How to Deal with Water Leakage Under the Passenger Seat?

1 Answers
DelGia
07/30/25 7:57am
The method to handle water leakage under the passenger seat is to use a wire to unclog the drainage hole. The area under the passenger seat contains the air conditioning drainage hole. If it gets blocked, the water from the air conditioning system cannot drain out and will flow back into the cabin, causing water to seep out onto the floor of the passenger side. This issue should be addressed promptly to prevent the carpet from getting wet and developing mold. Common areas in a car prone to water leakage include: 1. Sunroof: Leakage from the sunroof can occur due to two main reasons. One is an issue with the sunroof drainage outlet, often caused by blockages from dust, leaves, or twigs, preventing proper drainage and leading to water seepage. This is a common problem with sunroof leaks. The other reason is the aging of the sealing strip. 2. Trunk: Water leakage into the trunk happens when rainwater flows through the tail light area into the trunk, usually due to aging of the trunk seal. Replacing the seal strip can resolve this issue.
Was this review help?
14
4
Share
More Forum Discussions

Where to Sell Waste Tire Rubber Powder?

Waste tire rubber powder is sold to specialized recycling and processing plants for reuse. Waste tire rubber powder: It is the primary form of processed waste tires, and the application fields of rubber powder are broader than those of reclaimed rubber. For example, it is used in the construction of runways, school sports fields, garden paths, bowling alleys, sidewalks, rubber floor tiles, plastic runways, lawn quartz sand, cottonseed hull pellet meal, tennis courts, volleyball courts, golf courses, airplane fields, and other venues. Manufacturing equipment: Waste tire rubber powder equipment can process waste tires and rubber into ultra-fine rubber powder (30--200 mesh) and simultaneously separate the three main materials contained in the tires: rubber, steel wire, and fiber. Through the use of "rubber reducing agents," waste rubber can be restored to its pre-vulcanized state to produce various rubber products, achieving waste recycling and reuse.
18
1
Share

What is the minimum ground clearance of the Song Plus-DMI?

The minimum ground clearance of the Song Plus-DMI is 160mm. Here is some information about minimum ground clearance: 1. Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. It is used to indicate the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. 2. The smaller the ground clearance, the worse the ability to overcome obstacles. Sedans generally travel on flat urban roads, so they have smaller ground clearance; off-road vehicles have larger minimum ground clearance to pass over larger obstacles.
6
5
Share

What lights are referred to as headlights?

Turning on the headlights refers to the high beam, low beam, and turn signals of a car. Headlights: Also known as front headlights, they are installed on both sides of the front of the car and are used for illuminating the road during nighttime driving. They can be categorized into two-lamp and four-lamp systems. The illumination effect of headlights can directly affect nighttime driving operations and traffic safety. High beam: The intensity of the light is adjusted based on the distance of the filament. The high beam is focused, emitting light that travels parallel and is more concentrated, with greater brightness, allowing it to illuminate distant and high objects. Low beam: Beyond its focal point (between 1x and 2x the focal distance), the emitted light diverges, illuminating a larger area of nearby objects. Turn signal: An important indicator light that is activated when a vehicle is turning to alert surrounding vehicles and pedestrians. The turn signal uses a xenon tube and is controlled by a microcontroller circuit, operating in an alternating left-right flash pattern continuously.
3
1
Share

Is Steering Wheel Vibration Normal When the Air Conditioning is On?

Steering wheel vibration when the air conditioning is on is not normal. The specific reasons for steering wheel vibration when the air conditioning is on are as follows: Dirty Throttle Body: In this case, the engine will vibrate slightly, but it is usually not noticeable. However, once the air conditioning is turned on, the engine load increases, and the vibration intensifies. The solution is to clean the throttle body and simultaneously check whether the condenser is dirty or blocked and if there are any issues with the ignition system. Damaged Air Conditioning Compressor: This is the most severe cause because once it is damaged, there is basically no possibility of repair, and it can only be replaced. Generally, older cars over 6 years old may experience this issue, while new cars rarely do. Along with the vibration, another accompanying problem is that the air conditioning does not blow cold air, but the blower keeps running.
9
4
Share

How to Remove Old Paint?

Methods for removing old paint from cars include sandblasting, manual removal, mechanical removal, chemical removal, electric sanding, and flame scraping. Among these, manual removal, mechanical removal, and chemical removal are more commonly used. More details are as follows: 1. Chemical removal involves using paint strippers to eliminate old paint films. Commonly used strippers in the past were T-1 and T-2. T-1 stripper is a milky white paste-like liquid composed of ketones, alcohols, benzene, ester solvents, and an appropriate amount of paraffin. It is mainly used to remove old paint films of oil-based paints, ester gum paints, and phenolic paints. T-2 stripper is a mixture of ketones, alcohols, esters, and benzene solvents, with stronger paint film swelling ability and faster removal speed than T-1. It is primarily used for removing old paint films of oil-based paints, alkyd paints, and nitrocellulose paints. 2. Manual removal is a common method in painting work and the only method for partially removing old paint films. It mainly relies on tools like scrapers, knives, wire brushes, and sandpaper to remove old paint from the surface of car body components. This method is simple but labor-intensive and inefficient. 3. Mechanical removal uses electric or pneumatic tools, such as wire wheels, wire sanders, and dry/wet sandpaper sanders, to replace manual scraping and sanding. This method not only improves efficiency but also reduces labor intensity, making it widely used in the car body repair industry.
8
3
Share

What's the reason why the Fengguang 580 won't start?

The reasons why the Fengguang 580 won't start are as follows: 1. Circuit or electronic failure: The phenomenon occurs very suddenly without any warning. Circuit failures include: blown fuse, open circuit in the high-voltage coil, open circuit in the low-voltage circuit, detached central ignition wire, leaking distributor rotor, damaged spark plug. Electronic failure mainly refers to the malfunction of the central computer control board. 2. Fuel system failure: Possible locations of fuel system failures include: malfunctioning fuel pump, blocked fuel line, clogged fuel filter, carbon buildup on spark plugs, damaged fuel injectors, etc. 3. Mechanical failure: Common mechanical failures include: broken timing belt (chain), cylinder leakage with no pressure, etc.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.