How to drive a BMW X3?

1 Answers
GrahamLynn
07/29/25 11:05pm
Driving method for BMW X3: Press the ignition switch to start the engine, use the electronic gear lever to shift gears and start driving. Manual mode can be engaged using the paddle shifters on the steering wheel. The BMW X3 is a mid-size SUV launched by BMW Brilliance, with dimensions of 4717mm in length, 1891mm in width, and 1689mm in height, and a wheelbase of 2864mm. It is equipped with a 2.0T turbocharged engine, delivering a maximum power of 135kw, paired with an 8-speed automatic transmission. The BMW X3 combines the distinctive proportions of a Sports Utility Vehicle with classic and innovative design, introducing the new SUV concept of a Sports Activity Vehicle, and is equipped with BMW's patented xDrive intelligent all-wheel-drive system.
Was this review help?
18
5
Share
More Forum Discussions

How to replace the battery of Zotye T700 remote key?

The method to replace the battery of Zotye T700 remote key is: 1. Use a small flat-head screwdriver to pry open the back cover of the key and remove it. After opening the back cover, you can see the old battery; 2. Remove the old battery and install the new battery into the slot. When installing the battery, pay attention to the positive pole facing downward; 3. Reinstall the back cover of the key according to the original steps. Taking the 2018 Zotye T700 as an example, its body structure is a five-door five-seat SUV, with body dimensions of length 4748mm, width 1933mm, height 1697mm, a wheelbase of 2850mm, a fuel tank capacity of 64L, and a curb weight of 1787kg.
3
1
Share

How to Replace the Air Conditioning Filter in Changan CS55

The method to replace the air conditioning filter in Changan CS55: 1. There is a black plastic panel above the passenger side footwell with two retractable clips; remove the panel by releasing these clips. 2. Disconnect the negative terminal of the battery, then remove the body control module and its mounting bracket. 3. Remove the panel on the left side of the passenger footwell, which is secured with four screws. If the filter is very dirty, clean it by blowing compressed air from the opposite side. Hold the air gun about 5cm away from the filter and blow at 500kPa pressure for approximately 2 minutes. The air conditioning filter tends to accumulate a lot of dust. Use a blower or high-pressure air to remove the loose dust. Do not wash it with water, as this can easily damage the filter.
13
4
Share

Why is the car front fog light not working?

Car front fog light not working reasons are: 1. The bulb current is too large, causing the switch to overheat; 2. Poor contact of the ground wire; 3. The plug is contaminated with mud or water. Car fog lights should be turned on when driving at night without street lights, poor lighting, or encountering low visibility conditions such as fog, rain, snow, dust, or hail. The methods to turn them on are: 1. Rotate the light control lever located below the left side of the steering wheel; 2. Press the fog light button near the instrument panel. Precautions for using car fog lights are: 1. When visibility is below 100 meters, fog lights must be turned on and speed should be reduced; 2. When visibility is below 30 meters, turn on the fog lights, pull over, and activate the hazard warning lights; 3. In rainy, foggy, snowy, or dusty weather, turn on the fog lights and reduce speed.
16
0
Share

How to Replace Brake Fluid for Focus?

Steps to replace brake fluid for Focus: 1. Turn the ignition switch to the OFF position and disconnect the ABS actuator and electrical unit harness connector or the negative terminal of the battery; 2. Loosen the fixing screws of the tire, then lift the vehicle and completely remove the tire; 3. Insert the ethylene tube into the brake caliper bleed valve, press the brake pedal and release the bleed valve to gradually drain the brake fluid; 4. When filling the brake fluid, ensure there are no foreign objects in the reservoir, then slowly pour it in. Note that different types and brands of brake fluid should not be mixed. For brake systems with special requirements, a specific brand of brake fluid should be used. Since different brands and types of brake fluid have different formulations, mixing them can cause a decline in the performance indicators of the brake fluid.
4
3
Share

What is the meaning of the tire pressure marking on car tires?

The tire pressure marking on motor vehicle tires indicates the maximum tire pressure limit that the tire should not exceed, for example, usually not exceeding 340 kPa, which is equivalent to 3.4 bar. Generally, the tire pressure marking on motor vehicle tires is located on the sidewall of the tire. Below is an introduction to tire pressure: Normal tire pressure reference standards: According to the regulations and requirements of the international GBT2978-2008 standard, the standard tire pressure is approximately 2.4-2.5 bar, while reinforced tires are around 2.8-2.9 bar. In winter, it is advisable to slightly increase the tire pressure by about 0.2 bar based on the standard tire pressure, whereas in summer, the tire pressure can generally be set slightly lower than the standard by about 0.1 bar to prevent blowouts due to high temperatures. When the vehicle is unloaded or half-loaded, adjust the tire pressure to the lower limit of the standard; when fully loaded, adjust it to the upper limit. On roads with significant bumps, it is appropriate to reduce the tire pressure by 0.1-0.2 bar from the standard. Hazards of over-inflated tires: Over-inflation reduces the tire's friction and grip, prolonging the braking effect. Additionally, the tire becomes harder, decreasing ride comfort and causing more significant body vibrations, indirectly affecting the lifespan of other components such as the suspension. Under-inflated tires are more prone to blowouts: Tires are more likely to blow out when under-inflated. This is because low tire pressure causes significant deformation of the tire sidewall, and during operation, the sidewall is continuously stretched and compressed. Since the sidewall is relatively weak, it is easily damaged.
15
5
Share

How to Replace the Rear Brake Pads on the Envision?

To replace the rear brake pads on the Envision, follow these steps: 1. Remove the tire to expose the brake drum; 2. Use a hammer to tap the brake drum until it loosens and can be removed; 3. Take off the old rear brake pads and install the new ones. Brake pads, also known as brake linings, are crucial safety components in a car's braking system. The effectiveness of the braking largely depends on the condition of the brake pads. The Envision measures 4694mm in length, 1839mm in width, and 1686mm in height, with a wheelbase of 2750mm. It is a 5-door, 5-seater SUV equipped with a 7-speed dual-clutch transmission.
7
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.