How to Disassemble the Headlight Switch of the New Lavida?

1 Answers
LeBrooke
07/29/25 12:40pm
The steps to disassemble the headlight switch of the New Lavida are as follows: 1. Unplug the lighting combination switch connector of the car; 2. Unplug the connector linked to the wiper combination switch; 3. Remove the fixing screws of the headlight combination switch; 4. Use a screwdriver to remove the fixing screws of the headlight combination switch assembly. The body dimensions of the New Lavida are 4608mm in length, 1743mm in width, and 1465mm in height, with a wheelbase of 2610mm. It is equipped with 1.2T, 1.4T, and 1.5L naturally aspirated engines, paired with a 5-speed manual or 6-speed automatic transmission. The 1.4T engine delivers a maximum power of 110 kW and a maximum torque of 250 Nm; the 1.5L engine provides a maximum power of 85 kW and a maximum torque of 150 Nm.
Was this review help?
19
4
Share
More Forum Discussions

How many passenger seats can a B2 driver's license drive?

B2 driver's license can only drive blue-plate minibuses with 9 seats or less and a vehicle length under 6 meters. The vehicle types permitted by a B2 license include heavy and medium-duty trucks, mostly such as dump trucks; as well as large, heavy, and medium-sized special-purpose vehicles, which refer to vehicles equipped with special equipment or devices, such as sprinkler trucks, concrete mixer trucks, fire trucks, etc. The following are the initial application requirements for a B2 driver's license: the applicant must be at least 20 years old, with a height not less than 155cm, naked eye or corrected vision not less than 5.0, holding a C1 driver's license for three years or more, and no record of accumulating 12 penalty points in the scoring cycle when applying for the B2 license and the three consecutive scoring cycles before that.
2
3
Share

How to Start the Car in Subject 2?

Correct starting method for Subject 2: 1. Before starting, check whether the gear shift lever is in the neutral position. 2. Ignite and start the car, with both the clutch and brake fully depressed. 3. Engage the first gear, turn on the left turn signal, and release the handbrake. 4. If on flat ground, you can first fully release the brake, then slowly release the clutch to the semi-engaged state while gently pressing the accelerator pedal to start; if on a slope, you need to stabilize the brake and clutch to avoid stalling. Below is an introduction to Subject 2: 1. Subject 2 requires students to master the basic driving operation essentials and possess the basic ability to control the vehicle. They should be proficient in the basic methods of driving on the site and internal roads, have the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and be able to accurately control the vehicle's driving position, speed, and route. 2. If the Subject 2 test is failed, the applicant needs to first pay the retake fee at the vehicle management office and schedule a retake.
12
5
Share

How to Add Windshield Washer Fluid to an Audi A3?

Audi A3 Windshield Washer Fluid Refill Tutorial: 1. Use the wiper control knob to spray out the existing washer fluid. 2. Completely drain the old washer fluid, open the washer fluid filler cap, and add a small amount of new washer fluid. 3. Activate the wipers again to clear out any remaining old washer fluid. 4. When the spray nozzles stop dispensing fluid during the second activation, pour in 4 liters of new washer fluid, then securely close the filler cap. The method for preparing washer fluid varies by season. Here are the relevant details: 1. In summer when dust is prevalent, you can appropriately increase the amount of detergent, but do not exceed the recommended amount, as excessive foam can make it difficult to clean thoroughly. 2. In colder winter temperatures, adding more alcohol can lower the solution's freezing point. A mixture of 50-60% water and 40-50% alcohol can reduce the freezing point to -25°C, meeting the needs of most regions across the country.
19
2
Share

Does Canceling a Driving Test Reservation Count as One Attempt?

Early cancellation does not count as a test attempt, so students can rest assured. Each student has three opportunities to cancel a reservation for each subject, which is a legitimate and reasonable operation. Since driving test reservations are allocated based on ranking, users with higher priority are ranked higher and naturally scheduled for tests earlier. Normal cancellation of a reservation will not affect the ranking. If the reservation application has only been submitted successfully, it can be canceled directly online. If the reservation has been successfully confirmed and an SMS notification has been received, the student must bring their ID card to the vehicle management office to complete the cancellation procedure. Note that this must be done before the day before the test; otherwise, failure to cancel on time or not completing the cancellation procedure will be treated as an absence. Early cancellation does not count as a test attempt, so students can rest assured.
13
0
Share

Do I have to pay an exam fee for each subject of the driver's license test?

Summary: Generally, fees are required. If the tuition fee you paid when enrolling in the driving school did not include exam fees, then you will need to pay the exam fee for each test. If the tuition fee already includes the exam fees, then you won't need to pay for each test. However, this only applies to the first attempt of each subject. If you fail the exam and need to retake it, you will have to pay an additional retake fee. Typically, the tuition fee provided by driving schools covers the first exam fees, while retake fees are paid separately by the student.
13
3
Share

What are the reasons for Tesla to build a factory in China?

Tesla's reasons for building a factory in China: 1. Benefiting from policy support and cooperation with relevant departments. Tesla signed an investment agreement with the Lingang Management Committee and Lingang Group in Shanghai for a pure electric vehicle project. The agreement includes Tesla building a Gigafactory in the Lingang area, which will integrate R&D, manufacturing, sales, after-sales services, and other functions, along with related collaborations. 2. The Lingang area in Shanghai is one of China's six major automotive industry clusters, home to numerous auto parts and technology R&D companies. Establishing a presence here offers Tesla significant convenience for product production and R&D. Building a factory here can reduce transportation costs and facilitate collaborations with other automakers to promote its products, providing Tesla with considerable advantages. 3. Automotive R&D and manufacturing require a large workforce. Currently, China has a sufficient labor supply, and a vast pool of high-end talent is readily available in Shanghai.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.