How to Display Lyrics on Mercedes-Benz Center Console?

1 Answers
JessicaLee
07/29/25 6:07pm
You can connect via Bluetooth or use the in-car app software to select the lyrics display option, then set up the lyrics display on the Mercedes-Benz center console screen. Call the Mercedes-Benz customer service hotline directly to inquire about how to handle it.
Was this review help?
16
4
Share
More Forum Discussions

How to Clean Engine Oil Stains Penetrated into Cement Floor?

Alcohol can dissolve in both organic solvents and water. The higher the alcohol concentration, the better, with anhydrous alcohol being the best option. Alcohol is available at pharmacies or chemical stores. Apply a small amount of essential balm on the clothing area stained with engine oil, and wash it together with the laundry. It's simple and effective for thorough cleaning. First, use gasoline to wipe the stain. For heavier oil stains, you can use paint thinner and turpentine. Once the oil stain dissolves, proceed with regular washing methods to clean it thoroughly. Use a soft cloth or cotton yarn dipped in gasoline to wipe the stain. The oil-based colored substances will dissolve in the gasoline and transfer to the cleaning cloth.
10
0
Share

How to Charge a Li Auto Vehicle?

Open the battery fluid filler cap. Check the electrolyte level, and if it is insufficient, first add distilled water. Connect the red clip to the 12V or 24V terminal as required by the battery. The red and black clips should be connected to the "+" and "-" terminals of the power source, respectively. Connect the "+" and "-" terminals of the battery to the corresponding positive and negative terminals of the charger. Properly connect the charger's power cord to the power outlet. Adjust the charging current using the regulator switch knob. Monitor the ammeter reading. The charging current should be between 10~15A; excessive current may damage the battery.
4
1
Share

Does lugging a manual transmission car affect the vehicle?

Lugging a manual transmission car does affect the vehicle. Prone to stalling: Under lugging conditions, the engine may operate near the critical speed, making it prone to stalling. Weak acceleration: When the engine speed is too low, there will be a phenomenon of weak power output (determined by the power-speed characteristics), resulting in weak acceleration. Increased fuel consumption: If the speed is too low, the car does not cover distance efficiently. Since fuel consumption is calculated based on a per 100 km standard, although the fuel consumption per unit time decreases, it takes several times longer to cover the same distance, leading to an overall increase in fuel consumption. Jerky movement: Insufficient power output while the car is trying to move forward can cause jerky movements, commonly known as "lugging," which can damage the transmission.
8
0
Share

How to Adjust the Audio System of the 3rd Generation Haval H6?

Turn on the head unit and play some high-fidelity vocal tracks or tracks with strong bass dynamics. Adjust the volume to slightly over half or 3/5 of the maximum level. First, increase the GAIN knob of CHANNEL-1/2 until the sound is very loud, then reduce the volume of the head unit. Typically, when the head unit volume is increased, vocals may sound nasal, as if having a cold, or the pronunciation may seem unclear. Regardless of the state of the front sound field, the rear sound field should be set to HP mode, and the CROSSOVER (cutoff frequency) should be adjusted to around 150Hz. Set the FILTER of the subwoofer amplifier to the LP (low-pass) position and adjust the CROSSOVER (cutoff frequency) to the lowest setting.
6
0
Share

Can Chassis Armor Be Sprayed on the Fuel Tank?

Paint can be applied to the fuel tank. Areas where it should not be sprayed: Generally, the chassis armor suitable for your vehicle is sufficient. The area from the beam base to the spare tire base can be sprayed, but the exhaust, suspension, and brake areas should not be painted. Additional Information: Before spraying, cover the brakes and suspension with newspaper, and remove the exhaust, wheels, and other parts. For new cars, the protective wax on the chassis must evaporate completely, and no thinner should be added. After the first coat, let it dry for 10 minutes before applying the second coat. Typically, 3-4 coats are applied, with thicker layers on areas like the fuel tank and fender. After spraying, the car should be parked in a garage to dry for 24 hours, avoiding contact with water. Avoid working in rainy or humid weather, as this can hinder the timely drying of the coating and affect the effectiveness of the chassis armor. After the chassis armor application, it is best not to drive on rough roads for about a day, as the coating may not have fully dried and cured.
13
2
Share

Does Modifying Car Lights Affect the Battery?

Generally, there is no impact. However, if the current is higher than the voltage stability rating of the original car lights, it can have an effect. Reasons: As long as the lights are used normally, modifying them will not affect the battery. Simply turn off the modified lights when parking and avoid using high-power electrical devices after turning off the engine, and the impact on the battery will be minimal. However, if the current of the modified lights exceeds the voltage stability rating of the original car lights, it can have an effect. Additional Information: The normal lifespan of a battery ranges from 1 to 8 years, depending largely on the condition of the vehicle. If the vehicle's alternator recharges normally and there are no electrical leaks or grounding issues, the battery can typically last over 3 years. If you notice that the battery isn't charging properly, the starter is weak, or the headlights are noticeably dimmer, you should remove the battery and charge it for 12-24 hours using a charger. If the problem persists and the mileage exceeds 50,000 KM, and the alternator is functioning correctly, you may need to consider replacing the battery.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.