How to Display the Total Mileage on the X-Trail?

1 Answers
DominicDella
07/25/25 9:54am
To display the total mileage on the X-Trail: Turn the ignition switch to the "ON" position, and the total odometer and dual short-distance trip meters will appear on the vehicle information display. The total odometer shows the vehicle's overall mileage, while the dual short-distance trip meters display the distance of individual trips. The X-Trail is a compact SUV with a 5-door, 5-seat configuration. Its dimensions are 4675mm in length, 1820mm in width, and 1722mm in height, with a wheelbase of 2706mm. It is equipped with a 4-cylinder, 2.0-liter, 151-horsepower naturally aspirated engine, paired with a CVT transmission that simulates 7 gears. The suspension system combines MacPherson strut front suspension and multi-link rear suspension.
Was this review help?
14
4
Share
More Forum Discussions

How many liters of power steering fluid are needed for a single replacement?

Replacing power steering fluid typically requires 1 liter, but the exact amount depends on your specific vehicle model. Additionally, routine inspections should be conducted every six months, coinciding with each minor maintenance service. When to add fluid: During inspections, the decision to replace the fluid is primarily based on color changes. Normal power steering fluid is transparent with a slight reddish tint. However, if the fluid appears cloudy or blackened, replacement is necessary. The power steering fluid reservoir is usually transparent and marked with minimum and maximum level indicators. If the fluid level falls below the minimum mark, you should add the manufacturer-recommended fluid type. Replacement precautions: During replacement, avoid running the engine without fluid for extended periods as this can damage the power steering pump. Additionally, used power steering fluid should not be disposed of carelessly; it's best to store it in specialized recycling containers for professional disposal. Note that power steering fluid is highly corrosive and can cause significant damage to car paint and skin, so extreme caution is required during handling.
19
2
Share

What Causes the Squeaking Noise in Brembo Brakes?

Brembo brakes producing squeaking noises may be caused by issues such as poor-quality brake pads, severely worn brake discs, or excessively worn brake pads. Brake Pad Quality: Substandard brake pads can cause abnormal noises during braking and may also damage the brake discs. It is necessary to replace them with genuine brake pads at an authorized 4S dealership. Severely Worn Brake Discs: When brake pads rub against severely worn brake discs, they can also produce abnormal noises. Prompt replacement of the brake discs is required. Excessively Worn Brake Pads: After prolonged use, brake pads naturally wear thin due to continuous friction. Excessively thin brake pads not only reduce braking effectiveness but also harden over time, leading to squeaking noises during braking. Timely replacement of the brake pads is the solution.
13
3
Share

Can a Dry Dual Clutch Be Repaired After Water Ingress?

Dry dual clutch can be repaired after water ingress. Clean water ingress: Try not to drive or run the engine, as the water will settle at the bottom of the gear oil in the transmission. Open the drain screw at the bottom of the transmission to drain all the water and oil, then add new gear oil. Component disassembly and cleaning: If dirty water or water with sediment enters, or if clean water enters and the vehicle is driven or the engine is run, the water and oil will emulsify due to high-speed mixing inside the transmission. It is difficult to separate the oil and water in this case, so the transmission must be removed, opened, and cleaned. If sediment enters the bearings, especially the input shaft bearing, all components inside the transmission must be disassembled and cleaned.
10
1
Share

When starting a motorcycle on a slope, should you release the clutch or the brake first?

When starting a motorcycle on a slope, first release the clutch while keeping the throttle steady. Slowly release the clutch until you feel the bike has a tendency to move forward, then stop releasing the clutch. Release the brake and start applying throttle while continuing to slowly release the clutch until it is fully engaged and the bike starts moving. Motorcycle starting techniques: Before starting the motorcycle, it's best to repeatedly squeeze and release the clutch lever to avoid any jerking when starting. The key to starting is coordinating the actions between the throttle and clutch. Squeeze the clutch lever, shift into low gear, gradually release the clutch lever with your left hand while slowly increasing throttle with your right hand. Solutions for stalling tendency: If the engine shows signs of stalling, increase the throttle. If the engine speed is too high, ease off the throttle. Try to control the engine speed so it doesn't get too high, maintaining a steady increase in engine speed throughout the process from "partial engagement" to "full engagement" of the clutch.
5
3
Share

How Many Times Can a Car Tire Be Patched?

Each tire brand has different standards. Some brands allow only one patch, while others permit two, but under very strict conditions, such as requiring the two damaged areas to not be too close to each other. Maintain Distance When Driving at High Speed: Avoid unnecessary or frequent braking to reduce tire damage. For your own safety, pay attention to the tread depth of the tires. Tires that are nearly worn out have reduced friction with the road, leading to longer braking distances, so avoid high-speed driving. Rotate the Tires on Your Vehicle Appropriately and Timely: Consistently check the tires during the vehicle's primary and secondary maintenance to ensure even wear and extend their service life. Tires with slightly larger outer diameters should be installed on the outer wheels.
1
1
Share

Can vehicle inspection be done on a mobile phone?

Vehicle inspection cannot be conducted on a mobile phone. You can only schedule the annual inspection time via mobile, but the actual inspection process must be carried out at a testing station. Vehicle Annual Inspection Process: This refers to the mandatory annual inspection procedure for motor vehicles. It is a required examination for all vehicles, equivalent to a physical check-up for the vehicle. The purpose is to promptly eliminate potential safety hazards and reduce the occurrence of traffic accidents, commonly referred to as vehicle inspection. Inspection Time: Vehicle owners can apply for an inspection compliance mark at the vehicle management office of the registration location up to three months before the expiration of the vehicle's inspection validity period (for cars registered after September 2012, the inspection interval is every six years). The inspection should be scheduled within three months before the annual registration date on the vehicle's license.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.