How to Determine if a B2 Driver's License Requires Annual Inspection

1 Answers
NorahAnn
07/30/25 8:45am
b2 driver's license holders should undergo inspection at the traffic management department of the public security authority within 30 days after the end of each scoring cycle. Those with no demerit points during a scoring cycle are exempt from annual inspection. Below is relevant information about vehicle annual inspection: 1. Inspection rules: According to Article 16 of the Regulations for the Implementation of the Road Traffic Safety Law, effective from July 1, 2018, motor vehicles must undergo safety technical inspections within the following periods from the date of registration: operational passenger vehicles require annual inspection every year within 5 years, and every 6 months after exceeding 5 years. 2. Rules for vehicle inspection labels: Starting from June 20, 2020, electronic motor vehicle inspection label services have been implemented nationwide. Electronic inspection labels are issued through the unified national internet traffic safety comprehensive service platform.
Was this review help?
16
0
Share
More Forum Discussions

Should a 1.5T engine use 92 or 95 gasoline?

There is no definitive answer to this question. It is recommended to check the vehicle's manual for fueling instructions. Below are some precautions regarding car refueling: 1. Use the gasoline grade indicated on the fuel tank cap: When refueling your car, follow the gasoline grade required by the manufacturer's manual or as indicated on the fuel tank cap. A higher gasoline grade only indicates better anti-knock performance, not necessarily better engine power output. The best gasoline grade is the one that matches your car's engine compression ratio. 2. Refuel when the fuel light comes on: Many people believe that the fuel pump is submerged in the fuel tank, and if the fuel light comes on, it means the fuel level is below the pump. They think that if the pump is not effectively cooled, its lifespan will be reduced or it may even get damaged. In fact, this is incorrect. The fuel pump is not cooled by the fuel submerged in the tank but by the fuel drawn into the pump. As long as fuel can still be drawn in, the cooling process continues. 3. Avoid using mobile phones while refueling: Gas stations have clear regulations prohibiting the use of mobile phones during refueling. Mobile phones emit electromagnetic radiation, and when metal encounters charged particles, it can generate sparks, ignite gasoline, and even cause explosions. Although the probability of an explosion is very low, the danger still exists.
8
0
Share

What Causes Scooter Shaking During Takeoff?

The reasons for scooter shaking during takeoff are as follows: 1. Friction Plate: The contact area between the friction plate and the clutch housing working surface is too small. Solution: Apply chalk to the surface of the clutch shoe friction plate, install the clutch, start the engine, and repeatedly accelerate-brake to stop the rear wheel. After several repetitions, remove the clutch to inspect the working contact surface of the shoe friction plate. Use a grinding wheel to polish the surface of the clutch shoe friction plate, ensuring the contact area between the friction plate and the clutch housing working surface exceeds 80% of the total area. 2. Clutch Friction Plate: Excessive wear of the clutch friction plate. Solution: Use a file to trim the chamfers at both ends of the clutch friction plate, increasing the chamfer size that has been reduced due to wear. 3. Clutch Shoe: Sticking of the clutch shoe on the pin. Solution: Clean and lubricate the installation pin (i.e., the drive plate pin) of the clutch shoe and the pin hole on the clutch shoe to eliminate sticking of the clutch shoe on the pin. 4. Small Spring: Damage to the small spring of the clutch shoe. Solution: Replace the three small tension springs of the clutch shoe, ensuring equal tension among them to eliminate the asynchronous engagement between the clutch friction plate and the clutch housing.
15
0
Share

Why does the scooter jerk when accelerating?

The reasons for uneven acceleration in a scooter are as follows: improper ignition timing adjustment, either too early or too late. Incorrect spark plug gap adjustment, either too large or too small. Wear on the engine cylinder walls, causing poor sealing of the piston rings. Contaminants in the carburetor or fuel line, leading to poor fuel supply. Improper carburetor adjustment, resulting in a mixture that is too rich or too lean. A dirty air filter, causing restricted air intake. A stiff or stuck throttle cable, making it difficult to operate. More related information is as follows: 1. Solution: When accelerating, if the engine runs smoothly and hums, it proves the engine is fine; otherwise, it could be a clogged fuel line or electrical issue in the carburetor. If the engine is fine, the issue might be with the scooter's continuously variable transmission (CVT), meaning the engine's power isn't being efficiently transmitted to the rear wheel. The CVT has a friction plate—if it's worn thin, a mechanic can replace it. 2. Overview: Scooters use a continuously variable transmission with an automatic clutch. The automatic clutch mainly operates through mechanical, electronic, or hydraulic systems to control clutch engagement and disengagement independently. It consists of a clutch drive mechanism, control unit, gear sensor, wiring harness, display/voice unit, etc., and is primarily designed for manual transmission vehicles without altering the original structure. The control unit simulates optimal driving techniques based on the vehicle's state (speed, RPM, throttle, brake, gear shift) and the driver's intent, using the best timing and speed to control the clutch drive mechanism. This ensures quick disengagement and smooth engagement, providing comfortable starts and gear shifts while avoiding engine stalling or unnecessary revving.
7
5
Share

What is the maintenance reset method for the Haval H6 1.5T?

The maintenance reset method for the Haval H6 1.5T is to insert the key, press the reset button, turn on the ignition, and observe the display screen. When it shows 0000.0, release the button. Below is some relevant information about the Haval H6: 1. Fuel consumption is not high: Compared to other self-owned brand models in the same class, the Haval H6's fuel consumption is not particularly high but rather relatively balanced. Therefore, users choose to save money while saving fuel. 2. High resale value: The Haval H6 has a high resale value, a large number of units in circulation, a vast user base, and the advantage of easy maintenance with affordable parts.
14
5
Share

What Type of Driver's License is Required for Large Buses

Large buses require an A1 driver's license. Below are the relevant details:1. Upgrading from C1: Large buses require an A1 license, while large trucks require a B2 license. Neither can be obtained directly; the minimum requirement is upgrading from a C1 license. You can upgrade to B2 after holding a C1 license for one year, and to B1 after three years. Upgrades can only be processed at the location of your household registration.2. Requirements for upgrading from C1 to B1: Hold a C1 driver's license for more than three years, have no record of drunk driving, and be aged between 21 and 50 years old.3. Definition of a driver's license: A motor vehicle driver's license is a legal document issued by the administrative authorities, certifying that the holder has learned and mastered traffic regulations and driving skills, and has passed the relevant tests, permitting them to drive a certain type of motor vehicle.
11
3
Share

Which light to use when turning at a signalized intersection?

When turning at a signalized intersection, turn on the left or right turn signal as appropriate. Here is some knowledge about turn signals: 1. Introduction: The turn signal is an important indicator light that is turned on when a motor vehicle is turning to alert vehicles and pedestrians in front, behind, and to the sides. The turn signal tube uses a xenon tube, controlled by a single-chip microcomputer circuit, with left and right alternating flashing for continuous operation. The turn signal uses a flasher to achieve light flashing. It can be mainly divided into three types: resistance wire type, capacitor type, and electronic type. 2. Structural principle: The resistance wire type can be further divided into hot wire type (electrothermal type) and vane type (bounce type), while the electronic type can be divided into hybrid type (with contact-type relays and electronic components) and fully electronic type (without relays). For example, the bounce-type flasher uses the principle of current thermal effect, with thermal expansion and contraction as the driving force, causing the spring plate to make sudden movements to connect and disconnect the contacts, thereby achieving light flashing.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.