How to Determine if the Jetta Synchronizer is Faulty?

1 Answers
StStephanie
07/30/25 3:28am
Methods to determine if the Jetta synchronizer is faulty: 1. A damaged car synchronizer can cause difficulties in shifting gears, accompanied by the sound of gear shift impacts; 2. During driving, if there is a situation where the gear jumps after upshifting, improper operation methods can lead to abnormal wear, burning, and failure of the synchronizer. Jetta is a car brand under FAW-Volkswagen Automotive Co., Ltd. Taking the Jetta VS5 as an example, it is a compact SUV under FAW-Volkswagen Jetta. In terms of body dimensions, its length, width, and height are 4419mm, 1841mm, and 1616mm respectively, with a wheelbase of 2630mm.
Was this review help?
6
3
Share
More Forum Discussions

Where is the sunroof drain outlet located on the Buick Envision?

Buick Envision's sunroof drain holes are located near the sunroof sliding rails, which become visible when the sunroof is fully opened. All vehicles equipped with sunroofs have sunroof drain holes. Without these drain holes, the sunroof would leak during rainfall. Here are some additional details: 1. When the sunroof leaks: If the sunroof leaks, check whether the drain outlets are clogged with dust. Routine maintenance of the car sunroof doesn't require special procedures, just periodically inspect the surrounding sealing strips for damage and check the lubrication condition of the tracks. 2. Air conditioning drain hole: The air conditioning drain hole is designed to discharge water droplets formed by the condensation of surrounding air due to excessively low temperatures during air conditioning use. This drain hole is typically located at the bottom of the heater evaporator, above the front wall panel of the passenger compartment. Regular maintenance should also include checking these drain holes.
16
0
Share

How many kilometers can a MG 5 run on a full tank of gas?

MG 5 can run 600-700 kilometers on a full tank of gas. Fuel consumption per 100 km parameters: Fuel consumption per 100 kilometers refers to the fuel consumption of a vehicle traveling 100 kilometers at a certain speed on the road, which is a theoretical indicator of the vehicle. The fuel consumption per 100 km is a value measured by the manufacturer in an objective environment using a dynamometer installed on the vehicle chassis, converted into speed parameters, and then calculated at specified speeds to obtain the theoretical experimental fuel consumption data per 100 km for the model. Road condition fuel consumption: Road condition fuel consumption is a fuel indicator calculated by repeatedly testing the values measured when a vehicle travels on specified roads at prescribed speeds and times, also known as multi-condition road cycle fuel consumption.
14
5
Share

Is It Normal for a Car Not to Generate Electricity at Idle but to Generate When Accelerating?

It is normal for a car not to generate electricity at idle but to generate when accelerating. Below are the specific details about the car alternator: Working Principle: When the external circuit supplies current to the excitation winding through the brushes, a magnetic field is generated, magnetizing the armature into N and S poles. Maintenance: Regularly clean the accumulated dirt and dust on the alternator's surface to maintain cleanliness and ensure good ventilation. Periodically check the tightness of all fasteners related to the alternator and promptly tighten any loose screws. Function: The car alternator is the primary power source of the vehicle. Its role is to supply power to all electrical devices (except the starter) when the engine is running normally and to recharge the battery.
15
3
Share

Can Manual Transmission Skip a Gear When Downshifting?

Manual transmission can skip a gear when downshifting. This is particularly necessary when driving on slippery surfaces such as snow, ice, or mud, when the vehicle's driving resistance increases, or in the event of brake failure. Skipping a gear helps reduce speed, prevent the vehicle from skidding sideways, and ensure the safety of the driver and passengers. Skipping a Gear When Downshifting: Skipping a gear means the driver does not downshift in the normal sequence (e.g., 5-4-3-2-1) but instead skips one gear, such as shifting directly from 5th to 3rd or 4th to 2nd. Effects of Skipping a Gear in Manual Transmission: It can increase fuel consumption and oil usage, lead to more carbon buildup, and cause unstable engine idling, all of which have a very negative impact on the vehicle.
15
4
Share

What to Do When Two Driving Test (Subject Three) Sessions Are Booked?

If two sessions for Subject Three are booked, one of them needs to be canceled: Specific methods: If you are unable to attend the test due to personal reasons, you can cancel the reservation in advance. If you have not received an SMS notification confirming the successful booking, you can cancel it via the Traffic Management 12123 app or the provincial road traffic service platform. If you have already received the SMS notification, you must bring your ID card to the local vehicle management office to cancel. Subject Three: Subject Three includes the road driving skills test and the safety and civilized driving knowledge test. It is part of the motor vehicle driver's license assessment and is the abbreviation for the road driving skills and safety and civilized driving knowledge test subjects in the motor vehicle driver's examination.
8
2
Share

What does 909010 mean for motorcycles?

Motorcycle 909010 indicates that the length, width, and height of the motorcycle are 90mm, 90mm, and 10mm respectively. Specific meaning of 909010: 90 represents the tire width, measured from the sidewalls of the inflated tire, which is 90 millimeters. 90: represents the aspect ratio of the tire, which is the ratio of the tire height to width, at 90%. A higher ratio means the tire is rounder, while a lower ratio indicates a flatter tire. 10 represents the tire diameter of 10 inches. Method for measuring tires: Measurement point A is located at the center plane of the tire, measuring the distance at the rear of the tire; rotate point A 180 degrees to measurement point B at the front of the tire, with the height located at the center plane of the tire, measuring distance B at the front of the tire. A-B is the measured toe-in.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.