How to Dispose of Replaced Tires?

What are the signs of a car tire blowout?

Signs of a car tire blowout include: 1. Small bubble-like protrusions appearing on the tire; 2. Excessive tire wear leading to shallow tread patterns or visible tread wear indicators; 3. Abnormal internal tire pressure; 4. Cracks appearing on the tire sidewall. The functions of a tire are to support the entire weight of the vehicle, transmit traction and braking torque, prevent vibration and damage to vehicle components, and ensure driving safety. The process for replacing a tire: 1. Loosen the screws; 2. Lift the vehicle with a jack; 3. Remove the screws securing the wheel (counterclockwise to loosen, clockwise to tighten); 4. Remove the tire; 5. Install the new wheel.

17

5

Share

How to Adjust the Headlights of Chery Fengyun 2?

The method to adjust the headlights of Chery Fengyun 2 is as follows: Locate the adjustment switch on the right side of the light switch on the center console below the steering wheel. Find a wall about 10 meters away, turn on the headlights, and then make slight adjustments up and down using the switch. Taking the 2016 Chery Fengyun 2 as an example, its body dimensions are: 4188mm in length, 1686mm in width, and 1480mm in height, with a wheelbase of 2527mm. The 2016 Chery Fengyun 2 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 109PS, a maximum power of 80kW, and a maximum torque of 140Nm, paired with a 5-speed manual transmission.

20

2

Share

What does the torque parameter in cars refer to?

Automotive torque parameter refers to the torque force of a vehicle and the moment output from the crankshaft end of the engine. Under the condition of fixed engine power, torque is inversely proportional to the engine speed—the faster the speed, the smaller the engine torque; the slower the speed, the greater the engine torque. It also reflects the vehicle's load capacity within a certain range. Like power, torque is one of the indices of a car's engine, which is reflected in the vehicle's performance, including acceleration, climbing ability, and suspension, among others. The definition of torque is: the reciprocating motion of the piston in the cylinder, with each reciprocation doing a certain amount of work, measured in Newton meters.

12

2

Share

What does it mean when the EPC light comes on during a car self-check?

The EPC indicator light can illuminate in two states: during power-on self-check and under other circumstances. The power-on self-check is an indication that the vehicle is monitoring the status of all sensors before driving. Generally, if the vehicle is not started after power-on, the light will turn off on its own after about 3 seconds. If the EPC light remains on under other circumstances or does not turn off for a long time after the vehicle is started, the possible causes include faults in the engine intake system, throttle, fuel system, engine, ECU control unit, or brake lights. The following are detailed explanations of the causes for the EPC light to illuminate under other circumstances: Engine intake system fault: The EPC light will illuminate if the engine intake is obstructed or insufficient. Throttle fault: Carbon buildup is a common issue with the throttle. Additionally, dirt on the throttle body can affect intake, causing the indicator light to come on. Fuel system fault: This includes issues such as substandard fuel, fuel deterioration, or poor fuel atomization. Engine fault: Insufficient engine pressure or problems with components like the intake valve in the powertrain can also trigger the EPC light. ECU control unit fault: Examples include interference with the vehicle's computer signals or false alarms from the computer. Brake light fault: This includes situations where the brake lights do not illuminate, the brake switch malfunctions, or there are issues with the brake circuit. Solutions for when the EPC light comes on: Troubleshoot the intake system, use fuel with the appropriate octane rating, clean the throttle, etc. Remove carbon deposits from relevant components. Re-flash the ECU data. If the EPC light comes on, the owner can first try turning off the engine and restarting it to see if the EPC light remains on. If it does not, there may be no issue, and the EPC light might have been affected temporarily. If the EPC light stays on or frequently illuminates, the vehicle should be taken to the nearest service center for professional diagnosis and repair to eliminate potential safety hazards. The full English name of EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily includes controllers and sensors related to the powertrain. When sensor data in the system is abnormal, the EPC system will take predefined actions to address the powertrain issues. The EPC indicator light typically appears in two colors: yellow and red. If the EPC light is yellow and the vehicle can still operate normally, drive slowly to a service center for inspection. If the EPC light is red, the situation is more severe, and the driver should pull over immediately and contact a professional for repairs. Continuing to drive under these conditions may damage core components or compromise driving safety.

16

2

Share

What Causes Weak Ignition When Starting a Car?

The reasons for weak ignition when starting a car are: 1. Insufficient battery power; 2. Malfunction in the ignition system; 3. Issues with the fuel supply system. The method to start a car is: 1. Insert the key, turn it to the second power position for ignition, and wait for the system self-check to complete; 2. Shift the gear lever from P to N; 3. Release the brake and start the car's engine; 4. Press the brake pedal to shift the gear lever from N to D, then release the brake and press the accelerator to start. Precautions for shifting gears in a car: 1. Do not press the accelerator pedal when shifting gears; 2. Do not immediately press the accelerator pedal hard after shifting into gear; 3. The vehicle can only be started in P or N gear; 4. The gear lever must be removed from P gear by pressing the brake; 5. Do not shift into N gear while driving to coast.

12

2

Share

What causes the car dashboard to flash and the engine not to start?

The reasons why the car dashboard flashes and the engine does not start are: 1. Low-pressure fuel line blockage, loose pipes causing oil leakage, air in the high-pressure fuel line, incorrect fuel injection timing angle; 2. Power supply failure, poor contact of the electromagnetic switch, poor contact between the starter motor commutator and brushes, clutch slippage in the starter transmission mechanism; 3. Cylinder head gasket damage causing air leakage, valves not sealing tightly leading to air leakage, piston and cylinder liner wear causing air leakage, insufficient cylinder compression pressure; 4. Air filter element clogged, insufficient air intake; 5. Low battery charge. The function of the battery is: to supply power to the starting system, ignition system, electronic fuel injection system, and car's electrical appliances during engine startup.

8

3

Share

How to Dispose of Replaced Tires?

What are the signs of a car tire blowout?

How to Adjust the Headlights of Chery Fengyun 2?

What does the torque parameter in cars refer to?

What does it mean when the EPC light comes on during a car self-check?

What Causes Weak Ignition When Starting a Car?

What causes the car dashboard to flash and the engine not to start?

Can Halogen Lights Be Replaced with LED?

How to Fix Broken License Plate Mounting Holes?

How to use the cigarette lighter in a Prado?

How to Use a Paint Thickness Gauge?