How to Deduct 6 Points Through Traffic Law Learning?

1 Answers
Elijah
07/25/25 2:55pm
Driver users should click the business function on the homepage, select the 'Traffic Law Learning' button under the education and learning business module to enter the application page for point deduction through learning. Click the application button, read the business instructions, and review the information displayed on the submission interface. For incorrect mobile phone numbers, you can jump to the modification interface to make corrections. If the data is correct, click the submit button.
Was this review help?
3
2
Share
More Forum Discussions

How many kilometers should a vehicle drive for its first maintenance?

The first maintenance for a car is best done at 3,000 kilometers. If the car is driven infrequently and it takes a long time to reach 3,000 kilometers, it is recommended to perform the first maintenance within three months. After a new car is purchased, the 4S shop usually requires the owner to perform the first maintenance within 3,000 kilometers. In fact, the car manufacturer requires the owner to complete the first maintenance within 5,000 kilometers. Therefore, it is crucial not to exceed 5,000 kilometers before performing the first maintenance. Failure to follow the normal maintenance schedule as per the user manual may result in the vehicle being considered out of warranty, and the 4S shop and manufacturer may refuse to provide warranty services if issues arise. Additional Information: 1. When a new car leaves the factory, the various components have not yet fully integrated. During the initial driving period, since the moving parts of the car have not been broken in, it is essential to use the vehicle carefully to avoid exacerbating component damage. The break-in period allows the engine parts to smoothly adapt to each other, and a proper break-in can extend the vehicle's lifespan. Therefore, new cars require a break-in period, which is generally 5,000 kilometers. 2. When the new car reaches 2,300 kilometers, it is imperative to take it to the dealership for maintenance, which is usually free for the first time. Changing the engine oil, three filters, and gear oil is crucial because the first oil and gear oil change removes fine metal particles generated during the break-in period. Not changing them can harm the engine. Subsequently, the engine oil and three filters should be changed every 5,000 kilometers.
15
0
Share

Where is the chassis number rubbing location for the Audi Q3?

The Audi chassis number can be found in several locations: the first is on the front inner wall panel of the car, two more are located below the seatbelt on the left B-pillar, and another one is in the spare tire well. Introduction to the chassis number: Abbreviated as VIN, it is a unique set of seventeen alphanumeric characters used on vehicles to identify the manufacturer, engine, chassis serial number, and other specifications. Introduction to the identification code digits: The first digit of the identification code represents the country of production. The second digit represents the manufacturer. The third digit represents the type of vehicle. Combining these three digits generally gives an idea of what kind of vehicle it is.
1
0
Share

Where is the crash sensor located on the Passat B5?

The crash sensor on the Passat B5 is located below the headlights. Introduction to the crash sensor: The crash sensor is used to detect and determine the impact signal when a collision occurs, in order to promptly deploy the airbag. Introduction to the airbag: It is a common passive safety device in cars. The function of the airbag is to form a cushion between the driver and the steering wheel, and between the front passenger and the dashboard, to prevent injuries from hard impacts. The airbag system generally consists of a crash sensor, an electronic control unit (ECU), an airbag module (including a gas generator, airbag, and igniter), a monitoring device, and a backup power supply.
16
0
Share

What Causes the Noise in the Driver's Seat of the New BMW 3 Series?

The main reasons for the noise in the driver's seat of the new BMW 3 Series are as follows: Bearing Damage: Usually, it's the bearing making noise, or the bearing is damaged, causing friction between the rotor and stator. If the bearing is noisy or damaged, you can replace the bearing and then maintain the generator's rotor. Loose Fan Blade: If it's a loose fan blade, it's even simpler—just tighten it. If the car is still under warranty, you can directly request a new generator replacement. Of course, you must go to an authorized 4S dealership and insist on a new generator, ensuring it's an original factory part and strictly rejecting aftermarket parts. Noise issues can be directly addressed by requesting a replacement.
13
4
Share

What is Mercedes-Benz Intelligent Vehicle-Home Connectivity?

This is the vehicle's interactive system. The in-car monitoring system and anti-theft alarm system will detect movement inside the vehicle after locking and sound an alarm. You can remotely unlock the car doors or alert people nearby through the smart connectivity system on your phone. Development Status: In 2016, the Ministry of Industry and Information Technology organized the industry to accelerate the formulation of a development strategy, technology roadmap, and standard system for intelligent connected vehicles. The Ministry of Transport has also accumulated rich experience in intelligent traffic management through the implementation of "two buses and one micro" vehicle management. Development Prospects: Minister of Industry and Information Technology Miao Wei previously stated that non-traditional automotive industry enterprises are encouraged to cooperate with current automobile manufacturers to promote innovation and enhance competition.
18
2
Share

What is the cause of Mercedes-Benz P001700 fault?

P001700 fault refers to the camshaft sprocket fault, which is most likely caused by dirty engine oil. It is recommended that the owner go to the 4S shop to replace the engine oil first, and then check the solenoid valve with a computer. Common faults of the car body include: Paint film peeling: It is caused by the ultraviolet effect, drastic changes in ambient temperature and humidity, contamination, aging and mechanical damage, which deteriorate or peel off the paint film of the car body. Wiper failure: It manifests as the wiper not working or working weakly, incorrect swing range and swing angle, unclear speed change or uncontrollable speed, etc. It is related to the failure or malfunction of the wiper motor, speed change switch, and mechanical parts such as the wiper swing rod.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.