How to Drive Safely After Entering the Highway Lane?

1 Answers
LeGabriella
07/23/25 11:12pm
After entering the highway lane, the driving methods are as follows: Lane Discipline: When driving on a highway, vehicles must strictly adhere to the designated lanes. On a two-lane highway in the same direction, vehicles traveling below 100 km/h should stay in the right lane. On a three-lane highway, the minimum speed for the rightmost lane is 60 km/h. Vehicles traveling above 90 km/h should use the middle lane, while those exceeding 110 km/h should drive in the leftmost lane. Speed Control: Driving at excessively high speeds on the highway is not advisable, as it significantly increases the risk of accidents. However, driving too slowly is also unsafe, as it creates a large speed differential with other vehicles, leading to frequent overtaking situations. Therefore, drivers must strictly comply with the maximum and minimum speed limits specified in traffic regulations.
Was this review help?
13
4
Share
More Forum Discussions

How to adjust the handbrake of Buick Excelle?

Remove the bottom of the small storage box, then remove the gear shift dust cover, the large frame of the audio system, and the side panels of the central console. You will see two screws. Remove the seven small sockets, move the seat forward, and then remove the two screws at the back. Finally, remove the rear cigarette lighter panel and the handbrake dust cover to take off the entire armrest. To adjust the handbrake, loosen the two 20mm spline screws behind the handbrake lever and repeatedly pull and release the handbrake.
7
1
Share

What causes the cruise control system failure in BMW 3 Series?

The cruise control system (CRUISE CONTROL SYSTEM), abbreviated as CCS, is also known as speed control device or autonomous driving system. Reasons for cruise control system failure include: Internal control unit or circuit failure: For instance, the ACC control unit needs to transmit signals to both ICM and LDM units. If these units themselves have issues or there are connection faults between them, signals cannot be properly transmitted. Wheel speed sensor: If you receive "cruise control system failure" warnings along with alerts related to DSC, ABS, or RPA systems, it's highly likely caused by malfunctioning wheel speed sensors.
6
5
Share

Which brand does the Bestune T77 belong to?

The Bestune T77 is the first model in the new 'T' series product lineup of Bestune, which belongs to the China FAW Group. The dimensions of the Bestune T77 are 4525mm in length, 1845mm in width, and 1615mm in height, with a wheelbase of 2700mm. This vehicle is equipped with a 1.2-liter turbocharged engine across the entire series, delivering a maximum power of 105 kW and a maximum torque of 204 Nm. The engine reaches its maximum power at 5500 rpm and its maximum torque between 1600 to 4200 rpm. It is paired with either a 6-speed manual transmission or a 7-speed dual-clutch transmission.
17
0
Share

How to Start a Buick Car?

The one-button start for Buick is located at the lower right corner of the dashboard. With the key fob in possession, the owner can start the vehicle directly. To start the car, press the brake pedal and then press the start button. If you only want to turn on the ignition without starting the engine, you can press the start button without stepping on the brake pedal. To park, follow these steps: stop the car, press the brake pedal, shift to N gear, release the brake, engage the handbrake, turn off the engine, and shift to P gear.
4
2
Share

What type of transmission is used in the Besturn B90?

The Besturn B90 is equipped with a 6-speed automatic transmission (6AT) across all variants. The AT transmission, also known as a torque converter transmission, connects to the engine via a hydraulic torque converter. Inside the AT transmission, planetary gears are employed to achieve gear shifting and torque variation. This type of transmission offers smooth gear shifts and excellent reliability and durability. The Besturn B90 serves as the premium flagship model under the Besturn brand, with body dimensions of 4860mm in length, 1812mm in width, and 1472mm in height, along with a wheelbase of 2780mm. In terms of exterior design, the newly designed grille enhances the three-dimensional effect and detailed surface treatment, elevating the vehicle's technological appeal while adding a more dynamic touch.
2
1
Share

How to Operate the Gear Shift in a Buick?

When entering this gear, the transmission locking mechanism engages, so the vehicle must come to a complete stop before shifting into it. Engage the reverse gear when the vehicle needs to reverse, noting that the vehicle must first come to a complete stop before shifting into reverse. The neutral position is located after the reverse gear. When shifted into neutral, the vehicle's engine power is not transmitted, typically used for short-term parking. Used when the vehicle is moving forward, the drive gear is located below the neutral position. Manual mode requires the driver to manually shift gears, usually pushing up to shift up one gear and pushing down to shift down one gear. Manual mode can enhance the driving experience.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.