car's exhaust pipe, there are no obvious symptoms, and the accumulated water will be expelled due to the engine's operation. Here are the effects of water entering the exhaust pipe: 1. Water in the exhaust pipe, but the engine is not affected: Water in the exhaust pipe can lead to serious consequences such as water entering the engine. If only the exhaust pipe has water, it is essential to remove the water as soon as possible to prevent impurities from clogging the catalytic converter or damaging the oxygen sensor. To drain the water, simply increase the throttle to expel the water through the exhaust. 2. Engine stalling due to a blocked exhaust pipe: Water in the exhaust pipe may cause blockage, leading to poor exhaust flow and engine stalling. However, in this case, the engine may not necessarily take in water; it is just what is commonly referred to as 'choked out.' There is no need to worry in such situations. Once the water drains out, the car can be started again.

12

1

Share

Does the Fuel Pump Automatically Shut Off When the Tank is Full?

When the fuel tank is full, the pump will automatically shut off. Gas stations commonly use self-sealing fuel nozzles that automatically trip when the tank is full. These nozzles utilize a special structural design in the reflux valve assembly to create negative pressure within the pressure-sensing system. Precautions for refueling include: 1. Refuel in the morning or evening to avoid direct sunlight at noon; 2. Add fresh fuel before long trips; 3. Do not exceed the tank's maximum capacity; 4. Avoid using electronic devices; 5. No smoking; 6. Turn off the engine and power when parked. Solutions for misfueling: 1. If higher-grade fuel is accidentally replaced with lower-grade, short-term use won't harm the engine; 2. If gasoline is mistakenly added as diesel, contact a repair shop immediately to clean the fuel tank and lines, and conduct a thorough engine inspection—do not start the engine to avoid damage; 3. If diesel is added as gasoline, replace the fuel immediately.

16

2

Share

Which BYD S6 model uses a Mitsubishi engine?

The BYD S6 2012 model uses a Mitsubishi engine, which is produced in Shenzhen. The engine model used in the BYD S6 is the Mitsubishi 4G69, with a maximum horsepower of 160 HP, a maximum power of 118 KW, a maximum power speed of 5000-6000 rpm, and a maximum torque of 215 Nm. Daily maintenance methods for the BYD S6 engine include: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to the mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level; When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, it may rupture the filter element or open the bypass valve, allowing dirty oil to return to the lubrication area, accelerating engine wear and increasing internal contamination; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

10

1

Share

What does the stop yield line mean?

Stop yield is generally set at intersections with poor visibility and no traffic lights, meaning that vehicles must stop and observe before proceeding. 1. Sign: The stop yield line consists of two white-painted lines. It indicates that vehicles must stop beyond the stop line to look out and confirm safety before being allowed to proceed. The stop line is the most common, this line is a solid white line, indicating the position where vehicles wait for the signal to proceed, and must not cross or press this line. 2. Meaning: "Stop yield" is a traffic prohibition sign, an octagon with "STOP" in the middle, meaning to stop at the intersection at the stop line to observe before proceeding. The stop yield line consists of two white-painted lines. It indicates that vehicles must stop beyond the stop line to look out and confirm safety before being allowed to proceed. 3. Location setting: Stop yield signs are set in the following situations: 1. At intersections of branch roads intersecting with main roads with heavy traffic; 2. At unattended railway crossings; 3. Other places where it is necessary to set.

11

4

Share

How to switch from D gear to S gear in an automatic transmission?

To switch from D gear to S gear in an automatic transmission, simply shift the gear lever from D to S while driving normally; there is no need to press the brake or come to a complete stop. D gear is the drive mode, where the vehicle prioritizes comfort and fuel efficiency. S gear is the sport mode, which focuses on high performance. When shifted into S gear, the transmission delays upshifting to allow the engine to deliver greater power. The correct way to use an automatic transmission is as follows: 1. Start the vehicle in P or N gear. To shift out of P gear, press the brake, turn on the ignition, and then shift to N gear. After starting the engine, shift to D gear to move forward. 2. When switching between N, D, and L gears, there is no need to press the shift button. However, when shifting from L gear to lower restricted gears, press the shift button. Shifting from lower to higher gears does not require pressing the shift button. 3. Do not shift into N gear while driving to coast. 4. Do not push into P gear while driving. 5. After driving, you must turn off the engine and shift into P gear before removing the key.

11

1

Share

How to Drive the Lavida Tiptronic Manual Mode?

What does the white dashed line in the middle of the road indicate?

What Happens If You Pour Water into a Car's Exhaust Pipe?

Does the Fuel Pump Automatically Shut Off When the Tank is Full?

Which BYD S6 model uses a Mitsubishi engine?

What does the stop yield line mean?

How to switch from D gear to S gear in an automatic transmission?

What is the problem with the difficult starting of Changan Honor engine?

What are the steps to replace wiper blades?

Where is the crankshaft sensor located on the Wuling Hongguang?

How to adjust the ambient lighting in the new Sagitar?