How to Display the Fuel Consumption Adjustment on the Mazda 3 Axela?

1 Answers
CatherineMarie
07/24/25 7:49pm
You need to press the info button on the left side of the steering wheel to switch, and then the fuel consumption will be displayed on the instrument panel. Below is some relevant information about the Mazda 3 Axela: 1. Exterior Introduction: As a new generation model, the Mazda 3 Axela has undergone comprehensive breakthroughs and innovations based on the forward-looking design and exquisite craftsmanship of the previous two generations. It features a longer wheelbase, with intersecting rising and descending waistlines that mimic the power and muscle lines of a cheetah in full sprint, embodying the style of luxury cars and coupes. 2. Technology Configuration: Particularly noteworthy is the "MZD CONNECT Mazda Connect System," which exudes a strong sense of luxury and technology. Its 7-inch multimedia display includes rich functions such as communication, entertainment, navigation, and rearview camera. Positioned upright on the center console, it effectively reduces the need for the driver to shift their line of sight, enhancing driving safety. Related functions can also be operated "blindly" via the central control knob behind the gear shift lever, allowing for a safer and more enjoyable driving experience.
Was this review help?
6
5
Share
More Forum Discussions

What is the method to unlock the Magotan audio password?

The audio system has a backup universal password. If the car audio is locked and the owner has forgotten the password, you can try to find the universal password for this car audio. Based on the serial number on the car audio, you can look up the original password for this car audio from the manufacturer or some technical documentation. A universal programmer can rewrite the car audio memory data. A universal programmer is a small instrument produced by professional manufacturers, used in conjunction with a computer.
17
1
Share

What to Do When the Airbag Warning Light Comes On After Water Intrusion in the Car?

If the airbag warning light is on, consider the possibility of a loose or disconnected airbag wiring. Start by checking the airbag wiring under the seats, moving from simple to complex. Inspect the airbag sensors. If a fault is found, replace the driver-side airbag sensor. Check the seat belt sensor, airbag connectors, airbag sensors, and the airbag control module. If any faults are detected, replace the airbag control unit.
16
3
Share

What to Do When the Car Gear Shift Area Gets Waterlogged?

It is necessary to replace rubber components such as gaskets and oil seals, change the friction plates, completely replace the transmission oil, and also replace the sprocket. Moderate water ingress requires far fewer parts to be replaced compared to severe water ingress, but components like gaskets, oil seals, and friction plates still need attention. The repair method for slight water ingress is similar to that for moderate water ingress, but the focus is mainly on prevention. It is advisable to replace gaskets, oil seals, friction plates, etc., to extend the service life.
4
5
Share

How to Adjust a Motorcycle Speed Limiter?

With the ignition switch turned off, turn the right-hand throttle grip to the maximum and pull the brake lever to the fullest with your right hand. Then, use your left hand to turn on the ignition switch, followed by releasing the throttle grip and brake lever with your right hand. Release the right-hand throttle grip and brake lever with your right hand. After fully releasing the throttle grip, quickly turn the throttle grip to the maximum and then release it completely twice with your right hand.
11
2
Share

How to Replace the Battery in an MG3 Car Key?

Eject the metal mechanical key; the key shell cannot be opened when the mechanical key is inserted. Press the physical button to eject the mechanical key, then turn the key sideways and pry upwards along the gap. Gently pry open the key shell to separate the "head" and "tail" of the key. Stand the tail of the key upright; from the gap on the back of the key, you can lift the key cover. Once the key cover is lifted, open it to replace the battery, then reassemble the key.
10
3
Share

What to Do When There's a Buzzing Noise While Stepping on the Gas Pedal?

Issues with components or severe wear can cause abnormal noises when parts don't interact smoothly, requiring troubleshooting. Loose parts on the chassis hitting against the car body can produce noise; lift the vehicle to inspect the chassis. Lack of long-term maintenance on the gas pedal may cause it to interfere with other parts, leading to noise. Perform timely maintenance and cleaning of the gas pedal. A comprehensive check at a 4S shop is recommended to enhance vehicle maintenance.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.